Cisco 路由器交换机配置命令详解
1. 交换机支持的命令:
交换机基本状态 :
switch : ; ROM 状态, 路由器是 rommon>
hostname> ;用户模式
hostname# ;特权模式
hostname ( config ) # ;全局配置模式
hostname ( config-if ) # ;接口状态
交换机口令设置:
switch>enable ;进入特权模式
switch#config terminal ;进入全局配置模式
switch ( config ) #hostname ;设置交换机的主机名
switch ( config ) #enable secret xxx ;设置特权加密口令
switch ( config ) #enable password xxa ;设置特权非密口令
switch ( config ) #line console 0 ;进入控制台口
switch ( config-line ) #line vty 0 4 ;进入虚拟终端
switch ( config-line ) #login ;允许登录
switch ( config-line ) #password xx ;设置登录口令 xx
switch#exit ;返回命令
交换机 VLAN 设置:
switch#vlan database ;进入 VLAN 设置
switch ( vlan ) #vlan 2 ;建 VLAN 2
switch ( vlan ) #no vlan 2 ;删 vlan 2
switch ( config ) #int f0/1 ;进入端口 1
switch ( config-if ) #switchport access vlan 2 ;当前端口加入 vlan 2
switch ( config-if ) #switchport mode trunk ;设置为干线
switch ( config-if ) #switchport trunk allowed vlan 1 , 2 ;设置允许的 vlan
switch ( config-if ) #switchport trunk encap dot1q ;设置 vlan 中继
switch ( config ) #vtp domain ;设置发 vtp 域名
switch ( config ) #vtp password ;设置发 vtp 密码
switch ( config ) #vtp mode server ;设置发 vtp 模式
switch ( config ) #vtp mode client ;设置发 vtp 模式
交换机设置 IP 地址:
switch ( config ) #interface vlan 1 ;进入 vlan 1
switch ( config-if ) #ip address ;设置 IP 地址
switch ( config ) #ip default-gateway ;设置默认网关
switch#dir flash : ;查看闪存
交换机显示命令:
switch#write ;保存配置信息
switch#show vtp ;查看 vtp 配置信息
switch#show run ;查看当前配置信息
switch#show vlan ;查看 vlan 配置信息
switch#show interface ;查看端口信息
switch#show int f0/0 ;查看指定端口信息
2. 路由器支持的命令:
路由器显示命令:
router#show run ;显示配置信息
router#show interface ;显示接口信息
router#show ip route ;显示路由信息
router#show cdp nei ;显示邻居信息
router#reload ;重新起动
路由器口令设置:
router>enable ;进入特权模式
router#config terminal ;进入全局配置模式
router ( config ) #hostname ;设置交换机的主机名
router ( config ) #enable secret xxx ;设置特权加密口令
router ( config ) #enable password xxb ;设置特权非密口令
router ( config ) #line console 0 ;进入控制台口
router ( config-line ) #line vty 0 4 ;进入虚拟终端
router ( config-line ) #login ;要求口令验证
router ( config-line ) #password xx ;设置登录口令 xx
router ( config ) # ( Ctrl+z ) ; 返回特权模式
router#exit ;返回命令
路由器配置:
router ( config ) #int s0/0 ;进入 Serail 接口
router ( config-if ) #no shutdown ;激活当前接口
router ( config-if ) #clock rate 64000 ;设置同步时钟
router ( config-if ) #ip address ;设置 IP 地址
router ( config-if ) #ip address second ;设置第二个 IP
router ( config-if ) #int f0/0.1 ;进入子接口
router ( config-subif.1 ) #ip address ;设置子接口 IP
router ( config-subif.1 ) #encapsulation dot1q ;绑定 vlan 中继协议
router ( config ) #config-register 0x2142 ;跳过配置文件
router ( config ) #config-register 0x2102 ;正常使用配置文件
router#reload ;重新引导
路由器文件操作:
router#copy running-config startup-config ;保存配置
router#copy running-config tftp ;保存配置到 tftp
router#copy startup-config tftp ;开机配置存到 tftp
router#copy tftp flash : ;下传文件到 flash
router#copy tftp startup-config ;下载配置文件
ROM 状态:
Ctrl+Break ;进入 ROM 监控状态
rommon>confreg 0x2142 ;跳过配置文件
rommon>confreg 0x2102 ;恢复配置文件
rommon>reset ;重新引导
rommon>copy xmodem : flash : ;从 console 传输文件
rommon>IP_ADDRESS=10.65.1.2 ;设置路由器 IP
rommon>IP_SUBNET_MASK=255.255.0.0 ;设置路由器掩码
rommon>TFTP_SERVER=10.65.1.1 ;指定 TFTP 服务器 IP
rommon>TFTP_FILE=c2600.bin ;指定下载的文件
rommon>tftpdnld ;从 tftp 下载
rommon>dir flash : ;查看闪存内容
rommon>boot ;引导 IOS
静态路由:
ip route ;命令格式
router ( config ) #ip route 2.0.0.0 255.0.0.0 1.1.1.2 ;静态路由举例
router ( config ) #ip route 0.0.0.0 0.0.0.0 1.1.1.2 ;默认路由举例
动态路由:
router ( config ) #ip routing ;启动路由转发
router ( config ) #router rip ;启动 RIP 路由协议。
router ( config-router ) #network ;设置发布路由
router ( config-router ) #negihbor ;点对点帧中继用。
帧中继命令:
router ( config ) #frame-relay switching ;使能帧中继交换
router ( config-s0 ) #encapsulation frame-relay ;使能帧中继
router ( config-s0 ) #fram-relay lmi-type cisco ;设置管理类型
router ( config-s0 ) #frame-relay intf-type DCE ;设置为 DCE
router ( config-s0 ) #frame-relay dlci 16 ;
router ( config-s0 ) #frame-relay local-dlci 20 ;设置虚电路号
router ( config-s0 ) #frame-relay interface-dlci 16 ;
router ( config ) #log-adjacency-changes ;记录邻接变化
router ( config ) #int s0/0.1 point-to-point ;设置子接口点对点
router#show frame pvc ;显示永久虚电路
router#show frame map ;显示映射
基本访问控制列表:
router ( config ) #access-list permit|deny
router ( config ) #interface ; default : deny any
router ( config-if ) #ip access-group in|out ; defaultut
例 1 :
router ( config ) #access-list 4 permit 10.8.1.1
router ( config ) #access-list 4 deny 10.8.1.0 0.0.0.255
router ( config ) #access-list 4 permit 10.8.0.0 0.0.255.255
router ( config ) #access-list 4 deny 10.0.0.0 0.255.255.255
router ( config ) #access-list 4 permit any
router ( config ) #int f0/0
router ( config-if ) #ip access-group 4 in
扩展访问控制列表:
access-list permit|deny icmp [type]
access-list permit|deny tcp [port]
例 2 :
router ( config ) #access-list 101 deny icmp any 10.64.0.2 0.0.0.0 echo
router ( config ) #access-list 101 permit ip any any
router ( config ) #int s0/0
router ( config-if ) #ip access-group 101 in
例 3 :
router ( config ) #access-list 102 deny tcp any 10.65.0.2 0.0.0.0 eq 80
router ( config ) #access-list 102 permit ip any any
router ( config ) #interface s0/1
router ( config-if ) #ip access-group 102 out
删除访问控制例表:
router ( config ) #no access-list 102
router ( config-if ) #no ip access-group 101 in
路由器的 nat 配置
Router ( config-if ) #ip nat inside ;当前接口指定为内部接口
Router ( config-if ) #ip nat outside ;当前接口指定为外部接口
Router ( config ) #ip nat inside source static [p] [port]
Router ( config ) #ip nat inside source static 10.65.1.2 60.1.1.1
Router ( config ) #ip nat inside source static tcp 10.65.1.3 80 60.1.1.1 80
Router ( config ) #ip nat pool p1 60.1.1.1 60.1.1.20 255.255.255.0
Router ( config ) #ip nat inside source list 1 pool p1
Router ( config ) #ip nat inside destination list 2 pool p2
Router ( config ) #ip nat inside source list 2 interface s0/0 overload
Router ( config ) #ip nat pool p2 10.65.1.2 10.65.1.4 255.255.255.0 type rotary
Router#show ip nat translation
rotary 参数是轮流的意思,地址池中的 IP 轮流与 NAT 分配的地址匹配。
overload 参数用于 PAT 将内部 IP 映射到一个公网 IP 不同的端口上。
外部网关协议配置
routerA ( config ) #router bgp 100
routerA ( config-router ) #network 19.0.0.0
routerA ( config-router ) #neighbor 8.1.1.2 remote-as 200
配置 PPP 验证:
RouterA ( config ) #username password
RouterA ( config ) #int s0
RouterA ( config-if ) #ppp authentication {chap|pap}
3.PIX 防火墙命令
Pix525 ( config ) #nameif ethernet0 outside security0 ;命名接口和级别
Pix525 ( config ) #interface ethernet0 auto ;设置接口方式
Pix525 ( config ) #interface ethernet1 100full ;设置接口方式
Pix525 ( config ) #interface ethernet1 100full shutdown
Pix525 ( config ) #ip address inside 192.168.0.1 255.255.255.0
Pix525 ( config ) #ip address outside 133.0.0.1 255.255.255.252
Pix525 ( config ) #global ( if_name ) natid ip-ip ;定义公网 IP 区间
Pix525 ( config ) #global ( outside ) 1 7.0.0.1-7.0.0.15 ;例句
Pix525 ( config ) #global ( outside ) 1 133.0.0.1 ;例句
Pix525 ( config ) #no global ( outside ) 1 133.0.0.1 ;去掉设置
Pix525 ( config ) #nat ( if_name ) nat_id local_ip [netmark]
Pix525 ( config ) #nat ( inside ) 1 0 0
内网所有主机( 0 代表 0.0.0 .0 )可以访问 global 1 指定的外网。
Pix525 ( config ) #nat ( inside ) 1 172.16.5.0 255.255.0.0
内网 172.16.5.0/16 网段的主机可以访问 global 1 指定的外网。
Pix525 ( config ) #route if_name 0 0 gateway_ip [metric] ;命令格式
Pix525 ( config ) #route outside 0 0 133.0.0.1 1 ;例句
Pix525 ( config ) #route inside 10.1.0.0 255.255.0.0 10.8.0.1 1 ;例句
Pix525 ( config ) #static ( inside , outside ) 133.0.0.1 192.168.0.8
表示内部 ip 地址 192.168.0.8 ,访问外部时被翻译成 133.0.0.1 全局地址。
Pix525 ( config ) #static ( dmz , outside ) 133.0.0.1 172.16.0.8
中间区域 ip 地址 172.16.0.8 ,访问外部时被翻译成 133.0.0.1 全局地址。