配置直连二层组网直接转发示例
1.接入交换机1口属于vlan100
命名access
Vlan batch 100 101
interface g0/0/1
port link-type trunk
port trunk pvid vlan 100
port trunk allow-pass vlan 100 to 101
2口
port link-type trunk
port trunk allow-pass vlan 100 to 101
2.在AC
命名control
Vlan batch 100 101
vlanif 101
ip address 10.23.101.1 24
vlanif 100
ip address 10.23.100.1 24
g0/0/1
port link-type trunk
port trunk allow-pass vlan 100 to 101
g0/0/2
port link-type access
port access default vlan 101
dhcp enable
interface vlanif 101
dhcp select interface
dhcp server excluded-ip-address 10.23.101.2
interface vlanif100
dhcp select interface
q
ip route-static 0.0.0.0 0.0.0.0 10.23.101.2
在AC
dis ap all
wlan
ap-group name a 创建组a
q
创建策略模板:
regulatory-domain-prefile name aaa名称随便定义
q
ap-group name a 进入组
regulatory-domain-prefile aaa将策略加进去
q
AC源接口:
capwap source interface vlanif 100
wlan
ap auth-mode mac-auth 认证MAC
绑定:
ap-id 0 ap-mac 00e0-fcc9-49f0
去AP display interface g0/0/0 找到hardware复制到此
ap-name area-1随便定义名称
ap-group a 进行绑定将以上步骤
q
3.配置安全策略:
wlan
security-profile name huawei
security wpa-wpa2 psk pass-phrase a1234567 aes采用aes加密
配置模板ssid
wlan
ssid-profile name huawei
ssid HUAWEI
创建VAP模板
vap-profile name huawei
forward-mode direct-forward 直接转发
tunnel是隧道转发,改变转发模式之后需要重新连接一下网络才可ping10.23.101.2通
service-vlan vlan-id 101
ssid-profile huawei
security-profile huawei
配置射频
wlan
ap-group name a
vap-profile huawei wlan 1 radio 0
vap-profile huawei wlan 1 radio 1
命令执行完会出现射频圈
关闭射频信道和频率自动调优
rrm-profile name default
calibrate auto-channel-select disable
calibrate auto-txpower-select disable
配置射频信道和功率
ap-id 0
radio 0
channel 20mhz 6
eirp 127
radio 1
channel 20mhz 149
eirp 127
打开PC连接两种信号
最终结果
[control]dis ap all
Info: This operation may take a few seconds. Please wait for a moment.done.
Total AP information:
nor : normal [1]
--------------------------------------------------------------------------------
---------------
ID MAC Name Group IP Type State STA Uptim
e
--------------------------------------------------------------------------------
---------------
0 00e0-fcc9-49f0 area-1 a 10.23.100.223 AP3030DN nor 2 2H:53
M:7S
--------------------------------------------------------------------------
nor表示AP正常上线
显示ON时表示AP对应的射频上VAP创建成功
[control-wlan-view]dis vap ssid HUAWEI
Info: This operation may take a few seconds, please wait.
WID : WLAN ID
---------------------------------------------------------------------------
AP ID AP name RfID WID BSSID Status Auth type STA SSID
---------------------------------------------------------------------------
0 area-1 0 1 00E0-FCC9-49F0 ON WPA/WPA2-PSK 2 HUAWEI
0 area-1 1 1 00E0-FCC9-4A00 ON WPA/WPA2-PSK 0 HUAWEI
---------------------------------------------------------------------------
Total: 2
业务需求
企业用户通过WLAN接入网络,直接转发
组网需求
AC组网方式:直连二层组网
DHCP部署方式:AC作为dhcp服务器为AP和STA分配ip地址
数据规划
AP管理vlan100;sta业务为vlan101
AC源接口ip地址:vlanif100 10.23.100.1
AP组:
名称:a
引用模板:域管理模板aaa(策略模板),VAP模板huawei
ssid模板:
名称:huawei
Ssid名称:HUAWEI
安全模板:
名称huawei 密码:a1234567
Vap 模板:
名称:huawei
转发模式:直接转发
业务vlan:vlan101
引用模板:ssid模板huawei,安全模板huawei
配置之后的结果: