前言:最近又重拾stm32,希望借助博客记录自己的所学并有所提高
介绍stm32什么的就不说了,直接从点亮led开始吧
例子一(点亮led)
在进行编程前,需要知道:
1.如果要使用stm32的io口,需要先对io口进行初始化。这个初始化函数包括以下几个部分:
GPIO_InitTypeDef GPIO_InitStructure;//定义一个结构体,必须放在开头
RCC_AHB1PeriphClockCmd(RCC_AHB1Periph_GPIOF,ENABLE);//对f端口的时钟进行初始化,必须要有这一步,否则不能用io口
GPIO_InitStructure.GPIO_Mode=GPIO_Mode_OUT;//io口的模式为输出模式
GPIO_InitStructure.GPIO_Pin=GPIO_Pin_10;//指定管脚
GPIO_InitStructure.GPIO_Speed=GPIO_Speed_100MHz;//速度
GPIO_InitStructure.GPIO_OType=GPIO_OType_PP;//推挽输出
GPIO_InitStructure.GPIO_PuPd=GPIO_PuPd_UP;//默认为上落,即默认io口开始为高电平
GPIO_Init(GPIOF,&GPIO_InitStructure);//在声明一下,别忘了取地址符
第一步:建立led.h led.c,在led.h里面声明初始化函数:
void LED_Init(void);
在led.c中定义这个初始化函数。
#include "led.h"
void LED_Init()
{
GPIO_InitTypeDef GPIO_InitStructure;//¶¨Òå½á¹¹Ì壬±ØÐë·ÅÔÚ¿ªÍ·
RCC_AHB1PeriphClockCmd(RCC_AHB1Periph_GPIOF,ENABLE);
GPIO_InitStructure.GPIO_Mode=GPIO_Mode_OUT;
GPIO_InitStructure.GPIO_Pin=GPIO_Pin_10;
GPIO_InitStructure.GPIO_Speed=GPIO_Speed_100MHz;//ËÙ¶È
GPIO_InitStructure.GPIO_OType=GPIO_OType_PP;//ÍÆÍÆÍìÊä³ö
GPIO_InitStructure.GPIO_PuPd=GPIO_PuPd_UP;//ÉÏÀ
GPIO_Init(GPIOF,&GPIO_InitStructure);//ÔÚÉùÃ÷Ò»ÏÂ
第二步
写主函数:
#include "stm32f4xx.h"
#include "led.h"
void delay()
{
int a,b;
for(a=5000;a>=0;a--)
for(b=1000;b>=0;b--);
}
int main()
{
LED_Init();
while(1)
{
GPIO_ResetBits(GPIOF,GPIO_Pin_10);
delay();
GPIO_SetBits(GPIOF,GPIO_Pin_10);
delay();
}
}
说明:
1.
GPIO_ResetBits(GPIOF,GPIO_Pin_10)
是用来让某一管脚输出0
2.
GPIO_SetBits(GPIOF,GPIO_Pin_10);
是用来让某一管脚输出1
3.
这里的delay是用来粗略延迟,但是往后学我们知道stm32里面有更精确的延迟的方法,即systick,以后再说。
4.最后要说,以后再添加头文件时,一定要放进app中。并且还要在设置中添加头文件路径