CentOs 7中安装Vmware tools

step 1：

打开光盘，点击它，将VMWareTools-6.0.2.59824.tar.gz复制到home directory，進行解压缩。

[root@localhost ~ ]# tar zxvf VMwareTools-6.0.2-59824.tar.gz

step 2：
进入解压缩后的vmware-tools-distrib目录

[root@localhost ~ ]# cd vmware-tools-distrib/

Step 3：
执行vmware-install.pl安裝VMWare Tools

[root@localhost vmware-tools-distrib ]# ./vmware-install.pl

之后出现很多问题，都接受预设值 一直按enter即可，直到

最后出现以下信息：表示安装成功。

X Window System Version 7.1.1
Release Date: 12 May 2006
X Protocol Version 11, Revision 0, Release 7.1.1
Build Operating System: Linux 2.6.9-67.ELsmp i686 Red Hat, Inc.
Current Operating System: Linux localhost.localdomain 2.6.18-53.1.19.el5 #1 SMP Wed May 7 08:20:19 EDT 2008 i686
Build Date: 19 January 2008
Build ID: xorg-x11-server 1.1.1-48.26.el5_1.5 
         Before reporting problems, check http://wiki.x.org
         to make sure that you have the latest version.
Module Loader present
Markers: (--) probed, (**) from config file, (==) default setting,
         (++) from command line, (!!) notice, (II) informational,
         (WW) warning, (EE) error, (NI) not implemented, (??) unknown.
(++) Log file: "/tmp/vmware-config0/XF86ConfigLog.2977", Time: Fri Jun  6 15:14:32 2008
(++) Using config file: "/tmp/vmware-config0/XF86Config.2977"

X is running fine with the new config file.

FreeFontPath: FPE "unix/:7100" refcount is 2, should be 1; fixing.
Starting VMware Tools services in the virtual machine:
    Switching to guest configuration:                        [   確定   ]
    Guest filesystem driver:                                 [   確定   ]
    Mounting HGFS shares:                                    [失敗 ]
    Guest memory manager:                                    [   確定   ]
    Guest vmxnet fast network device:                        [   確定   ]
    Blocking file system:                                    [   確定   ]
    DMA setup:                                               [   確定   ]
    Guest operating system daemon:                           [   確定   ]

The configuration of VMware Tools 6.0.2 build-59824 for Linux for this running 
kernel completed successfully.

You must restart your X session before any mouse or graphics changes take 
effect.

You can now run VMware Tools by invoking the following command: 
"/usr/bin/vmware-toolbox" during an X server session.

To use the vmxnet driver, restart networking using the following commands: 
/etc/init.d/network stop
rmmod pcnet32
rmmod vmxnet
modprobe vmxnet
/etc/init.d/network start

To make use of the virtual printer, you will need to restart the CUPS service

Enjoy,

--the VMware team

重新启动CentOS，就可使用拖曳的方式传档了。


PS：主机与虚拟机共享文件方法

打开虚拟机设置（ctl＋D）＞选项Options＞共享文件夹 启用，然后在右边选择“总是启用”，添加你要共享的文件（夹）就OK了。。

打开/mnt/hgfs就看到共享的文件了。