mini2440 I2C驱动的分析与学习(二)

接着分析i2c的数据传输流程。

首先是打开i2c设备，比如open("/dev/i2c/0")，在内核调用下面函数

static int i2cdev_open(struct inode *inode, struct file *file)
{
	unsigned int minor = iminor(inode);
	struct i2c_client *client;
	struct i2c_adapter *adap;
	struct i2c_dev *i2c_dev;
	int ret = 0;

	lock_kernel();
	i2c_dev = i2c_dev_get_by_minor(minor);
	if (!i2c_dev) {
		ret = -ENODEV;
		goto out;
	}

	adap = i2c_get_adapter(i2c_dev->adap->nr);
	if (!adap) {
		ret = -ENODEV;
		goto out;
	}

	/* This creates an anonymous i2c_client, which may later be
	 * pointed to some address using I2C_SLAVE or I2C_SLAVE_FORCE.
	 *
	 * This client is ** NEVER REGISTERED ** with the driver model
	 * or I2C core code!!  It just holds private copies of addressing
	 * information and maybe a PEC flag.
	 */
	client = kzalloc(sizeof(*client), GFP_KERNEL);
	if (!client) {
		i2c_put_adapter(adap);
		ret = -ENOMEM;
		goto out;
	}
	snprintf(client->name, I2C_NAME_SIZE, "i2c-dev %d", adap->nr);
	client->driver = &i2cdev_driver;

	client->adapter = adap;
	file->private_data = client;

out:
	unlock_kernel();
	return ret;
}

这里就是根据设备的minor号，生成了i2c_client结构体。以后在操作文件的时候，就可以把对i2c_client进行操作了。在i2c_client中有device, 也有device_driver。因此，i2c_client是更高层次的抽象。

 

先看设备的写函数：

static ssize_t i2cdev_write (struct file *file, const char __user *buf, size_t count,
                             loff_t *offset)
{
	int ret;
	char *tmp;
	struct i2c_client *client = (struct i2c_client *)file->private_data;

	if (count > 8192)
		count = 8192;

	tmp = kmalloc(count,GFP_KERNEL);
	if (tmp==NULL)
		return -ENOMEM;
	if (copy_from_user(tmp,buf,count)) {
		kfree(tmp);
		return -EFAULT;
	}

	pr_debug("i2c-dev: i2c-%d writing %zu bytes.\n",
		iminor(file->f_path.dentry->d_inode), count);

	ret = i2c_master_send(client,tmp,count);
	kfree(tmp);
	return ret;
}

在这里调用i2c_master_send函数。

 

int i2c_master_send(struct i2c_client *client,const char *buf ,int count)
{
	int ret;
	struct i2c_adapter *adap=client->adapter;
	struct i2c_msg msg;

	msg.addr = client->addr;
	msg.flags = client->flags & I2C_M_TEN;
	msg.len = count;
	msg.buf = (char *)buf;

	ret = i2c_transfer(adap, &msg, 1);

	/* If everything went ok (i.e. 1 msg transmitted), return #bytes
	   transmitted, else error code. */
	return (ret == 1) ? count : ret;
}

这样又调用了i2c_transfer函数。不论读写，最后都是通过这个函数进行操作的。

int i2c_transfer(struct i2c_adapter *adap, struct i2c_msg *msgs, int num)
{
	unsigned long orig_jiffies;
	int ret, try;
	if (adap->algo->master_xfer) {
		if (in_atomic() || irqs_disabled()) {
			ret = mutex_trylock(&adap->bus_lock);
			if (!ret)
				/* I2C activity is ongoing. */
				return -EAGAIN;
		} else {
			mutex_lock_nested(&adap->bus_lock, adap->level);
		}

		/* Retry automatically on arbitration loss */
		orig_jiffies = jiffies;
		for (ret = 0, try = 0; try <= adap->retries; try++) {
			ret = adap->algo->master_xfer(adap, msgs, num);
			if (ret != -EAGAIN)
				break;
			if (time_after(jiffies, orig_jiffies + adap->timeout))
				break;
		}
		mutex_unlock(&adap->bus_lock);

		return ret;
	} else {
		dev_dbg(&adap->dev, "I2C level transfers not supported\n");
		return -EOPNOTSUPP;
	}
}

利用adap->algo->master_xfer进行传输。这个函数是在我们自己的文件中实现的。

最终调用了s3c24xx_i2c_doxfer函数。在这个函数中，只是传输i2c协议中的第一个byte。每传输完一个byte之后，会产生一个中断，其余的数据都是在中断函数中进行传输的。具体的关于i2c的内容，可以在arm的芯片手册和eeprom的芯片手册中看到。

static int i2s_s3c_irq_nextbyte(struct s3c24xx_i2c *i2c, unsigned long iicstat)
{
	unsigned long tmp;
	unsigned char byte;
	int ret = 0;

	switch (i2c->state) {

	case STATE_IDLE:
		dev_err(i2c->dev, "%s: called in STATE_IDLE\n", __func__);
		goto out;
		break;

	case STATE_STOP:
		dev_err(i2c->dev, "%s: called in STATE_STOP\n", __func__);
		s3c24xx_i2c_disable_irq(i2c);
		goto out_ack;

	case STATE_START:
		/* last thing we did was send a start condition on the
		 * bus, or started a new i2c message
		 */

		if (iicstat & S3C2410_IICSTAT_LASTBIT &&
		    !(i2c->msg->flags & I2C_M_IGNORE_NAK)) {
			/* ack was not received... */

			dev_dbg(i2c->dev, "ack was not received\n");
			s3c24xx_i2c_stop(i2c, -ENXIO);
			goto out_ack;
		}

		if (i2c->msg->flags & I2C_M_RD)
			i2c->state = STATE_READ;
		else
			i2c->state = STATE_WRITE;

		/* terminate the transfer if there is nothing to do
		 * as this is used by the i2c probe to find devices. */

		if (is_lastmsg(i2c) && i2c->msg->len == 0) {
			s3c24xx_i2c_stop(i2c, 0);
			goto out_ack;
		}

		if (i2c->state == STATE_READ)
			goto prepare_read;

		/* fall through to the write state, as we will need to
		 * send a byte as well */

	case STATE_WRITE:
		/* we are writing data to the device... check for the
		 * end of the message, and if so, work out what to do
		 */

		if (!(i2c->msg->flags & I2C_M_IGNORE_NAK)) {
			if (iicstat & S3C2410_IICSTAT_LASTBIT) {
				dev_dbg(i2c->dev, "WRITE: No Ack\n");

				s3c24xx_i2c_stop(i2c, -ECONNREFUSED);
				goto out_ack;
			}
		}

 retry_write:

		if (!is_msgend(i2c)) {
			byte = i2c->msg->buf[i2c->msg_ptr++];
			printk( "%02x ", byte);
			
			writeb(byte, i2c->regs + S3C2410_IICDS);

			/* delay after writing the byte to allow the
			 * data setup time on the bus, as writing the
			 * data to the register causes the first bit
			 * to appear on SDA, and SCL will change as
			 * soon as the interrupt is acknowledged */

			ndelay(i2c->tx_setup);

		} else if (!is_lastmsg(i2c)) {
			/* we need to go to the next i2c message */

			dev_dbg(i2c->dev, "WRITE: Next Message\n");

			i2c->msg_ptr = 0;
			i2c->msg_idx++;
			i2c->msg++;

			/* check to see if we need to do another message */
			if (i2c->msg->flags & I2C_M_NOSTART) {

				if (i2c->msg->flags & I2C_M_RD) {
					/* cannot do this, the controller
					 * forces us to send a new START
					 * when we change direction */

					s3c24xx_i2c_stop(i2c, -EINVAL);
				}

				goto retry_write;
			} else {
				/* send the new start */
				s3c24xx_i2c_message_start(i2c, i2c->msg);
				i2c->state = STATE_START;
			}

		} else {
			/* send stop */

			s3c24xx_i2c_stop(i2c, 0);
		}
		break;

	case STATE_READ:
		/* we have a byte of data in the data register, do
		 * something with it, and then work out wether we are
		 * going to do any more read/write
		 */

		byte = readb(i2c->regs + S3C2410_IICDS);
		printk( "%02x ", byte);
		i2c->msg->buf[i2c->msg_ptr++] = byte;

 prepare_read:
		if (is_msglast(i2c)) {
			/* last byte of buffer */

			if (is_lastmsg(i2c))
				s3c24xx_i2c_disable_ack(i2c);   
		/* NO ACK  means the ernd of read. Is it possible here wusq */

		} else if (is_msgend(i2c)) {
			/* ok, we've read the entire buffer, see if there
			 * is anything else we need to do */

			if (is_lastmsg(i2c)) {
				/* last message, send stop and complete */
				dev_dbg(i2c->dev, "READ: Send Stop\n");

				s3c24xx_i2c_stop(i2c, 0);
			} else {
				/* go to the next transfer */
				dev_dbg(i2c->dev, "READ: Next Transfer\n");

				i2c->msg_ptr = 0;
				i2c->msg_idx++;
				i2c->msg++;
			}
		}

		break;
	}

	/* acknowlegde the IRQ and get back on with the work */

 out_ack:
	tmp = readl(i2c->regs + S3C2410_IICCON);
	tmp &= ~S3C2410_IICCON_IRQPEND;
	writel(tmp, i2c->regs + S3C2410_IICCON);
 out:
	return ret;
}

/* s3c24xx_i2c_irq
 *
 * top level IRQ servicing routine
*/

static irqreturn_t s3c24xx_i2c_irq(int irqno, void *dev_id)
{
	struct s3c24xx_i2c *i2c = dev_id;
	unsigned long status;
	unsigned long tmp;

	status = readl(i2c->regs + S3C2410_IICSTAT);

	if (status & S3C2410_IICSTAT_ARBITR) {
		/* deal with arbitration loss */
		dev_err(i2c->dev, "deal with arbitration loss\n");
	}

	if (i2c->state == STATE_IDLE) {
		dev_dbg(i2c->dev, "IRQ: error i2c->state == IDLE\n");

		tmp = readl(i2c->regs + S3C2410_IICCON);
		tmp &= ~S3C2410_IICCON_IRQPEND;
		writel(tmp, i2c->regs +  S3C2410_IICCON);
		goto out;
	}

	/* pretty much this leaves us with the fact that we've
	 * transmitted or received whatever byte we last sent */

	i2s_s3c_irq_nextbyte(i2c, status);

 out:
	return IRQ_HANDLED;
}