实验拓扑图:
实验需求:
R1、R3是点对点
R1、R4R5是点到多点
全网互通
实验参考配置:
FR全互联
R2#show frame-relay route
Input Intf Input Dlci Output Intf Output Dlci Status
Serial0/0 301 Serial0/3 103 active
Serial0/1 401 Serial0/3 104 active
Serial0/2 501 Serial0/3 105 active
Serial0/3 103 Serial0/0 301 active
Serial0/3 104 Serial0/1 401 active
Serial0/3 105 Serial0/2 501 active
interface Serial0/0
no ip address
encapsulation frame-relay
serial restart-delay 0
clock rate 64000
frame-relay lmi-type cisco
frame-relay intf-type dce
frame-relay route 301 interface Serial0/3 103
!
interface Serial0/1
no ip address
encapsulation frame-relay
serial restart-delay 0
clock rate 64000
frame-relay lmi-type cisco
frame-relay intf-type dce
frame-relay route 401 interface Serial0/3 104
!
interface Serial0/2
no ip address
encapsulation frame-relay
serial restart-delay 0
clock rate 64000
frame-relay lmi-type cisco
frame-relay intf-type dce
frame-relay route 501 interface Serial0/3 105
!
interface Serial0/3
no ip address
encapsulation frame-relay
serial restart-delay 0
clock rate 64000
frame-relay lmi-type cisco
frame-relay intf-type dce
frame-relay route 103 interface Serial0/0 301
frame-relay route 104 interface Serial0/1 401
frame-relay route 105 interface Serial0/2 501
R1#
interface Loopback0
ip address 1.1.1.1 255.255.255.0
!
interface Serial0/0
no ip address
encapsulation frame-relay
serial restart-delay 0
!
interface Serial0/0.1 point-to-point
ip address 13.1.1.1 255.255.255.0
frame-relay interface-dlci 103
!
interface Serial0/0.2 multipoint
ip address 145.1.1.1 255.255.255.0
frame-relay map ip 145.1.1.4 104 broadcast
frame-relay map ip 145.1.1.5 105 broadcast
no frame-relay inverse-arp
router ospf 1
router-id 1.1.1.1
log-adjacency-changes
area 2 virtual-link 4.4.4.4
network 1.1.1.1 0.0.0.0 area 0
network 13.1.1.1 0.0.0.0 area 0
network 145.1.1.1 0.0.0.0 area 2
neighbor 5.5.5.5
neighbor 4.4.4.4
R4:
interface Loopback0
ip address 4.4.4.4 255.255.255.0
!
interface Serial0/0
ip address 145.1.1.4 255.255.255.0
encapsulation frame-relay
serial restart-delay 0
frame-relay map ip 145.1.1.1 401 broadcast
frame-relay map ip 145.1.1.5 401 broadcast
no frame-relay inverse-arp
!
interface Ethernet1/0
ip address 46.1.1.4 255.255.255.0
half-duplex
!
router ospf 1
router-id 4.4.4.4
log-adjacency-changes
area 2 virtual-link 1.1.1.1
network 4.4.4.4 0.0.0.0 area 1
network 46.1.1.4 0.0.0.0 area 1
network 145.1.1.4 0.0.0.0 area 2
neighbor 5.5.5.5
neighbor 1.1.1.1
!
R5:
interface Loopback0
ip address 5.5.5.5 255.255.255.0
!
interface Serial0/0
ip address 145.1.1.5 255.255.255.0
encapsulation frame-relay
serial restart-delay 0
frame-relay map ip 145.1.1.1 501 broadcast
frame-relay map ip 145.1.1.4 501 broadcast
no frame-relay inverse-arp
router ospf 1
router-id 5.5.5.5
log-adjacency-changes
network 5.5.5.5 0.0.0.0 area 2
network 145.1.1.5 0.0.0.0 area 2
neighbor 4.4.4.4
neighbor 1.1.1.1
R3:
interface Loopback0
ip address 3.3.3.3 255.255.255.0
!
interface Serial0/0
ip address 13.1.1.3 255.255.255.0
encapsulation frame-relay
ip ospf network point-to-point
serial restart-delay 0
!
router ospf 1
log-adjacency-changes
network 0.0.0.0 255.255.255.255 area 0
测试
R6# ping 1.1.1.1
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 1.1.1.1, timeout is 2 seconds:
!!!!!
最后看一下R6的路由表R6#show ip rou
1.0.0.0/32 is subnetted, 1 subnets
O IA 1.1.1.1 [110/75] via 46.1.1.4, 00:01:48, Ethernet0/0
3.0.0.0/32 is subnetted, 1 subnets
O IA 3.3.3.3 [110/139] via 46.1.1.4, 00:01:48, Ethernet0/0
4.0.0.0/32 is subnetted, 1 subnets
O 4.4.4.4 [110/11] via 46.1.1.4, 00:01:57, Ethernet0/0
6.0.0.0/24 is subnetted, 1 subnets
C 6.6.6.0 is directly connected, Loopback0
145.1.0.0/24 is subnetted, 1 subnets
O IA 145.1.1.0 [110/74] via 46.1.1.4, 00:01:57, Ethernet0/0
46.0.0.0/24 is subnetted, 1 subnets
C 46.1.1.0 is directly connected, Ethernet0/0
13.0.0.0/24 is subnetted, 1 subnets
O IA 13.1.1.0 [110/138] via 46.1.1.4, 00:01:51, Ethernet0/0
时间不早了,就简单把配置刷一下吧,谢谢朋友们。
感谢node!