z-stac配置按键

按键的定义一般有两种，开关和摇杆。这里只讨论开关的定义。

根据硬件在hal_board_cfg.h中定义

在hal_key.h中定义宏位

在hal_key.c中需要初始化相关寄存器

附录：

hal_board_cfg.h

/**************************************************************************************************
  Filename:       hal_board_cfg.h
  Revised:        $Date: 2009-08-24 10:47:59 -0700 (Mon, 24 Aug 2009) $
  Revision:       $Revision: 20635 $

  Description:    Describe the purpose and contents of the file.


  Copyright 2006-2009 Texas Instruments Incorporated. All rights reserved.

  IMPORTANT: Your use of this Software is limited to those specific rights
  granted under the terms of a software license agreement between the user
  who downloaded the software, his/her employer (which must be your employer)
  and Texas Instruments Incorporated (the "License").  You may not use this
  Software unless you agree to abide by the terms of the License. The License
  limits your use, and you acknowledge, that the Software may not be modified,
  copied or distributed unless embedded on a Texas Instruments microcontroller
  or used solely and exclusively in conjunction with a Texas Instruments radio
  frequency transceiver, which is integrated into your product.  Other than for
  the foregoing purpose, you may not use, reproduce, copy, prepare derivative
  works of, modify, distribute, perform, display or sell this Software and/or
  its documentation for any purpose.

  YOU FURTHER ACKNOWLEDGE AND AGREE THAT THE SOFTWARE AND DOCUMENTATION ARE
  PROVIDED 揂S IS?WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED,
  INCLUDING WITHOUT LIMITATION, ANY WARRANTY OF MERCHANTABILITY, TITLE,
  NON-INFRINGEMENT AND FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL
  TEXAS INSTRUMENTS OR ITS LICENSORS BE LIABLE OR OBLIGATED UNDER CONTRACT,
  NEGLIGENCE, STRICT LIABILITY, CONTRIBUTION, BREACH OF WARRANTY, OR OTHER
  LEGAL EQUITABLE THEORY ANY DIRECT OR INDIRECT DAMAGES OR EXPENSES
  INCLUDING BUT NOT LIMITED TO ANY INCIDENTAL, SPECIAL, INDIRECT, PUNITIVE
  OR CONSEQUENTIAL DAMAGES, LOST PROFITS OR LOST DATA, COST OF PROCUREMENT
  OF SUBSTITUTE GOODS, TECHNOLOGY, SERVICES, OR ANY CLAIMS BY THIRD PARTIES
  (INCLUDING BUT NOT LIMITED TO ANY DEFENSE THEREOF), OR OTHER SIMILAR COSTS.

  Should you have any questions regarding your right to use this Software,
  contact Texas Instruments Incorporated at www.TI.com.
**************************************************************************************************/

#ifndef HAL_BOARD_CFG_H
#define HAL_BOARD_CFG_H

/*
 *     =============================================================
 *     |        Chipcon SmartRF05EB Evaluation Board, plus         |
 *     |            Texas Instruments CC2530EM Evaluation Module   |
 *     | --------------------------------------------------------- |
 *     |  mcu   : 8051 core                                        |
 *     |  clock : 32MHz                                            |
 *     =============================================================
 */


/* ------------------------------------------------------------------------------------------------
 *                                           Includes
 * ------------------------------------------------------------------------------------------------
 */

#include "hal_mcu.h"
#include "hal_defs.h"
#include "hal_types.h"

/* ------------------------------------------------------------------------------------------------
 *                                       CC2590/CC2591 support
 *
 *                        Define HAL_PA_LNA_CC2590 if CC2530+CC2590EM is used
 *                        Define HAL_PA_LNA if CC2530+CC2591EM is used
 *                        Note that only one of them can be defined
 * ------------------------------------------------------------------------------------------------
 */
#define xHAL_PA_LNA
#define xHAL_PA_LNA_CC2590


/* ------------------------------------------------------------------------------------------------
 *                                       Board Indentifier
 *
 *      Define the Board Identifier to HAL_BOARD_CC2530EB_REV13 for SmartRF05 EB 1.3 board
 * ------------------------------------------------------------------------------------------------
 */

#if !defined (HAL_BOARD_CC2530EB_REV17) && !defined (HAL_BOARD_CC2530EB_REV13)
  #define HAL_BOARD_CC2530EB_REV17
#endif

/* ------------------------------------------------------------------------------------------------
 *                                          Clock Speed
 * ------------------------------------------------------------------------------------------------
 */
#define HAL_CPU_CLOCK_MHZ     32

/* 32 kHz clock source select in CLKCONCMD */
#if !defined (OSC32K_CRYSTAL_INSTALLED) || (defined (OSC32K_CRYSTAL_INSTALLED) && (OSC32K_CRYSTAL_INSTALLED == TRUE))
  #define OSC_32KHZ  0x00 /* external 32 KHz xosc */
#else
  #define OSC_32KHZ  0x80 /* internal 32 KHz rcosc */
#endif

/* ------------------------------------------------------------------------------------------------
 *                                       LED Configuration
 * ------------------------------------------------------------------------------------------------
 */

#if defined (HAL_BOARD_CC2530EB_REV17) && !defined (HAL_PA_LNA) && !defined (HAL_PA_LNA_CC2590)
  #define HAL_NUM_LEDS            3
#elif defined (HAL_BOARD_CC2530EB_REV13) || defined (HAL_PA_LNA) || defined (HAL_PA_LNA_CC2590)
  #define HAL_NUM_LEDS            1
#else
  #error Unknown Board Indentifier
#endif

#define HAL_LED_BLINK_DELAY()   st( {
      volatile uint32 i; for (i=0; i<0x5800; i++) {
      }; } )

/* 1 - Green */
/*官方
#define LED1_BV           BV(0)
#define LED1_SBIT         P1_0
#define LED1_DDR          P1DIR
*/
/*D2  Luke  */
#define LED1_BV           BV(0)
#define LED1_SBIT         P0_0
#define LED1_DDR          P0DIR

#define LED1_POLARITY     ACTIVE_HIGH

/*D3  Luke*/
  #define LED2_BV           BV(0)
  #define LED2_SBIT         P2_0
  #define LED2_DDR          P2DIR

  #define LED2_POLARITY     ACTIVE_HIGH

#ifdef HAL_BOARD_CC2530EB_REV17
 
/* 2 - Red */
/*官方
  #define LED2_BV           BV(1)
  #define LED2_SBIT         P1_1
  #define LED2_DDR          P1DIR
*/


  /* 3 - Yellow */
  #define LED3_BV           BV(4)
  #define LED3_SBIT         P1_4
  #define LED3_DDR          P1DIR
  #define LED3_POLARITY     ACTIVE_HIGH
#endif

/* ------------------------------------------------------------------------------------------------
 *                                    Push Button Configuration
 * ------------------------------------------------------------------------------------------------
 */

#define ACTIVE_LOW        !
#define ACTIVE_HIGH       !!    /* double negation forces result to be '1' */

/* S1 官方
#define PUSH1_BV          BV(1)
#define PUSH1_SBIT        P0_1
*/
/*S1 luke */
#define PUSH1_BV          BV(4)
#define PUSH1_SBIT        P0_4

#ifdef HAL_BOARD_CC2530EB_REV17
  #define PUSH1_POLARITY    ACTIVE_HIGH
#elif defined (HAL_BOARD_CC2530EB_REV13)
  #define PUSH1_POLARITY    ACTIVE_LOW
#else
  #error Unknown Board Indentifier
#endif

/* Joystick Center Press */
#define PUSH2_BV          BV(0)
//#define PUSH2_SBIT        P2_0
#define PUSH2_POLARITY    ACTIVE_HIGH 

/* ------------------------------------------------------------------------------------------------
 *                         OSAL NV implemented by internal flash pages.
 * ------------------------------------------------------------------------------------------------
 */

// Flash is partitioned into 8 banks of 32 KB or 16 pages.
#define HAL_FLASH_PAGE_PER_BANK    16
// Flash is constructed of 128 pages of 2 KB.
#define HAL_FLASH_PAGE_SIZE        2048
#define HAL_FLASH_WORD_SIZE        4

// CODE banks get mapped into the XDATA range 8000-FFFF.
#define HAL_FLASH_PAGE_MAP         0x8000

// The last 16 bytes of the last available page are reserved for flash lock bits.
#if defined NON_BANKED
#define HAL_FLASH_LOCK_BITS        16
#define HAL_NV_PAGE_END            30
#else
#define HAL_FLASH_LOCK_BITS        16
#define HAL_NV_PAGE_END            126
#endif

// Re-defining Z_EXTADDR_LEN here so as not to include a Z-Stack .h file.
#define HAL_FLASH_IEEE_SIZE        8
#define HAL_FLASH_IEEE_PAGE       (HAL_NV_PAGE_END+1)
#define HAL_FLASH_IEEE_OSET       (HAL_FLASH_PAGE_SIZE - HAL_FLASH_LOCK_BITS - HAL_FLASH_IEEE_SIZE)
#define HAL_INFOP_IEEE_OSET        0xC

#define HAL_NV_PAGE_CNT            6
#define HAL_NV_PAGE_BEG           (HAL_NV_PAGE_END-HAL_NV_PAGE_CNT+1)

// Used by DMA macros to shift 1 to create a mask for DMA registers.
#define HAL_NV_DMA_CH              0
#define HAL_DMA_CH_RX              3
#define HAL_DMA_CH_TX              4

#define HAL_NV_DMA_GET_DESC()      HAL_DMA_GET_DESC0()
#define HAL_NV_DMA_SET_ADDR(a)     HAL_DMA_SET_ADDR_DESC0((a))


/* ------------------------------------------------------------------------------------------------
 *                                            Macros
 * ------------------------------------------------------------------------------------------------
 */

/* ----------- Cache Prefetch control ---------- */
#define PREFETCH_ENABLE()     st( FCTL = 0x08; )
#define PREFETCH_DISABLE()    st( FCTL = 0x04; )

/* ----------- Board Initialization ---------- */
#if defined (HAL_BOARD_CC2530EB_REV17) && !