端口镜像技术
概述
端口镜像技术其实就是一种监控网络流量的方法。
这种技术以生活场景来,你的网络就像一个繁忙的十字路口,有很多车(数据包)来来往往。端口镜像就是在不影响这些车正常行驶的情况下,偷偷复制某些车(特定端口的数据流量)到一个专门的观察点(镜像端口),让网络管理员能够观察和分析这些车的行为。
配置指令
Cisco(思科):
# 首先,定义一个监控会话,将流量镜像到指定的端口
monitor session 1 source interface FastEthernet0/1 both
monitor session 1 destination interface FastEthernet0/2
# 解释:
# source interface FastEthernet0/1 both 表示对接口FastEthernet0/1上的所有流量进行镜像
# destination interface FastEthernet0/2 表示将镜像的流量发送到FastEthernet0/2接口
Huawei:
[Huawei] port-mirroring group 1 local-port GigabitEthernet 0/0/1 | |
[Huawei] port-mirroring group 1 monitor-port GigabitEthernet 0/0/2 |
Juniper:
进入系统视图:
system
进入需要配置端口镜像的接口视图(例如,源端口):
edit interface ge-0/0/1
启用端口镜像功能并指定目的端口:
set monitor session destination interface ge-0/0/2
保存配置并退出接口视图:
top
Dell/Force10:
S1# configure terminal | |
S1(config)# span session 1 source interface ethernet 1/0/1 | |
S1(config)# span session 1 destination interface ethernet 1/0/2 |
Brocade:
config t
interface interface-list
port-mirroring to {interface-name | both} [override]
end
其中:
interface interface-list 指定需要镜像的源端口。interface-list 可以是单个端口或端口范围。
port-mirroring to {interface-name | both} 指定镜像的目的地。interface-name 是目的端口的名称,both 表示镜像到本地和远程。
override 是可选的,用于指定是否覆盖已有的端口镜像配置。
例如,如果您想要将端口FastEthernet1/1上的流量镜像到FastEthernet1/2,可以使用以下配置:
config t
interface FastEthernet1/1
port-mirroring to FastEthernet1/2
end
这将配置FastEthernet1/1端口的流量镜像到FastEthernet1/2端口。
Arista:
Arista的EOS操作系统与Cisco的命令非常相似。
Switch(config)# monitor session 1 source interface Ethernet1 | |
Switch(config)# monitor session 1 destination interface Ethernet2 |
HP Enterprise:
HP的Comware OS可能使用与Huawei类似的命令。
[HP] mirroring-group 1 local-port GigabitEthernet1/0/1 | |
[HP] mirroring-group 1 monitor-port GigabitEthernet1/0/2 |
Aruba/HPE:
进入全局配置模式
<HPE> system-view
# 配置源端口,这里以端口10为例
[HPE] interface 10
# 退出端口配置模式
[HPE-Interface10] quit
# 配置目的端口,这里以端口20为例
[HPE] interface 20
# 启用端口镜像模式
[HPE-Interface20] port-mirroring to monitor-port
# 退出目的端口配置模式
[HPE-Interface20] quit
# 创建或进入监控端口配置视图,如果端口21可用,则使用端口21,否则选择其他端口
[HPE] interface 21
# 在监控端口上配置端口镜像
[HPE-Interface21] port-mirroring monitor-port
# 退出监控端口配置模式
[HPE-Interface21] quit