项目中的一台应用服务器,由于存放比较大的地图数据,硬盘需要扩容。服务器是2U的Dell服务器,操作系统使用日文Redhat5.3系统。原本配置两块500G的SCSI硬盘,磁盘阵列做了RAID1,现在需要增容1T。
一、硬件安装及RAID1增加。准备好两块型号相同的SCSI硬盘,装入硬盘插槽。启动系统,进入BIOS,在磁盘阵列配置中,检测识别,新追加的两块1T硬盘。然后,追加一个新的Array,具体操作这里就不做详细说明了。
二、硬盘的分区及最终挂载。
1、确认做好的RAID1设备是否存在。(原有的系统的设备是sdb)
执行命令: dmesg |grep sd
[root@ODCDTCFW /]# dmesg |grep sd
SCSI device sda: 1952448512 512-byte hdwr sectors (999654 MB)
2、查询设备信息。
执行设备信息查询命令:fdisk -l
Disk /dev/sda: 999.6 GB, 999653638144 bytes
255 heads, 63 sectors/track, 121534 cylinders
Units = シリンダ数 of 16065 * 512 = 8225280 bytes
ディスク /dev/sda は正常な領域テーブルを含んでいません
Disk /dev/sdb: 499.5 GB, 499558383616 bytes
255 heads, 63 sectors/track, 60734 cylinders
Units = シリンダ数 of 16065 * 512 = 8225280 bytes
デバイス Boot Start End Blocks Id System
/dev/sdb1 * 1 382 3068383+ 83 Linux
/dev/sdb2 383 2294 15358140 83 Linux
/dev/sdb3 2295 3441 9213277+ 82 Linux swap / Solaris
/dev/sdb4 3442 60734 460206022+ 5 拡張領域
/dev/sdb5 3442 4206 6144831 83 Linux
/dev/s
一、硬件安装及RAID1增加。准备好两块型号相同的SCSI硬盘,装入硬盘插槽。启动系统,进入BIOS,在磁盘阵列配置中,检测识别,新追加的两块1T硬盘。然后,追加一个新的Array,具体操作这里就不做详细说明了。
二、硬盘的分区及最终挂载。
1、确认做好的RAID1设备是否存在。(原有的系统的设备是sdb)
执行命令: dmesg |grep sd
[root@ODCDTCFW /]# dmesg |grep sd
SCSI device sda: 1952448512 512-byte hdwr sectors (999654 MB)
2、查询设备信息。
执行设备信息查询命令:fdisk -l
Disk /dev/sda: 999.6 GB, 999653638144 bytes
255 heads, 63 sectors/track, 121534 cylinders
Units = シリンダ数 of 16065 * 512 = 8225280 bytes
ディスク /dev/sda は正常な領域テーブルを含んでいません
Disk /dev/sdb: 499.5 GB, 499558383616 bytes
255 heads, 63 sectors/track, 60734 cylinders
Units = シリンダ数 of 16065 * 512 = 8225280 bytes
デバイス Boot Start End Blocks Id System
/dev/sdb1 * 1 382 3068383+ 83 Linux
/dev/sdb2 383 2294 15358140 83 Linux
/dev/sdb3 2295 3441 9213277+ 82 Linux swap / Solaris
/dev/sdb4 3442 60734 460206022+ 5 拡張領域
/dev/sdb5 3442 4206 6144831 83 Linux
/dev/s