MULTIGIG RT 2, RT 2-R, and RT 3 Signal Connectors .pdf
VPX 连接器资料
This specification covers the requirements for application of MULTIGIG RT 2, RT 2-R, and RT 3
connectors used to interconnect printed circuit (pc) boards. RT 2 and RT 2-R connectors are compliant to
the VITA 46 standard for VPX architecture, and TE supports other custom and non-standard MULTIGIG
variations. RT 3 is interface compatible with RT 2 and RT 2-R, but utilizes different board footprints with
smaller compliant pins and plated thru holes to achieve 16 to 25 Gbps data rates. The connectors consist
of end-to-end stackable modules, available in vertical receptacles (backplane application) and right-angle
plugs (daughtercard application). Half and full-size connector modules are used within slots of a
backplane/plug-in card application. The VITA 46 standard defines connector requirements and OpenVPX
standard slot configurations are defined in VITA 65.0 and 65.1.
VITA46.10 RTM.pdf
VITA46.10 RTM ,关于VPX RTM 背板后连接技术。
74hc+4000.zip
74和4000系列逻辑电路目录
型号-功能对照表
便于快速查找型号、设计选型
CCD4096x4096DataSheetRevB.pdf
s a 4096(H) x 4097(V) solid state Charge Coupled
Device (CCD) full frame sensor. The CCD is intended for
advanced scientific, space, industrial, and commercial digital
imaging applications. The CCD486 active area is organized as an
array of 4096 horizontal by 4097 vertical imaging elements. The
pixel pitch is 15µm with a 100% fill factor. For dark reference,
each readout line is preceded by 18 dark pixels. The imager is
available in front-illuminated as well as back-illuminated
configuration. A split readout architecture has been adopted to
facilitate high data rates with simultaneous readout from four
output ports, and provides the flexibility to read out the entire
image frame from two output ports, or from a single output port to
simplify the drive electronics requirements
ccd6161_data_sheet_january_2013.pdf
60mm方形CCD,不是CMOS喔。
a 4096(H) x 4096(V) solid state Charge
Coupled Device (CCD) Full Frame sensor. The CCD is intended
for advanced scientific, space, industrial, and commercial
digital imaging applications. The CCD6161 active area is
organized as an array of 4096 horizontal by 4096 vertical
imaging elements.
In addition to 4096(H) x 4096(V) imaging elements there
are 8 peripheral columns on left and right edges of the imaging
area to improve non-uniformity at t h e edges. These 16
peripheral columns are not connected to t h e serial register.
There are 32 isolation rows on top and bottom of the imaging
area and these 64 isolation rows are covered by metal, making
the total array 4112(H) x 4160(V). The pixel pitch is 15µm with
a 100% fill factor. For dark reference, each readout line is
preceded by 18 dark pixels. A split readout architecture has
been adopted to facilitate high data rates with simultaneous
readout from four output ports, and provides the flexibility to
read out the entire image frame from two output ports, or from a
single output port to simplify the drive electronics requirements.
data_sheet_ccd9216x9216.pdf
A 9216 x 9216 active element solid state Charge Coupled
Device (CCD) Full Frame sensor. The CCD is intended for advanced
scientific, space, and aerial reconnaissance applications. The CCD 595 is
organized as an array of 9216 horizontal by 9216 vertical imaging
elements. The pixel pitch is 8.75um with a 100% fill factor. Three-phase
clocking is employed in the imaging area with two-phase clocking in the
serial readout registers. Image readout is performed via 4 serial registers
containing 19 isolation rows between imaging and readout sections. The
imaging array can be clocked unidirectional (4-output configuration) or bidirectional (8-output configuration). The imaging area segments are split
in mid-array for the latter configuration. To maximize the
exposure/readout cycle rate, concurrent array and serial register clocking
is utilized. Fast transfer clocking between the array and serial registers is
accomplished with strapped transfer gates that load each line in less than
five microseconds.
ATI_FT_Catalog.pdf
The Force/Torque (F/T) sensor system measures the full
six components of force and torque (Fx, Fy, Fz, Tx, Ty, Tz)
using a monolithic instrumented transducer. The F/T
transducer uses silicon strain gages for excellent noise
immunity. The use of silicon gages allows the F/T
transducer to have high stiffness and increased overload
protection. All transducer models are available with Net
F/T, DAQ F/T, or Controller F/T interfaces
PCI Express Rev_2.0.zip
设计PICe卡的必要资料
1)PCI Express® Card Electromechanical Specification Revision 2.0 April 11, 2007
2)PCI Express® Base Specification Revision 5.0 Version 1.0 22 May 2019
《工业机器人设计指南》.pdf
机器人是一个非常复杂的系统,在机电一体化和功能性以及
电气方面存在许多设计挑战。在实现一个可行的工作系统
前,您需要解决了这些挑战或做出一些决定。
利用机器人系统的所有不同技术特性,德州仪器 (TI) 的模拟
和嵌入式技术提供了许多不同的产品和设计,可以帮助解决
与机器人有关的问题,实现智能、自主和协作机器人的开发。
这本电子书汇集了技术文章、白皮书和应用手册,它们均包
括有助于帮您设计下一个机器人系统的技术。
WX820LM.pdf 5-in-1 Multi Sander 5合1砂磨机
Use only good quality sandpaper. The sandpaper controls the sanding efficiency, not the amount of force you apply to the tool. Excessive force will reduce the sanding efficiency and cause motor overload. Replacing the sandpaper regularly will maintain optimum sanding efficiency.
precision-3630-workstation_users-guide_zh-cn.pdf
precision-3630-workstation_users-guide_zh-cn 用户手册,这个不太容易找到啊
大众汽车故障编码表00000-00240
00000 没有查询到任何故障
00001 制动器控制单元
00002 变速器控制单元
00003 控制单元
00224 碟型天线需要重新校准
00237 ABS 电磁阀: 左前 N59
00238 ABS 电磁阀: 右前 N58
00239 ABS 电磁阀: 左后 N57
00240 ABS 电磁阀: 右后 N56 ">00000 没有查询到任何故障
00001 制动器控制单元
00002 变速器控制单元
00003 控制单元
00224 碟型天线需要重新校准
00237 ABS 电磁阀: 左前 N59
00238 ABS 电磁阀: 右前 N58
00239 ABS 电磁阀: 左后 N57
00240 ABS 电磁阀: 右后 N5 [更多]
Sony 1/1.8 CMOS Sensor
CMOS sensors are now widely used in
cellular phones and other mobile devices,
and as a result, sales of these devices have
been increasing rapidly. Furthermore,
demand for CMOS sensors has been increasing
in fields that require high-speed
imaging functions, such as digital singlelens
reflex cameras.
CSR蓝牙芯片选型参考
The BlueCore line of Bluetooth products for CSR integrate a radio and baseband along with peripherals to match your
application requirements. Variants are available with integrated ROM or flash, Multimedia versions with integrated DSP and
stereo codec, or Plug-n-Go with integrated balun, filter and matching.
BlueCore 3: CSR’s complete v1.2 Bluetooth solution including eSCO (extended Synchronous Connections), which allows
for retransmissions of dropped packets, allowing for a cleaner, better sound out of your Bluetooth device.
BlueCore 4: CSRs EDR (Enhanced Data Rate) v2.0 Bluetooth solution, it offers backwards compatibility with v1.1 and v1.2
Bluetooth devices. External Flash, ROM, Plug-n-Go and Headset versions are available to match your application. Offers
up to 3 times the data rate as previous versions of Bluetooth with lower power consumption.
BlueCore 5: series offers the latest generation technology, offering compatibility with the next generation Bluetooth spec,
如何开发蓝牙芯片_360综合搜索
LabPro单芯片蓝牙开发工具简介 - 豆丁网
labpro,开发,单芯片,蓝牙,LabPro,PAN,工具,应用程序,CSR,BlueCore,样例,eadset,星光第一季,IT计算机 IT计算机
开发文档 LabPro单芯片蓝牙开发工具简介
程序修改器 HA-eXeScope650 破解码.txt
程序修改器 HA-eXeScope650 破解码.txt
1n457稳压二极管
常用的二极管DataSheet:
1N457
1N4728A 1N4764A1N4728A 1N4764A1N4728A 1N4764A1N4728A 1N4764A
1N4728A 1N4764A1N4728A 1N4764A1N4728A 1N4764A1N4728A 1N4764A
OLED 资源列表 共若干个
资料 OLED 资源列表
1,三星
2,LG
3,夏普
4,其他
5,可以再丰富
6,回到原来状态
中高压多层片状陶电容器
中高压多层片状陶瓷电容器是在多
层片状陶瓷电容器的工艺技术、设备基
础上,通过采用特殊设计制作出来的一
种具有良好高压可靠性的产品,该产品
适合于表面贴装,适合于多种直流高压
线路,可以有效的改善电子线路的性能。
飞利浦SAA7154专业视频解码器
The SAA7154 provides a complete and versatile decoding
solution for high-performance applications such as LCD
displays, TVs/monitors, LCD projectors, automotive display
modules and PC peripherals like TV boxes. This highlyintegrated
system solution offers outstanding fl exibility
and unsurpassed picture quality.