准备工作
由于校园网"维护"后过于拉跨, 决定重新启用了菊厂的
随行wifi2mini
, 但是有一个关键问题是流量卡已经是Nano卡了, 但这玩意儿只支持大卡🤨…刚好这次手边有个3D打印机, 不如直接自己打个卡套😎
那就开始搜尺寸吧
但是…
不管是百度还是谷歌搜到的都是这样的结果
虽然的确有尺寸, 但是距离能做出卡套还缺了不少东西, 只好求助Wiki大大了, 不过这一查还挺涨见识:
Wiki
在wiki里检索SIMCard
就能找到这一页, 往下翻翻就能看到这张表格
这个表格里面居然有直接指向了相关标准的信息(好耶!), 直接复制出来搜索
结果踩坑了🤕
这个标准的V11.0.0的版本, 在它官网的搜索里面是搜不出来的
而且关键字只能是102 221
, 既不能是全部的ETSI TS 102 221 V11.0.0
, 也不能是102 221 V11.0.0
, 前者会优先匹配ETSI TS
,和没搜没啥区别; 后者则大部分匹配了V11.0.0
; 到最后只检索102 221
的时候, 却没有V11.0.0
😂
算了, 直接谷歌了, 结果排位第一的就是这个V11.0.0
的PDF链接🙄
翻目录, 直奔第四章😏
果然, 找到了2FF(SIM Card)
, 3FF(Micro SIM)
和4FF(Nano SIM)
的技术图, 还被顺手科普了一回(好家伙)
接下来是科普时间🧐!(引用的都是标准中的原文)
SIM卡(Plug-in UICC)(2FF)
The Plug-in UICC shall have a width of 25 mm, a height of 15 mm, a thickness the same as an ID-1 UICC and a feature
for orientation.
Annex A of ISO/IEC 7816-2 [10] applies with the location of the reference points adapted to the smaller size. The three
reference points P1, P2 and P3 measure 7,5 mm, 3,3 mm and 20,8 mm, respectively, from 0. The values in figure 2 of
ISO/IEC 7816-2 [10] are replaced by the corresponding values of figure 4.1.
The physical characteristics of the Plug-in UICC (Plug-in card) are defined in the present document.
Micro SIM(Mini-UICC)(3FF)
The Mini-UICC shall have a width of 15 mm, a height of 12 mm, a thickness the same as an ID-1 UICC and a feature
for orientation.
Annex A of ISO/IEC 7816-2 [10] applies with the location of the reference points adapted to the smaller size below
figure 4.2. The values in figure 2 of ISO/IEC 7816-2 [10] are replaced by the corresponding values of figure 4.2.
The physical characteristics of the Mini-UICC are defined in the present document.
Nano SIM(4FF)
The 4FF shall have a width of 12,3 mm ± 0,1 mm and a height of 8,8 mm ± 0,1 mm, with a thickness range of 0,67 mm + 0,03 mm/-0,07 mm. Annex A of ISO/IEC 7816-2 [10] applies with the location of the reference points adapted to the smaller size defined below in figure 4.3. The values in figure 2 of the ISO/IEC 7816-2 [10] are replaced by the corresponding values of figure 4.3. Optionally, the 4FF may be supplied within a card whose width and length are compliant with the ID-1 UICC dimensions but thickness compliant with 4FF. (🚨) In that case, the 4FF shall be located from 18,22 mm from the top edge of the card and 9,25 mm from the left edge of the card. ** The physical characteristics of 4FF are defined in the present document. The 4FF shall comply with all the characteristics in ISO/IEC 7816-1[9], except for bending and torsion properties, which apply only to the ID1 form factor. The definition of bending and torsion properties for the 4FF is FFS.
🚨注意: 虽然ID-1 UICC
的SIM卡已经 没有了 很少见了, 但标准中所有的芯片定位依然是以该板作为基准的(比如4FF中的加粗部分), 也就是说图纸中所有的upper edge
和left edge
全是ID-1 UICC
的尺寸🤒
至于ID-1 UICC
究竟是什么呢😶?
回去翻Wiki🤔:
其实当时因为没有尺寸直接忽略掉这张图了😂, 后来回到页面上才看到的这张图
没错就是最左边的板子, 看起来可能觉得没见过, 但其实…它和信用卡是同款(世界线收束!)🤯
(震惊了好久…)
开干咯🤠
简单的建模(NX10)…
然后就是导出到打印机的格式, 试制第一版就出炉啦
返工😥(再踩坑)
由于忽略了打印机的误差, 又踩了几个小坑:
第一版直接在平台上打印的, 取下来的时候过于暴力导致卡套变形的不成样子根本没法用了😑
第二版不仅Nano卡装不进去, 大卡也插不进卡槽😂(或许是因为外边缘直接打在平台上了摊开了), 于是把孔扩了一下(宽高各加了1mm, 斜角微调), 又加了个大平面支撑
第三版发现孔扩大了, Nano卡在里面逛荡😂, 于是把宽高的延长改为0.5mm(斜角再微调)
终于! 第四版能用啦😆
(FL: 第一版; FR: 第二版; RL: 第三版; RR: 第四版)
装卡!起飞!🤠
参考资料
- SIM card - Wikipedia
- TS 102 221 - V11.0.0 - Smart Cards; UICC-Terminal interface; Physical and logical characteristics (Release 11) (etsi.org)
周边参考资料