 |
 | 呢称：xuwangzhiye 文章(15) 访问(28186) 评论(2) 投票(0) 订阅本博  | |
| 全部博文： 2008年 - 11月 10月 | 查看全部博文 | |
   博客首页 | ||
start.S是pmon遮盖整个源码编译后生成的gzrom.bin文件过程中第一个被链接的文件,整个程序的开始就从start.S开始.
整个程序的第一行代码是从start开始的.
#ifndef _KERNEL
#define _KERNEL
#endif
#include <asm.h>
#include <regnum.h>
#include <cpu.h>
#include <pte.h>
#include "pmon/dev/ns16550.h"
#include "target/prid.h"
#include "target/sbd.h"
#include "target/bonito.h"
#include "target/via686b.h"
#include "target/i8254.h"
#include "target/isapnpreg.h"
//#define DEBUG_LOCORE
/***(qiaochong) memeory initialization use macro,not smbbus ***/
/*bit 31: DDR配置结束标志，1表示结束，只读*/
#define DDR_DQS_SELECT (0<<30) /*bit 30 选择数据来源，0: 双沿采样；1：DQS采样*/
#define DDR_DIMM_DIC (1<<29) /*bit 29 标识DIMM_slot0是否插有内存条。
0：无；1：有；*/
#define DDR_DIMM_MODULE_NUM (3<<27) /*bit 28:27 DIMM0/DIMM1上MOUDLE的数目：
2’b00：DIMM1: 1; DIMM0: 1
2’b01：DIMM1: 1; DIMM0: 2
2’b10：DIMM1: 2; DIMM0: 1
2’b11：DIMM1: 2; DIMM0: 2
*/
#define DDR_IS_SEQ (1<<26) /*bit 26 义突发式读写时的块内顺序，
1’b0：顺序；1’b1：交替，现在只支持交替方式*/
#define DDR_TYPE (5<<22) /*bit 25:22 表2：DDR 控制器所支持的DDR SDRAM 计芯片类型
BITS Density Org. Row Addr. Col Addr.
0000 64Mb 16Mb X 4 DA[11:0] DA[9:0]
128Mb 16Mb X 8
0001 64Mb 8Mb X 8 DA[11:0] DA[8:0]
128Mb 8Mb X 16
0010 64Mb 4Mb X 16 DA[11:0] DA[7:0]
0011 128Mb 32Mb X 4 DA[11:0] DA[11],DA[9:0]
0100 256Mb 64Mb X 4 DA[12:0] DA[11],DA[9:0]
512Mb 64Mb X 8
0101 256Mb 32Mb X 8 DA[12:0] DA[9:0]
512Mb 32Mb X 16
0110 256Mb 16Mb X 16 DA[12:0] DA[8:0]
0111 512Mb 128Mb X 4 DA[12:0] DA[12:11],DA[9:0]
1000 1Gb 256Mb X 4 DA[13:0] DA[12:11],DA[9:0]
1001 1Gb 128Mb X 8 DA[13:0] DA[11],DA[9:0]
1010 1Gb 64Mb X 16 DA[13:0] DA[9:0]
*/
#define DDR_tREF (100<<10) /*bit 21:10 SDRAM刷新操作之间计数（主频100MHz）：
780 7.8us
1560 15.6us
SDRAM刷新操作之间计数（主频133MHz）：
1040 7.8us
2080 15.6us
SDRAM刷新操作之间计数（主频166MHz）：
1300 7.8us
2600 15.6us
*/
#define DDR_TRCD (1<<9) /*bit 9 行地址有效到列地址有效之间需经过的计数
1’b0 2 cycles（DDR100）
1’b1 3 cycles（DDR266、DDR333）*/
#define DDR_TRPC (1<<7) /*bit 8:7 AUTO_REFRESH到ACTIVE之间需经过的计数
2’b00 Null
2’b01 8 cylces （DDR100）
2’b10 10 cycles（DDR266）
2’b11 12 cycles（DDR333）
*/
#define DDR_TRAS (0<<6) /*bit 6 ACTIVE到PRECHARGE之间需经过的计数
1’b0 5 cycles（DDR100）
1’b1 7 cycles（DDR266、DDR333）
*/
#define DDR_TCAS (3<<4) /*bit 5:4 从读命令到第一个数据到来需经过的计数
2’b00 1.5 cycles
2’b01 2 cycles
2’b10 2.5 cycles
2’b11 3 cycles
*/
#define DDR_TWR (0<<3) /*bit 3 写操作最后一个数据到PRECHARGE之间需经过的计数
1’b0 2 cycles（DDR100）
1’b1 3 cycles（DDR266、DDR333）
*/
#define DDR_TRP (1<<2) /*bit 2 PRECHARGE命令执行时间计数
1’b0 2 cycles（DDR100）
1’b1 3 cycles（DDR266、DDR333）
*/
#define DDR_TRC (1<<0) /*bit 1:0 ACTIVE与ACTIVE/AUTO_REFRESH命令之间计数
2’b00 Null
2’b01 7 cycles（DDR100）
2’b10 9 cycles（DDR266）
2’b11 10cycles（DDR333）
注（由于precharge和ras cas的延时加起来正好满足这个延时，所以在DDR控制器里没有具体考虑这个参数）
*/
#define sdcfg_DATA DDR_DQS_SELECT|DDR_DIMM_DIC|DDR_DIMM_MODULE_NUM|DDR_IS_SEQ|DDR_TYPE|DDR_tREF|DDR_TRCD|DDR_TRPC|DDR_TRAS|DDR_TCAS|DDR_TWR|DDR_TRP|DDR_TRC
#ifdef DEBUG_LOCORE
#define TTYDBG(x) \
.rdata;98: .asciz x; .text; la a0, 98b; bal stringserial; nop
#else
#define TTYDBG(x)
#endif
#define PRINTSTR(x) \
.rdata;98: .asciz x; .text; la a0, 98b; bal stringserial; nop
#define CONFIG_CACHE_64K_4WAY 1
#define tmpsize s1
#define msize s2
#define bonito s4
#define dbg s5
#define sdCfg s6
#define CP0_CONFIG $16
#define CP0_TAGLO $28
#define CP0_TAGHI $29
#define DDR100 0x1d441091
/*
#define DDR100 0x0c011091*/
#define DDR266 0x0410435e
#define DDR300 0x041453df
#define DDR_DQ 0xbff00030 /* zgj */
* Register usage:
*
* s0 link versus load offset, used to relocate absolute adresses.
* s1 free
* s2 memory size.
* s3 free.
* s4 Bonito base address.
* s5 dbg.
* s6 sdCfg.
* s7 rasave.
* s8 L3 Cache size.
*/
/*?为什么有这种约定*/
/*上面说明的在本程序中子程序寄存器s0-s8(寄存器毫16-23,30)的默认使用规则*/
.set noreorder /*防止汇编器为了在分支延迟槽中填充有用指令而打乱代码次序*/
.globl _start/*声明__start start __main为全局地址*/
.globl start
.globl __main
_start:
start:
.globl stack /*声明stack为全局变量,并设置其地址为PMON起始代码后面16K的地方,MIPS体系结构的cpu上电执行的第一条指令位于物理地址0X1fc00000的地方开始执行,此处被北桥映射为flash的0地址,但start的值在最终生成的rom镜像gzrom中是由链接时候指定的地址0X81000000(参照/zloader/Makefile.inc GZROMSTARTADDR?=0xffffffff81000000),那么stack的值为0X80ffd000,注意这里虽然设置了栈在ram空间,但并没有使用,因为在Kseg0中,cache还没有设置,并且这里提到的地址是逻辑地址,而不关物理地址是如何映射的,mips体系结构是不能直接物理寻址的,总要从逻辑地址映射到物理地址,不同的段映射方法不同,具体的知识请自行查阅.注意:在位置无关代码的执行,到底其程序地址是否和物理地址一致,并没有关系,如果需要寻址某个逻辑地址,一般可用相对PC寻址解决,或者在已经知道物理地址的情况下,根据物理地址和程序地址的关系进行调整,程序计数器(PC)存放的是程序地址*/
stack = start - 0x4000 /* Place PMON stack below PMON start in RAM */
/*定义符号stack 并赋值为start后面16K的地址值,在实际汇编的时候才会展开*/
/* NOTE!! Not more that 16 instructions here!!! Right now it's FULL! 根据mips异常向量表,BEV=1时,reset异常的程序地址为0xbfc00000-0xbfc00200,有0x200个字,可以存储128条指令,但要去除后面ext_map_and_reboot对齐到0x100,占去了64条指令,故这里只能最多有64条指令,何来16条指令?*/
/*协处理器cp0寄存器的定义在sys/arch/mips/include/cpu.h中定义,zero,t0,sp,gp等处理器寄存器的习惯用法定义在sys/arch/mips/include/regdef.h中*/
mtc0 zero, COP_0_STATUS_REG/*将status和cause寄存器清零,复位时status初值为0x30400004,表示发生了复位等错误,运行在内核模式,协处理器0和1可用.清零后,主要是关闭所有中断,清除复位错误,协处理器1不可用,处理器运行在内核模式*/
mtc0 zero, COP_0_CAUSE_REG
li t0, SR_BOOT_EXC_VEC /* Exception to Boostrap Location */
mtc0 t0, COP_0_STATUS_REG /*SR_BOOT_EXC_VEC=0x00400000设置status中的BEV为1,例外向量的入口地址从0xbfc00000开始,也就是从映射到给地址的rom开始*/
la sp, stack /*初始化堆栈指针*/
la gp, _gp /*初始化全局指针,其中_gp是有链接器定义的全局指针变量,sp和gp均需要需要展开,这两条指令会变为4条这样子就有了15条指令*/
bal uncached /* Switch to uncached address space */
nop /*这里需要说明的是,此时程序地址是从0xbfc00000开始的,跳转后,ra=pc+8即bal locate 的加载地址,从反汇编可知,此时pc=0xbfc00000,那么ra=0xbfc00028,与UNCACHED_MEMORY_ADDR或后ra=0xbfc00028,这是从rom加载的时候,若是从其他地址加载,就需要进行地址修正了,此外,副作用是清空流水线和预取指令*/
bal locate /* Get current execute address */
nop
uncached:/*地址修正,*/
or ra, UNCACHED_MEMORY_ADDR/*UNCACHED_MEMORY_ADDR=0xa0000000,参照sys/arch/mips/include/cpu.h,先加载UNCACHED_MEMORY_ADDR,然后or,汇编为2条指令,故共16条指令*/
j ra
nop
/*
* Reboot vector usable from outside pmon.
*//*该段在这里做什么,值得思考.从后面的代码可以看出,此处主要是为了出了异常之后,PMON重新启动的入口地址*/
.align 8
ext_map_and_reboot:
bal CPU_TLBClear
nop
li a0, 0xc0000000
li a1, 0x40000000
bal CPU_TLBInit
nop
la v0, tgt_reboot
la v1, start
subu v0, v1
lui v1, 0xffc0
addu v0, v1
jr v0
nop
/*
* Exception vectors here for rom, before we are up and running. Catch
* whatever comes up before we have a fully fledged exception handler.
*/ /*这里是例外向量,其实啥都没做,就是输出一些相关的信息,然后跳到统一的ex
_common出来处理,这是靠对齐来保证位于位于MIPS体系机构相应的中断向量处,如.align 9 则以2^9为间隔对齐,换成16进制,就是以0x200为间隔*/
.align 9 /* bfc00200 TLB替换(32位) */
la a0, v200_msg
bal stringserial
nop
b exc_common
.align 7 /* bfc00280 TLB替换(64位)*/
la a0, v280_msg
bal stringserial
nop
b exc_common
/* Cache error */
.align 8 /* bfc00300 cache出错*/
PRINTSTR("\r\nPANIC! Unexpected Cache Error exception! ")
mfc0 a0, COP_0_CACHE_ERR
bal hexserial
nop
b exc_common
/* General exception */
.align 7 /* bfc00380 普通中断*/
la a0, v380_msg
bal stringserial
nop
b exc_common
.align 8 /* bfc00400 不可识别的中断*/
la a0, v400_msg
bal stringserial
nop
exc_common:
PRINTSTR("\r\nCAUSE=")
mfc0 a0, COP_0_CAUSE_REG
bal hexserial
nop
PRINTSTR("\r\nSTATUS=")
mfc0 a0, COP_0_STATUS_REG
bal hexserial
nop
PRINTSTR("\r\nERRORPC=")
mfc0 a0, COP_0_ERROR_PC
bal hexserial
nop
PRINTSTR("\r\nEPC=")
mfc0 a0, COP_0_EXC_PC
bal hexserial
nop
PRINTSTR("\r\nDERR0=")
cfc0 a0, COP_0_DERR_0
bal hexserial
nop
PRINTSTR("\r\nDERR1=")
cfc0 a0, COP_0_DERR_1
bal hexserial
nop
// b ext_map_and_reboot /*跳转到reset异常入口 0x100相对地址*/
nop
.align 8
nop
.align 8
.word read
.word write
.word open
.word close
.word nullfunction
.word printf
.word vsprintf
.word nullfunction
.word nullfunction
.word getenv
.word nullfunction
.word nullfunction
.word nullfunction
.word nullfunction
/*
* We get here from executing a bal to get the PC value of the current execute
* location into ra. Check to see if we run from ROM or if this is ramloaded.
*/
locate:/*ramloadded 加载地址为0x81000000*/
la s0,start /*无论是gzram还是gzram,start的均为0x81000000*/
subu s0,ra,s0 /*从rom执行的时候ra=0xbfc00030,若从ram加载,则ra=0x81000030*/
and s0,0xffff0000 /*s0只是测试用的,没有多少实际意义*/
li t0,SR_BOOT_EXC_VEC
mtc0 t0,COP_0_STATUS_REG/*重新设置satus为0x00400000,cause=0x00000000*/
mtc0 zero,COP_0_CAUSE_REG
.set noreorder /*这里似乎多余,前面已经定义了*/
li bonito,PHYS_TO_UNCACHED(BONITO_REG_BASE)
/*下面这一段的宏定义,是针对bonito北桥的一些数据定义*/
/*#define bonito s4 本文件定义
#define PHYS_TO_UNCACHED(x) ((unsigned)(x) | UNCACHED_MEMORY_ADDR) 参照sys/arch/mips/include/cpu.h
#define BONITO_REG_BASE 0x1fe00000 参照Targets/Bonito2fdev/include/bonito.h
反汇编就是 lui $s4,0xbfe0
*/
#define MOD_MASK 0x00000003
#define MOD_B 0x00000000 /* byte "modifier" */
#define MOD_H 0x00000001 /* halfword "modifier" */
#define MOD_W 0x00000002 /* word "modifier" */
#if __mips64
# define MOD_D 0x00000003 /* doubleword "modifier" */
#endif
#define OP_MASK 0x000000fc
#define OP_EXIT 0x00000000 /* exit (status) */
#define OP_DELAY 0x00000008 /* delay (cycles) */
#define OP_RD 0x00000010 /* read (addr) */
#define OP_WR 0x00000014 /* write (addr, val) */
#define OP_RMW 0x00000018 /* read-modify-write (addr, and, or) */
#define OP_WAIT 0x00000020 /* wait (addr, mask, value) */
#define WR_INIT(mod,addr,val) \
.word OP_WR|mod,PHYS_TO_UNCACHED(addr);\
.word (val),0
#define RD_INIT(mod,addr) \
.word OP_RD|mod,PHYS_TO_UNCACHED(addr);\
.word 0,0
#define RMW_INIT(mod,addr,and,or) \
.word OP_RMW|mod,PHYS_TO_UNCACHED(addr);\
.word (and),(or)
#define WAIT_INIT(mod,addr,and,or) \
.word OP_WAIT|mod,PHYS_TO_UNCACHED(addr);\
.word (mask),(val)
#define DELAY_INIT(cycles) \
.word OP_DELAY,(cycles);\
.word 0,0
#define EXIT_INIT(status) \
.word OP_EXIT,(status);\
.word 0,0
#define BONITO_INIT(r,v) WR_INIT(MOD_W,BONITO_BASE+/**/r,v)
#define BONITO_BIS(r,b) RMW_INIT(MOD_W,BONITO_BASE+(r),~0,b)
#define BONITO_BIC(r,b) RMW_INIT(MOD_W,BONITO_BASE+(r),~(b),0)
#define BONITO_RMW(r,c,s) RMW_INIT(MOD_W,BONITO_BASE+(r),~(c),s)
#define CFGADDR(idsel,function,reg) ((1<<(11+(idsel)))+((function)<<8)+(reg))
#define _ISABWR_INIT(mod,function,isabreg,val) \
WR_INIT(MOD_W,BONITO_BASE+BONITO_PCIMAP_CFG,CFGADDR(PCI_IDSEL_VIA686B,function,isabreg)>>16) ; \
RD_INIT(MOD_W,BONITO_BASE+BONITO_PCIMAP_CFG) ; \
WR_INIT(mod,PCI_CFG_SPACE+(CFGADDR(PCI_IDSEL_VIA686B,function,isabreg)&0xffff),val)
#define _ISABRD_INIT(mod,function,isabreg) \
WR_INIT(MOD_W,BONITO_BASE+BONITO_PCIMAP_CFG,CFGADDR(PCI_IDSEL_VIA686B,function,isabreg)>>16) ; \
RD_INIT(MOD_W,BONITO_BASE+BONITO_PCIMAP_CFG) ; \
RD_INIT(mod,PCI_CFG_SPACE+(CFGADDR(PCI_IDSEL_VIA686B,function,isabreg)&0xffff))
#define _ISAWR_INIT(isareg,val) \
WR_INIT(MOD_B,PCI_IO_SPACE+(isareg),val)
#define _ISARD_INIT(isareg) \
RD_INIT(MOD_B,PCI_IO_SPACE+(isareg))
#define ISABBWR_INIT(function,isabreg,val) \
_ISABWR_INIT(MOD_B,function,(isabreg),val)
#define ISABHWR_INIT(function,isabreg,val) \
_ISABWR_INIT(MOD_H,function,(isabreg),val)
#define ISABWWR_INIT(function,isabreg,val) \
_ISABWR_INIT(MOD_W,function,isabreg,val)
#define ISAWR_INIT(isareg,val) \
_ISAWR_INIT(isareg,val)
#define ISARD_INIT(isareg) \
_ISARD_INIT(isareg)
bal 1f
nop
/* bonito endianess */
BONITO_BIC(BONITO_BONPONCFG,BONITO_BONPONCFG_CPUBIGEND)
/*
展开变成
.word 0x00000018|0x00000002,((0x1fe00000+((0x100+0x00)))|0xa0000000);
.word (~(0x00004000)),(0)
*/
BONITO_BIC(BONITO_BONGENCFG,BONITO_BONGENCFG_BYTESWAP|BONITO_BONGENCFG_MSTRBYTESWAP)
BONITO_BIS(BONITO_BONPONCFG, BONITO_BONPONCFG_IS_ARBITER)
/*
* In certain situations it is possible for the Bonito ASIC
* to come up with the PCI registers uninitialised, so do them here
*/
#define PCI_CLASS_BRIDGE 0x06
#define PCI_CLASS_SHIFT 24
#define PCI_SUBCLASS_BRIDGE_HOST 0x00
#define PCI_SUBCLASS_SHIFT 16
#define PCI_COMMAND_IO_ENABLE 0x00000001
#define PCI_COMMAND_MEM_ENABLE 0x00000002
#define PCI_COMMAND_MASTER_ENABLE 0x00000004
#define PCI_COMMAND_STATUS_REG 0x04
#define PCI_MAP_IO 0X00000001
#define PCI_CFG_SPACE BONITO_PCICFG_BASE
BONITO_INIT(BONITO_PCICLASS,(PCI_CLASS_BRIDGE << PCI_CLASS_SHIFT) | (PCI_SUBCLASS_BRIDGE_HOST << PCI_SUBCLASS_SHIFT))
BONITO_INIT(BONITO_PCICMD, BONITO_PCICMD_PERR_CLR|BONITO_PCICMD_SERR_CLR|BONITO_PCICMD_MABORT_CLR|BONITO_PCICMD_MTABORT_CLR|BONITO_PCICMD_TABORT_CLR|BONITO_PCICMD_MPERR_CLR)
//BONITO_INIT(BONITO_PCILTIMER, 0)
BONITO_INIT(BONITO_PCILTIMER, 255)
BONITO_INIT(BONITO_PCIBASE0, 0)
BONITO_INIT(BONITO_PCIBASE1, 0)
BONITO_INIT(BONITO_PCIBASE2, 0)
BONITO_INIT(BONITO_PCIEXPRBASE, 0)
BONITO_INIT(BONITO_PCIINT, 0)
BONITO_BIS(BONITO_PCICMD, BONITO_PCICMD_PERRRESPEN)
BONITO_BIS(BONITO_PCICMD, PCI_COMMAND_IO_ENABLE|PCI_COMMAND_MEM_ENABLE|PCI_COMMAND_MASTER_ENABLE)
BONITO_BIC(BONITO_BONGENCFG, 0x80) #陆没?鹿iobc
#BONITO_BIS(BONITO_BONGENCFG, BONITO_BONGENCFG_BUSERREN)
/* Set debug mode */
BONITO_BIS(BONITO_BONGENCFG, BONITO_BONGENCFG_DEBUGMODE)
/******** added to init southbridge*/
/* Set the SMB base address */
ISABWWR_INIT(4, SMBUS_IO_BASE_ADDR, SMBUS_IO_BASE_VALUE | 0x1)
/* enable the host controller */
ISABHWR_INIT(4, SMBUS_HOST_CONFIG_ADDR, SMBUS_HOST_CONFIG_ENABLE_BIT)
/* enable the SMB IO ports */
ISABBWR_INIT(4, PCI_COMMAND_STATUS_REG, PCI_COMMAND_IO_ENABLE)
/* 15us ISA bus refresh clock */
#define ISAREFRESH (PT_CRYSTAL/(1000000/15))
ISARD_INIT(CTC_PORT+PT_CONTROL)
/* program i8254 ISA refresh counter */
ISAWR_INIT(CTC_PORT+PT_CONTROL,PTCW_SC(PT_REFRESH)|PTCW_16B|PTCW_MODE(MODE_RG))
ISAWR_INIT(CTC_PORT+PT_REFRESH, ISAREFRESH & 0xff)
ISAWR_INIT(CTC_PORT+PT_REFRESH, ISAREFRESH >> 8)
EXIT_INIT(0)
/*展开
.word 0x00000000,(0)
.word 0,0
参数初始化完成
*/
#define Init_Op 0
#define Init_A0 4
#define Init_A1 8
#define Init_A2 12
#define Init_Size 16
/*下面开始初始化北桥*/
1: move a0,ra/*ra此时的值为BONITO_BIC(BONITO_BONPONCFG,BONITO_BONPONCFG_CPUBIGEND)的地址,即初始化数据开始的地址*/
reginit: /* local name */
lw t3, Init_Op(a0)
lw t0, Init_A0(a0)
and t4,t3,OP_MASK
/*
* EXIT(STATUS)
*/
bne t4, OP_EXIT, 8f
nop
move v0,t0
b .done
nop
/*
* DELAY(CYCLES)
*/
8: bne t4, OP_DELAY, 8f
nop
1: bnez t0,1b
subu t0,1
b .next
nop
/*
* READ(ADDR)
*/
8: bne t4,OP_RD,8f
nop
and t4,t3,MOD_MASK
bne t4,MOD_B,1f
nop
lbu t5,0(t0)
b .next
nop
1: bne t4,MOD_H,1f
nop
lhu t5,0(t0)
b .next
nop
1: bne t4,MOD_W,1f
nop
#if __mips64
lwu t5,0(t0)
#else
lw t5,0(t0)
#endif
b .next
nop
1:
#if __mips64
lw t5,0(t0)
b .next
nop
#else
b .fatal
nop
#endif
/*
* WRITE(ADDR,VAL)
*/
8: bne t4,OP_WR,8f
nop
lw t1,Init_A1(a0)
and t4,t3,MOD_MASK
bne t4,MOD_B,1f
nop
sb t1,0(t0)
b .next
nop
1: bne t4,MOD_H,1f
nop
sh t1,0(t0)
b .next
nop
1: bne t4,MOD_W,1f
nop
sw t1,0(t0)
b .next
nop
1:
#if __mips64
sd t1,0(t0)
b .next
nop
#else
b .fatal
nop
#endif
/*
* RMW(ADDR,AND,OR)
*/
8: bne t4,OP_RMW,8f
nop
lw t1,Init_A1(a0)
lw t2,Init_A2(a0)
and t4,t3,MOD_MASK
bne t4,MOD_B,1f
nop
lbu t4,0(t0)
and t4,t1
or t4,t2
sb t4,0(t0)
b .next
nop
1: bne t4,MOD_H,1f
nop
lhu t4,0(t0)
and t4,t1
or t4,t2
sh t4,0(t0)
b .next
nop
1: bne t4,MOD_W,1f
nop
lw t4,0(t0)
and t4,t1
or t4,t2
sw t4,0(t0)
b .next
nop
1:
#if __mips64
ld t4,0(t0)
and t4,t1
or t4,t2
sd t4,0(t0)
b .next
nop
#else
b .fatal
nop
#endif
/*
* WAIT(ADDR,MASK,VAL)
*/
8: bne t4,OP_WAIT,8f
nop
lw t1,Init_A1(a0)
lw t2,Init_A2(a0)
and t4,t3,MOD_MASK
bne t4,MOD_B,1f
nop
3: lbu t4,0(t0)
and t4,t1
bne t4,t2,3b
nop
b .next
nop
1: bne t4,MOD_H,1f
nop
3: lhu t4,0(t0)
and t4,t1
bne t4,t2,3b
nop
b .next
nop
1: bne t4,MOD_W,1f
nop
3: lw t4,0(t0)
and t4,t1
bne t4,t2,3b
nop
b .next
nop
1:
#if __mips64
3: ld t4,0(t0)
and t4,t1
bne t4,t2,3b
nop
b .next
nop
#else
b .fatal
nop
#endif
.next: addu a0,Init_Size
b reginit
nop
8:
.fatal: b .done
nop
bal stuck
nop
.done:
bal superio_init/*初始化南桥的superio*/
nop
bal initserial/*初始化南桥的串口*/
nop
PRINTSTR("\r\nPMON2000 MIPS Initializing. Standby...\r\n")
PRINTSTR("ERRORPC=")
mfc0 a0, COP_0_ERROR_PC
bal hexserial
nop
PRINTSTR(" CONFIG=")
mfc0 a0, COP_0_CONFIG
bal hexserial
nop
PRINTSTR("\r\n")
PRINTSTR(" PRID=")
mfc0 a0, COP_0_PRID
bal hexserial
nop
PRINTSTR("\r\n")
/*
* Now determine DRAM configuration and size by
* reading the I2C EEROM on the DIMMS
*/
#include "i2c.S"/*初始化I2C总线*/
beqz msize,.nodimm
nop
b 2f
nop
.nodimm:
move dbg,a0
PRINTSTR ("\r\nNo DIMM in all slots,use default configure\r\n")
li msize,0x10000000
li sdCfg,0x055043df /* zgj-8-7-14-13 */
2:
PRINTSTR("DIMM SIZE=")
move a0,msize
bal hexserial
nop
PRINTSTR("\r\n")
li t0, 0xbff00008
sd sdCfg, 0(t0)
#### gx 2006-03-17: mode ####
#li t1,0x20
li t1,0x28
li t0, 0xbff00000
sw t1,0(t0)
nop
li t1,0x0
li t0, 0xbff00000
sw t1,0x30(t0)
nop
PRINTSTR("sdcfg=");
move a0,sdCfg
bal hexserial
nop
PRINTSTR("\r\n");
PRINTSTR("msize=");
move a0,msize
bal hexserial
nop
PRINTSTR("\r\n")
skipdimm:
li t1,0 # accumulate pcimembasecfg settings
/* set bar0 mask and translation to point to SDRAM */
sub t0,msize,1
not t0
srl t0,BONITO_PCIMEMBASECFG_ASHIFT-BONITO_PCIMEMBASECFG_MEMBASE0_MASK_SHIFT
and t0,BONITO_PCIMEMBASECFG_MEMBASE0_MASK
or t1,t0
li t0,0x00000000
srl t0,BONITO_PCIMEMBASECFG_ASHIFT-BONITO_PCIMEMBASECFG_MEMBASE0_TRANS_SHIFT
and t0,BONITO_PCIMEMBASECFG_MEMBASE0_TRANS
or t1,t0
or t1,BONITO_PCIMEMBASECFG_MEMBASE0_CACHED
/* set bar1 to minimum size to conserve PCI space */
li t0, ~0
srl t0,BONITO_PCIMEMBASECFG_ASHIFT-BONITO_PCIMEMBASECFG_MEMBASE1_MASK_SHIFT
and t0,BONITO_PCIMEMBASECFG_MEMBASE1_MASK
or t1,t0
li t0,0x00000000
srl t0,BONITO_PCIMEMBASECFG_ASHIFT-BONITO_PCIMEMBASECFG_MEMBASE1_TRANS_SHIFT
and t0,BONITO_PCIMEMBASECFG_MEMBASE1_TRANS
or t1,t0
or t1,BONITO_PCIMEMBASECFG_MEMBASE1_CACHED
sw t1,BONITO_PCIMEMBASECFG(bonito)
/* enable configuration cycles now */
lw t0,BONITO_BONPONCFG(bonito)
and t0,~BONITO_BONPONCFG_CONFIG_DIS
sw t0,BONITO_BONPONCFG(bonito)
PRINTSTR("Init SDRAM Done!\r\n");
/*
* Reset and initialize caches to a known state.
*/
#define IndexStoreTagI 0x08
#define IndexStoreTagD 0x09
#define IndexStoreTagS 0x0b
#define IndexStoreTagT 0x0a
#define FillI 0x14
/*
* RM7000 config register bits.
*/
#define CF_7_SE (1 << 3) /* Secondary cache enable */
#define CF_7_SC (1 << 31) /* Secondary cache not present */
#define CF_7_TE (1 << 12) /* Tertiary cache enable */
#define CF_7_TC (1 << 17) /* Tertiary cache not present */
#define CF_7_TS (3 << 20) /* Tertiary cache size */
#define CF_7_TS_AL 20 /* Shift to align */
#define NOP8 nop;nop;nop;nop;nop;nop;nop;nop
do_caches:
TTYDBG("Sizing caches...\r\n");
mfc0 t3, COP_0_CONFIG /* t3 = original config */
and t3, 0xffffeff0 /* Make sure coherency is OK */
and t3, ~(CF_7_TE|CF_7_SE|CF_7_TC|CF_7_SC) /* disable L2/L3 cache */
mtc0 t3, COP_0_CONFIG
li t2, 4096
srl t1, t3, 9
and t1, 3
sllv s3, t2, t1 /* s3 = I cache size */
#ifdef CONFIG_CACHE_64K_4WAY
sll s3,2
#endif
and t1, t3, 0x20
srl t1, t1, 1
addu s4, t1, 16 /* s4 = I cache line size */
srl t1, t3, 6
and t1, 3
sllv s5, t2, t1 /* s5 = D cache size */
#ifdef CONFIG_CACHE_64K_4WAY
sll s5,2
#endif
and t1, t3, 0x10
addu s6, t1, 16 /* s6 = D cache line size */
TTYDBG("Init caches...\r\n")
li s7, 0 /* no L2 cache */
li s8, 0 /* no L3 cache */
#if 0
mfc0 a0, COP_0_PRID
li a1, 0x6301
bne a0,a1,1f
nop
#endif
TTYDBG("godson2 caches found\r\n")
bal godson2_cache_init
nop
/* close L2 cache */
li a0, 0xbfe00164
sw zero, 0(a0);
mfc0 a0,COP_0_CONFIG
and a0,a0,~((1<<12) | 3)
or a0,a0,2
mtc0 a0,COP_0_CONFIG
#ifdef DEBUG_LOCORE
TTYDBG("Init caches done, cfg = ")
mfc0 a0, COP_0_CONFIG
bal hexserial
nop
TTYDBG("\r\n\r\n")
#endif
/* zhb */
#if 0
/* li t0, 0 */
/* li t1, 0x90000 */
/*1: addiu t0, 1 */
/* bne t0, t1, 1b */
nop
TTYDBG("Testing memory...\r\n")
li t7, 10
tmem:
li t0, 0xa0000000+1*1024*1024
li t1, 0xa0000000
li t2, 0xffffffff
1:
sw t2, 0(t1)
lw t3, 0(t1)
bne t3, t2, 1f
nop
not t2
sw t2, 0(t1)
lw t3, 0(t1)
bne t3, t2, 1f
nop
not t2
subu t2, 1
addu t1, 4
beq t1, t0, 2f
nop
and t4, t1, 0x000fffff
bnez t4, skipdot
li a0, '.'
bal tgt_putchar
nop
skipdot:
b 1b
nop
1:
TTYDBG("Memory test failed at ");
move a0, t1
bal hexserial
nop
TTYDBG("\r\nWrite=");
move a0, t2
bal hexserial
nop
TTYDBG("\r\nRead=");
move a0, t3
bal hexserial
nop
1:
b 1b
nop
2:
TTYDBG("Testing ok...\r\n");
sub t7,1
beqz t7, 1f
nop
b tmem
nop
1:
b 1b
nop
#endif
#include "machine/newtest/mydebug.S"
bootnow:
TTYDBG("Copy PMON to execute location...\r\n")
#ifdef DEBUG_LOCORE
TTYDBG(" start = 0x")
la a0, start
bal hexserial
nop
TTYDBG("\r\n s0 = 0x")
move a0, s0
bal hexserial
nop
TTYDBG("\r\n")
#endif
la a0, start
li a1, 0xbfc00000
la a2, _edata
or a0, 0xa0000000
or a2, 0xa0000000
subu t1, a2, a0
srl t1, t1, 2
move t0, a0
move t1, a1
move t2, a2
/* copy text section */
1: and t3,t0,0x0000ffff
bnez t3,2f
nop
move a0,t0
bal hexserial
nop
li a0,'\r'
bal tgt_putchar
nop
2: lw t3, 0(t1)
nop
sw t3, 0(t0)
addu t0, 4
addu t1, 4
bne t2, t0, 1b
nop
PRINTSTR("\ncopy text section done.\r\n")
/* Clear BSS */
la a0, _edata
la a2, _end
2: sw zero, 0(a0)
bne a2, a0, 2b
addu a0, 4
TTYDBG("Copy PMON to execute location done.\r\n")
/* zhb */
#if 0
zhb:
TTYDBG("Testing...\r\n")
la a0, start
li a1, 0xbfc00000
la a2, _edata
or a0, 0xa0000000
or a2, 0xa0000000
/* subu s6, a2, a0*/
/* srl s6, s6, 2*/
move t0, a0
move t1, a1
move t2, a2
/* copy text section */
1: lw t4, 0(t1)
nop
lw t5, 0(t0)
addu t0, 4
addu t1, 4
beq t4, t5, 2f
nop
move a0, t0
subu a0, 4
bal hexserial
nop
TTYDBG (" ")
move a0, t4
bal hexserial
nop
TTYDBG (" ")
move a0, t5
bal hexserial
nop
TTYDBG ("\r\n")
2: bne t2, t0, 1b
nop
TTYDBG ("test ok!\r\n")
/*
3: beqz zero, 3b
nop
*/
#endif
TTYDBG("sp=");
move a0, sp
bal hexserial
nop
li a0, 4096*1024
sw a0, CpuTertiaryCacheSize /* Set L3 cache size */
#if 0
mfc0 a0,COP_0_CONFIG
and a0,a0,0xfffffff8
or a0,a0,0x3
mtc0 a0,COP_0_CONFIG
#endif
move a0,msize
srl a0,20
/* pass pointer to kseg1 tgt_putchar */
la a1, tgt_putchar
addu a1,a1,s0
la a2, stringserial
addu a2,a2,s0
la v0, initmips
jalr v0
nop
stuck:
#ifdef DEBUG_LOCORE
TTYDBG("Dumping GT64240 setup.\r\n")
TTYDBG("offset----data------------------------.\r\n")
li s3, 0
1:
move a0, s3
bal hexserial
nop
TTYDBG(": ")
2:
add a0, s3, bonito
lw a0, 0(a0)
bal hexserial
addiu s3, 4
TTYDBG(" ")
li a0, 0xfff
and a0, s3
beqz a0, 3f
li a0, 0x01f
and a0, s3
bnez a0, 2b
TTYDBG("\r\n")
b 1b
nop
3:
b 3b
nop
#else
b stuck
nop
#endif
/*
* Clear the TLB. Normally called from start.S.
*/
#if __mips64
#define MTC0 dmtc0
#else
#define MTC0 mtc0
#endif
LEAF(CPU_TLBClear)
li a3, 0 # First TLB index.
li a2, PG_SIZE_4K
MTC0 a2, COP_0_TLB_PG_MASK # Whatever...
1:
MTC0 zero, COP_0_TLB_HI # Clear entry high.
MTC0 zero, COP_0_TLB_LO0 # Clear entry low0.
MTC0 zero, COP_0_TLB_LO1 # Clear entry low1.
mtc0 a3, COP_0_TLB_INDEX # Set the index.
addiu a3, 1
li a2, 64
nop
nop
tlbwi # Write the TLB
bne a3, a2, 1b
nop
jr ra
nop
END(CPU_TLBClear)
/*
* Set up the TLB. Normally called from start.S.
*/
LEAF(CPU_TLBInit)
li a3, 0 # First TLB index.
li a2, PG_SIZE_16M
MTC0 a2, COP_0_TLB_PG_MASK # All pages are 16Mb.
1:
and a2, a0, PG_SVPN
MTC0 a2, COP_0_TLB_HI # Set up entry high.
move a2, a0
srl a2, a0, PG_SHIFT
and a2, a2, PG_FRAME
ori a2, PG_IOPAGE
MTC0 a2, COP_0_TLB_LO0 # Set up entry low0.
addu a2, (0x01000000 >> PG_SHIFT)
MTC0 a2, COP_0_TLB_LO1 # Set up entry low1.
mtc0 a3, COP_0_TLB_INDEX # Set the index.
addiu a3, 1
li a2, 0x02000000
subu a1, a2
nop
tlbwi # Write the TLB
bgtz a1, 1b
addu a0, a2 # Step address 32Mb.
jr ra
nop
END(CPU_TLBInit)
LEAF(stringserial)
move a2, ra
addu a1, a0, s0
lbu a0, 0(a1)
1:
beqz a0, 2f
nop
bal tgt_putchar
addiu a1, 1
b 1b
lbu a0, 0(a1)
2:
j a2
nop
END(stringserial)
LEAF(outstring)
move a2, ra
move a1, a0
lbu a0, 0(a1)
1:
beqz a0, 2f
nop
bal tgt_putchar
addiu a1, 1
b 1b
lbu a0, 0(a1)
2:
j a2
nop
END(outstring)
LEAF(hexserial)
move a2, ra
move a1, a0
li a3, 7
1:
rol a0, a1, 4
move a1, a0
and a0, 0xf
la v0, hexchar
addu v0, s0
addu v0, a0
bal tgt_putchar
lbu a0, 0(v0)
bnez a3, 1b
addu a3, -1
j a2
nop
END(hexserial)
LEAF(tgt_putchar)
la v0, COM1_BASE_ADDR
1:
lbu v1, NSREG(NS16550_LSR)(v0)
and v1, LSR_TXRDY
beqz v1, 1b
nop
sb a0, NSREG(NS16550_DATA)(v0)
#ifdef HAVE_NB_SERIAL
move v1,v0
la v0, COM3_BASE_ADDR
bne v0,v1,1b
nop
#endif
j ra
nop
END(tgt_putchar)
/* baud rate definitions, matching include/termios.h */
#define B0 0
#define B50 50
#define B75 75
#define B110 110
#define B134 134
#define B150 150
#define B200 200
#define B300 300
#define B600 600
#define B1200 1200
#define B1800 1800
#define B2400 2400
#define B4800 4800
#define B9600 9600
#define B19200 19200
#define B38400 38400
#define B57600 57600
#define B115200 115200
LEAF(initserial)
la v0, COM1_BASE_ADDR
la a0, NS16550HZ/2/(16*CONS_BAUD)
1:
li v1, FIFO_ENABLE|FIFO_RCV_RST|FIFO_XMT_RST|FIFO_TRIGGER_4
sb v1, NSREG(NS16550_FIFO)(v0)
li v1, CFCR_DLAB
sb v1, NSREG(NS16550_CFCR)(v0)
sb a0, NSREG(NS16550_DATA)(v0)
srl v1, 8
sb v1, NSREG(NS16550_IER)(v0)
li v1, CFCR_8BITS
sb v1, NSREG(NS16550_CFCR)(v0)
li v1, MCR_DTR|MCR_RTS
sb v1, NSREG(NS16550_MCR)(v0)
li v1, 0x0
sb v1, NSREG(NS16550_IER)(v0)
#ifdef HAVE_NB_SERIAL
move v1,v0
la v0, COM3_BASE_ADDR
li a0, NS16550HZ/(16*CONS_BAUD)
bne v0,v1,1b
nop
#endif
j ra
nop
END(initserial)
/* a0: slave address
a1: reg off
*/
LEAF(i2cread)
/* set device address */
li v0, 0xbfd00000 + SMBUS_HOST_ADDRESS
sb a0, 0(v0);
/* store register offset */
li v0, 0xbfd00000 + SMBUS_HOST_COMMAND
sb a1, 0(v0);
/* read byte data protocol */
li v0, 0x08
li v1, 0xbfd00000 + SMBUS_HOST_CONTROL
sb v0, 0(v1);
/* make sure SMB host ready to start, important!--zfx */
li v1, 0xbfd00000 + SMBUS_HOST_STATUS
lbu v0, 0(v1)
andi v0,v0, 0x1f
beqz v0,1f
nop
sb v0, 0(v1)
lbu v0, 0(v1) #flush the write
1:
/* start */
li v1, 0xbfd00000 + SMBUS_HOST_CONTROL
lbu v0, 0(v1)
ori v0, v0, 0x40
sb v0, 0(v1);
/* wait */
li v1, 0xbfd00000 + SMBUS_HOST_STATUS
1:
#if 0
/* delay */
li a0, 0x1000
2:
bnez a0,2b
addiu a0, -1
#endif
lbu v0, 0(v1)
andi v0, SMBUS_HOST_STATUS_BUSY
bnez v0, 1b #IDEL ?
nop
li v1, 0xbfd00000 + SMBUS_HOST_STATUS
lbu v0, 0(v1)
andi v0,v0, 0x1f
beqz v0,1f
nop
sb v0, 0(v1) #reset
lbu v0, 0(v1) #flush the write
1:
li v1, 0xbfd00000 + SMBUS_HOST_DATA0
lbu v0, 0(v1)
jr ra
nop
END(i2cread)
__main:
j ra
nop
.rdata
transmit_pat_msg:
.asciz "\r\nInvalid transmit pattern. Must be DDDD or DDxDDx\r\n"
v200_msg:
.asciz "\r\nPANIC! Unexpected TLB refill exception!\r\n"
v280_msg:
.asciz "\r\nPANIC! Unexpected XTLB refill exception!\r\n"
v380_msg:
.asciz "\r\nPANIC! Unexpected General exception!\r\n"
v400_msg:
.asciz "\r\nPANIC! Unexpected Interrupt exception!\r\n"
hexchar:
.ascii "0123456789abcdef"
.text
.align 2
/*
* I2C Functions used in early startup code to get SPD info from
* SDRAM modules. This code must be entirely PIC and RAM independent.
*/
/* Delay macro */
#define DELAY(count) \
li v0, count; \
99: \
bnz vo, 99b;\
addiu v0, -1
#define I2C_INT_ENABLE 0x80
#define I2C_ENABLE 0x40
#define I2C_ACK 0x04
#define I2C_INT_FLAG 0x08
#define I2C_STOP_BIT 0x10
#define I2C_START_BIT 0x20
#define I2C_AMOD_RD 0x01
#define BUS_ERROR 0x00
#define START_CONDITION_TRA 0x08
#define RSTART_CONDITION_TRA 0x10
#define ADDR_AND_WRITE_BIT_TRA_ACK_REC 0x18
#define ADDR_AND_READ_BIT_TRA_ACK_REC 0x40
#define SLAVE_REC_WRITE_DATA_ACK_TRA 0x28
#define MAS_REC_READ_DATA_ACK_NOT_TRA 0x58
#define Index_Store_Tag_D 0x05
#define Index_Invalidate_I 0x00
#define Index_Writeback_Inv_D 0x01
#define Index_Store_Tag_S 0x0b
#define Index_Writeback_Inv_S 0x03
LEAF(nullfunction)
jr ra
nop
END(nullfunction)
LEAF(godson2_cache_init)
####part 2####
cache_detect_2way:
mfc0 t4, CP0_CONFIG
andi t5, t4, 0x0e00
srl t5, t5, 9
andi t6, t4, 0x01c0
srl t6, t6, 6
addiu t6, t6, 11
addiu t5, t5, 11
addiu t4, $0, 1
sllv t6, t4, t6
srl t6,1
sllv t5, t4, t5
srl t5,1
addiu t7, $0, 2
####part 3####
lui a0, 0x8000
addu a1, $0, t5
addu a2, $0, t6
cache_init_d2way:
#a0=0x80000000, a1=icache_size, a2=dcache_size
#a3, v0 and v1 used as local registers
mtc0 $0, CP0_TAGHI
addu v0, $0, a0
addu v1, a0, a2
1: slt a3, v0, v1
beq a3, $0, 1f
nop
mtc0 $0, CP0_TAGLO
cache Index_Store_Tag_D, 0x0(v0)
mtc0 $0, CP0_TAGLO
cache Index_Store_Tag_D, 0x1(v0)
mtc0 $0, CP0_TAGLO
cache Index_Store_Tag_D, 0x2(v0)
mtc0 $0, CP0_TAGLO
cache Index_Store_Tag_D, 0x3(v0)
beq $0, $0, 1b
addiu v0, v0, 0x20
#if 1
1:
cache_init_l24way:
mtc0 $0, CP0_TAGHI
addu v0, $0, a0
addu v1, a0, 128*1024
1: slt a3, v0, v1
beq a3, $0, 1f
nop
mtc0 $0, CP0_TAGLO
cache Index_Store_Tag_S, 0x0(v0)
mtc0 $0, CP0_TAGLO
cache Index_Store_Tag_S, 0x1(v0)
mtc0 $0, CP0_TAGLO
cache Index_Store_Tag_S, 0x2(v0)
mtc0 $0, CP0_TAGLO
cache Index_Store_Tag_S, 0x3(v0)
beq $0, $0, 1b
addiu v0, v0, 0x20
1:
cache_flush_4way:
addu v0, $0, a0
addu v1, a0, 128*1024
1: slt a3, v0, v1
beq a3, $0, 1f
nop
cache Index_Writeback_Inv_S, 0x0(v0)
cache Index_Writeback_Inv_S, 0x1(v0)
cache Index_Writeback_Inv_S, 0x2(v0)
cache Index_Writeback_Inv_S, 0x3(v0)
beq $0, $0, 1b
addiu v0, v0, 0x20
# endif
1:
cache_flush_i2way:
addu v0, $0, a0
addu v1, a0, a1
1: slt a3, v0, v1
beq a3, $0, 1f
nop
cache Index_Invalidate_I, 0x0(v0)
# cache Index_Invalidate_I, 0x1(v0)
# cache Index_Invalidate_I, 0x2(v0)
# cache Index_Invalidate_I, 0x3(v0)
beq $0, $0, 1b
addiu v0, v0, 0x20
1:
cache_flush_d2way:
addu v0, $0, a0
addu v1, a0, a2
1: slt a3, v0, v1
beq a3, $0, 1f
nop
cache Index_Writeback_Inv_D, 0x0(v0)
cache Index_Writeback_Inv_D, 0x1(v0)
cache Index_Writeback_Inv_D, 0x2(v0)
cache Index_Writeback_Inv_D, 0x3(v0)
beq $0, $0, 1b
addiu v0, v0, 0x20
1:
cache_init_finish:
nop
jr ra
nop
cache_init_panic:
TTYDBG("cache init panic\r\n");
1: b 1b
nop
.end godson2_cache_init
#define PCICONF_WRITEB(dev,func,reg,data) \
li a0,CFGADDR(dev,func,reg); \
li a1,PHYS_TO_UNCACHED(PCI_CFG_SPACE); \
and a2,a0,0xffff; \
or a1,a2; \
srl a0,16; \
li a2,BONITO_BASE+BONITO_PCIMAP_CFG; \
sw a0,BONITO_PCIMAP_CFG(bonito); \
lw zero,BONITO_PCIMAP_CFG(bonito); \
or a0,zero,data; \
sb a0,(a1);
#define PCICONF_WRITEW(dev,func,reg,data) \
li a0,CFGADDR(dev,func,reg); \
li a1,PHYS_TO_UNCACHED(PCI_CFG_SPACE); \
and a2,a0,0xffff; \
or a1,a2; \
srl a0,16; \
li a2,BONITO_BASE+BONITO_PCIMAP_CFG; \
sw a0,BONITO_PCIMAP_CFG(bonito); \
lw zero,BONITO_PCIMAP_CFG(bonito); \
or a0,zero,data; \
sw a0,(a1);
#define PCICONF_ORB(dev,func,reg,data) \
li a0,CFGADDR(dev,func,reg); \
li a1,PHYS_TO_UNCACHED(PCI_CFG_SPACE); \
and a2,a0,0xffff; \
or a1,a2; \
srl a0,16; \
li a2,BONITO_BASE+BONITO_PCIMAP_CFG; \
sw a0,BONITO_PCIMAP_CFG(bonito); \
lw zero,BONITO_PCIMAP_CFG(bonito); \
lbu a2,(a1); \
ori a2,data; \
sw a0,BONITO_PCIMAP_CFG(bonito); \
lw zero,BONITO_PCIMAP_CFG(bonito); \
sb a2,(a1);
#define SUPERIO_WR(idx,data) \
li v0,BONITO_PCIIO_BASE_VA+0x3f0; \
or v1,zero,idx; \
sb v1,(v0); \
or v1,zero,data; \
sb v1,1(v0);
#define E2_EPP 2
#define E2_S1 (1<<2)
#define E2_S2 (1<<3)
#define E2_FLOPPY (1<<4)
LEAF(superio_init)
PCICONF_WRITEW(PCI_IDSEL_VIA686B,0,4,7);
/*positive decode*/
PCICONF_ORB(PCI_IDSEL_VIA686B,0,0x81,0x80);
PCICONF_WRITEB(PCI_IDSEL_VIA686B,0,0x83,0x80|0x1| 0x8);
PCICONF_WRITEB(PCI_IDSEL_VIA686B,0,0x85,3);
/* enable RTC/PS2/KBC */
PCICONF_WRITEB(PCI_IDSEL_VIA686B,0,0x5A,7);
SUPERIO_WR(0xe2,E2_S2|E2_S1|E2_EPP|E2_FLOPPY) /*enable serial and floppy */
SUPERIO_WR(0xe3,0x3f0>>2) /*floppy base address*/
SUPERIO_WR(0xe6,0x378>>2) /*parallel port*/
SUPERIO_WR(0xe7,0x3f8>>2) /*set serial port1 base addr 0x3f8*/
SUPERIO_WR(0xe8,0x2f8>>2) /*set serial port2 base addr 0x2f8*/
SUPERIO_WR(0xee,0xc0) /* both ports on high speed*/
PCICONF_WRITEB(PCI_IDSEL_VIA686B,0,0x85,1)
jr ra
nop
END(superio_init)
 |
|
老杳，中国科技大学博士，曾就职于联想集团、普天集团及信息产业部从事IPTV、智能手机及集成电路等业务。
-->
ADI论坛：答疑解惑，申请样品
训练有素的ADI技术团队坐镇解答网友提问，免费申请ADI样片和工程师手册，数量有限！
参与ADI隔离产品活动，赢取ADUM开发板和隔离产品样片
ADI实验室电路（CFTL）有奖转发活动
分享ADI新产品，抢先体验最新放大器样片
专家坐堂---把脉心电图(ECG)解决方案
安森美LED驱动器和高能效设计中心
学习安森美LED与能效设计相关诀窍、技巧及技术，下载资料、视频和研讨会学习，每月赢取惊喜礼品。
消费电子设计技巧
汇集消费电子设计方面的各种窍门和思路，提供了多种参考方案和技术要点及PLD消费应用。
- 菜农Cortex-M0技术交流 12047788
- EDN-哈尔滨 75642591
- EDN-上海 15156661
- EDN-广州 57660943
- EDN-桂林 48813559
- EDN-武汉 25150805
- EDN-模拟电路 2837145
- EDN-USB 16070601
- EDN-通讯 30548292
- EDN-综合 57490949
促进EDN网友交流合作，方便EDN网友学习沟通
扫一扫
5395
被折叠的 条评论
为什么被折叠?
到【灌水乐园】发言
