Emulex光纤卡lpfc配置文件的修改

原创 2004年08月28日 12:09:00

光纤卡安装以后,需要修改两个配置文件,分别为:

/kernel/drv/sd.conf

/kernel/drv/lpfc.conf

修改内容在以下过程中标注:

# cd /kernel/drv
# vi sd.conf
"sd.conf" 65 lines, 1611 characters
#
# Copyright (c) 1992, by Sun Microsystems, Inc.
#
#ident  "@(#)sd.conf    1.9     98/01/11 SMI"

name="sd" class="scsi" class_prop="atapi"
        target=0 lun=0;

name="sd" class="scsi" class_prop="atapi"
        target=1 lun=0;

name="sd" class="scsi" class_prop="atapi"
        target=2 lun=0;

name="sd" class="scsi" class_prop="atapi"
        target=3 lun=0;

name="sd" class="scsi"
        target=4 lun=0;

name="sd" class="scsi"
        target=5 lun=0;

name="sd" class="scsi"
        target=6 lun=0;

name="sd" class="scsi"
        target=8 lun=0;

name="sd" class="scsi"
        target=9 lun=0;

name="sd" class="scsi"
        target=10 lun=0;

name="sd" class="scsi"
        target=11 lun=0;

name="sd" class="scsi"
        target=12 lun=0;

name="sd" class="scsi"
        target=13 lun=0;

name="sd" class="scsi"
        target=14 lun=0;

name="sd" class="scsi"
        target=15 lun=0;

# Start lpfc auto-generated configuration -- do NOT alter or delete this line
# WARNING:  anything you put within this auto-generated section will
# be DELETED if you execute pkgrm to remove the lpfc driver package.
# You may need to add additional lines to probe for additional LUNs
# or targets. You SHOULD delete any lines that represent lpfc targets
# or LUNs that are not used.
# You should add any new entries between this line
# and the End lpfc auto generated configuration line
# name="sd" parent="lpfc" target=16 lun=0;
# name="sd" parent="lpfc" target=17 lun=0;
# A small number of LUNs for a RAID array
# name="sd" parent="lpfc" target=17 lun=1;
# name="sd" parent="lpfc" target=17 lun=2;
# name="sd" parent="lpfc" target=17 lun=3;
name="sd" parent="lpfc" target=0 lun=0;
name="sd" parent="lpfc" target=0 lun=1;
name="sd" parent="lpfc" target=0 lun=2;
name="sd" parent="lpfc" target=0 lun=3;
name="sd" parent="lpfc" target=0 lun=4;
name="sd" parent="lpfc" target=0 lun=5;
name="sd" parent="lpfc" target=0 lun=6;
name="sd" parent="lpfc" target=0 lun=7;
name="sd" parent="lpfc" target=1 lun=0;
name="sd" parent="lpfc" target=1 lun=1;
name="sd" parent="lpfc" target=1 lun=2;
name="sd" parent="lpfc" target=1 lun=3;
name="sd" parent="lpfc" target=1 lun=4;
name="sd" parent="lpfc" target=1 lun=5;
name="sd" parent="lpfc" target=1 lun=6;
name="sd" parent="lpfc" target=1 lun=7;
name="sd" parent="lpfc" target=2 lun=0;
name="sd" parent="lpfc" target=3 lun=0;
name="sd" parent="lpfc" target=4 lun=0;
name="sd" parent="lpfc" target=5 lun=0;
name="sd" parent="lpfc" target=6 lun=0;
name="sd" parent="lpfc" target=7 lun=0;
name="sd" parent="lpfc" target=8 lun=0;
name="sd" parent="lpfc" target=9 lun=0;
name="sd" parent="lpfc" target=10 lun=0;
name="sd" parent="lpfc" target=11 lun=0;
name="sd" parent="lpfc" target=12 lun=0;
name="sd" parent="lpfc" target=13 lun=0;
name="sd" parent="lpfc" target=14 lun=0;
name="sd" parent="lpfc" target=15 lun=0;
name="sd" parent="lpfc" target=16 lun=0;
name="sd" parent="lpfc" target=17 lun=0;
name="sd" parent="lpfc" target=17 lun=1;
name="sd" parent="lpfc" target=17 lun=2;
name="sd" parent="lpfc" target=17 lun=3;

--增加部分
"sd.conf" 100 lines, 3022 characters
# vi lpfc.conf
"lpfc.conf" 276 lines, 10863 characters
#
# COPYRIGHT 2004, EMULEX CORPORATION
# 3333 Susan Street, Costa Mesa, CA 92626
#
# All rights reserved.  This computer program and related documentation
# is protected by copyright and distributed under licenses restricting
# its use, copying, distribution and decompilation.  This computer
# program and its documentation are CONFIDENTIAL and a TRADE SECRET
# of EMULEX CORPORATION.  The receipt or possession of this program
# or its documentation does not convey rights to reproduce or disclose
# its contents, or to manufacture, use, or sell anything that it may
# describe, in whole or in part, without the specific written consent
# of EMULEX CORPORATION.  Any reproduction of this program without
# the express written consent of EMULEX CORPORATION is a violation
# of the copyright laws and may subject you to criminal prosecution.
#
#
# Solaris LightPulse lpfc (SCSI) / lpfn (IP) driver: global initialized data.
#
# lpfc.conf 1.26 2004/03/15 11:41:22PST

# Verbosity:  only turn this flag on if you are willing to risk being
# deluged with LOTS of information.
# You can set a bit mask to record specific types of verbose messages:
#
# 0x1    ELS events
# 0x2    Device Discovery events
# 0x4    Mailbox Command events
# 0x8    Initialization events
# 0x10   Link Attention events
# 0x20   IP events
# 0x40   FCP events
# 0x80   Node table events
# 0x400  Miscellaneous events
# 0x800  SLI events
# 0x2000 IOCtl events
# 0xffff Log All Events
log-verbose=0x0;

# Setting log-only to 0 causes log messages to be printed on the
# console and to be logged to syslog (which may send them to the
# console again if it's configured to do so).
# Setting log-only to 1 causes log messages to go to syslog only.
log-only=1;

#
# +++ Variables relating to FCP (SCSI) support. +++
#
/top
# If set, nodev-holdio will hold all I/O errors on devices that disappear
# until they come back. Default is 0, return errors with no-device-delay.
nodev-holdio=0;

# If set, nodev-tmo will hold all I/O errors on devices that disappear
# until the timer [0 to 255 secs] expires. Default is 30, return errors
# with no-device-delay.
nodev-tmo=30;

# Use no-device-delay to delay FCP RSP errors and certain check conditions.
delay-rsp-err=0;

# Treat certain check conditions as an FCP error.
check-cond-err=0;

# num-iocbs [128 to 10240] - number of iocb buffers to allocate
num-iocbs=256;

# num-bufs [64 to 4096] - number of buffers to allocate
# Buffers are needed to support Fibre channel Extended Link Services.
# Also used for SLI-2 FCP buffers, one per FCP command, and Mailbox commands.
num-bufs=128;

# topology:  link topology for initializing the Fibre Channel connection.
#          0 = attempt loop mode, if it fails attempt point-to-point mode
#          2 = attempt point-to-point mode only
#          4 = attempt loop mode only
#          6 = attempt point-to-point mode, if it fails attempt loop mode
# Set point-to-point mode if you want to run as an N_Port.
# Set loop mode if you want to run as an NL_Port.
topology=2;

--由0更改为2

# Set a preferred ALPA for the adapter, only valid if topology is loop.
# lpfc0-assign-alpa=2;  Request ALPA 2 for lpfc0

# ip-class:  FC class (2 or 3) to use for the IP protocol.
ip-class=3;

# fcp-class:  FC class (2 or 3) to use for the FCP protocol.
fcp-class=3;

# Use ADISC for FCP rediscovery instead of PLOGI.
use-adisc=0;

# Extra IO timeout [0 to 255 secs] for fabrics
extra-io-tmo=0;

# Number of 4k STREAMS buffers [64 to 1024] to post to IP ring.
"lpfc.conf" 276 lines, 10863 characters
# reboot


修改配置文件后,重起主机生效

【问题记录】sbd——数据库突然hang住

早上客户反映服务器出现错误,得到如下错误反馈: BI00000000000020130716090500.xml20130716090522bjkjfedexCIQBMS报文入库出错.java.la...
  • sharqueen
  • sharqueen
  • 2013年07月16日 13:18
  • 2254

Linux存储在线管理(一)FC磁盘设备管理

本文转自:http://www.cactifans.org/linux/1071.html 转自EMC中文支持论坛 – https://community.emc.com/go/chinese 介...
  • msdnchina
  • msdnchina
  • 2015年02月08日 17:20
  • 2524

如何动态地给vSphere虚拟机模板注入信息

在做vSphere自动化安装过程中,遇到这样一个需求:将vCenter Server做成模板,在给用户自动化装好vSphere后, 下载vCenter Server模板并启动虚拟机,然后将vCente...
  • flyforfreedom2008
  • flyforfreedom2008
  • 2015年05月03日 15:55
  • 865

ESXi 5.x 命令行操作

网络 很多命令的 -h 都包含了详细的例子 esxcli network: 这是一个命令集, 包含了很多子命令 esxcli network nic list 查看网卡信息...
  • xiaoxinyu316
  • xiaoxinyu316
  • 2015年04月21日 17:06
  • 18300

高手对话:有关ESXi的主机缓存问题,值得收藏!

JAR提问: 大家都知道esxi 5支持用ssd盘做主机缓存,今天简单实验了一下,我用一块三星830 ssd盘,发现能够识别出驱动器类型为SSD。 并且用这块盘顺利启用了SSD主机缓存。 我的理...
  • loongsking
  • loongsking
  • 2015年02月09日 22:05
  • 9195

《转》VMware vSphere 5.1 学习系列之八:主机配置文件

目 录 一、    关于主机配置文件    1 二、    创建主机配置文件    2 创建主机配置文件    2 编辑主机配置文件    6 导出主机配置文件    9 导入主机配置...
  • qq_21398167
  • qq_21398167
  • 2016年01月23日 15:08
  • 811

华擎N3150J3160安装ESXi,然后组建家庭网络

大概分下面五个专题,今天先介绍第0个专题,也就是“组建完成的家庭网络介绍” 0. 组建完成的家庭网络介绍; 1. 华擎N3150/J3160安装ESXi; 2. 华擎N3150/J3160主板...
  • zhangsanm
  • zhangsanm
  • 2016年11月06日 12:12
  • 2624

vmware Esxi 5.0 忘记密码重置

参考文献: [1] http://daiheeq.blog.51cto.com/876282/1179197  VM ESXI 5.0忘记ROOT密码怎么办 [2] http://www.vm-h...
  • firenet1
  • firenet1
  • 2017年11月13日 18:18
  • 323

深入学习VMware vSphere---配置管理

VMware vSphere 学习笔记
  • Wee_Mita
  • Wee_Mita
  • 2017年02月18日 20:08
  • 333

PowerVM 高级功能——N_PIV

1.前言 IBM PowerVM 始终强调存储虚拟化、服务器虚拟化、网络等各种虚拟化!                                从而体现它的高可用,  灵活性  , 易操作性...
  • u012474376
  • u012474376
  • 2013年10月27日 16:39
  • 1444
内容举报
返回顶部
收藏助手
不良信息举报
您举报文章:Emulex光纤卡lpfc配置文件的修改
举报原因:
原因补充:

(最多只允许输入30个字)