HEVC帧内/帧间/PCM模式选择过程

For inter coded CUs, the following mode decision process is conducted in the HM encoder. Please refer to contributions about early termination for Early_CU condition, CBF_Fast condition, and Early_SKIP condition.

1.         Coding costs (J_mode) for MODE_INTER with PART_2Nx2N is computed and J_modeis set to minimum CU coding cost J.

2.         Check if motion vector difference ofMODE_INTER with PART_2Nx2N is equal to (0, 0) and MODE_INTER with PART_2Nx2N contains no non-zero transform coefficients (Early_SKIP condition). If both are true, proceed to 17 with setting the best interim coding mode as MODE_SKIP. Otherwise, proceed to 3.

3.         Check if MODE_INTER with PART_2Nx2N contains no non-zero transform coefficients (CBF_Fast condition). If the condition is true, proceed to 17 with setting the best interim coding mode as MODE_INTER with PART_2Nx2N. Otherwise, proceed to 4.

4.         J_modefor MODE_SKIP is evaluated and J is set equal to J_mode if J_mode< J.

5.         Check if the current CU depth is maximum and the current CU size is not 8x8 when inter_4x4_enabled_flag is zero. If the conditions are true, proceed to 6. Otherwise, proceed to 7.

6.         J_modefor MODE_INTER with PART_NxN is evaluated and J is set equal to J_mode if J_mode< J. After that, check if MODE_INTER with PART_NxN contains no non-zero transform coefficients (CBF_Fast condition). If the condition is true, proceed to 17 with setting the best interim coding mode as MODE_INTER with PART_NxN. Otherwise, proceed to 7.

7.         J_modefor MODE_INTER with PART_Nx2N is evaluated and J is set equal to J_mode if J_mode< J. After that, check if MODE_INTER with PART_Nx2N contains no non-zero transform coefficients (CBF_Fast condition). If the condition is true, proceed to 17 with setting the best interim coding mode as MODE_INTER with PART_Nx2N. Otherwise, proceed to 8.

8.         J_mode for MODE_INTER with PART_2NxN is evaluated and J is set equal to J_mode if J_mode< J. After that, check if MODE_INTER with PART_2NxN contains no non-zero transform coefficients (CBF_Fast condition). If the condition is true, proceed to 17 with setting the best interim coding mode as MODE_INTER with PART_2NxN. Otherwise, proceed to 9.

9.         Invoke a process to determine AMP mode evaluation procedure specified in 4.6.2.3. Output of this process is assigned to TestAMP_Hor and TestAMP_Ver. TestAMP_Hor specifies whether horizontal AMP modes are tested with specific ME or tested with merge mode or not tested. TestAMP_Ver specifies whether vertical AMP modes are tested with specific ME or tested with merge mode or not tested.

10.      If TestAMP_Hor indicates that horizontal AMP modes are tested, MODE_INTER with PART_2NxnU is evaluated with procedure suggested by TestAMP_Hor and J is set equal to the resulting coding cost J_mode if J_mode< J. After that, check if MODE_INTER with PART_2NxnU contains no non-zero transform coefficients (CBF_Fast condition). If the condition is true, proceed to 17 with setting the best interim coding mode as MODE_INTER with PART_2NxnU. Otherwise, MODE_INTER with PART_2NxnD is evaluated with procedure suggested by TestAMP_Hor and J is set equal to the resulting coding cost J_mode if J_mode< J. After that, check if MODE_INTER with PART_2NxnD contains no non-zero transform coefficients (CBF_Fast condition). If the condition is true, proceed to 17 with setting the best interim coding mode as MODE_INTER with PART_2NxnD. Otherwise, proceed to 11.

11.      If TestAMP_Ver indicates that vertical AMP modes are tested, MODE_INTER with PART_nLx2N is evaluated with procedure suggested by TestAMP_Ver and J is set equal to the resulting coding cost J_mode if J_mode< J. After that, check if MODE_INTER with PART_nLx2N contains no non-zero transform coefficients (CBF_Fast condition). If the condition is true, proceed to 17 with setting the best interim coding mode as MODE_INTER with PART_nLx2N. Otherwise, MODE_INTER with PART_nRx2N is evaluated with procedure suggested by TestAMP_Ver and J is set equal to the resulting coding cost J_mode if J_mode< J. After that, check if MODE_INTER with PART_nRx2N contains no non-zero transform coefficients (CBF_Fast condition). If the condition is true, proceed to 17 with setting the best interim coding mode as MODE_INTER with PART_nRx2N. Otherwise, proceed to 12.

12.      MODE_INTRA with PART_2Nx2N is evaluated by invoking the process specified in 4.6.1, only when at least one or more non-zero transform coefficients can be found by using the best interim coding mode. J is set equal to the resulting coding cost J_mode if J_mode< J.

13.      Check if the current CU depth is maximum, If the condition is true, proceed to 14. Otherwise, proceed to 15.

14.      MODE_INTRA with PART_NxN is evaluated by invoking the process specified in 4.6.1, only when the current CU size is larger than minimum TU size. The resulting coding cost J_modeis set to J if J_mode< J.

15.      Check if the current CU size is greater than or equal to the minimum PCM mode size specified by the log2_min_pcm_coding_block_size_minus3 value of SPS parameter. If the condition is true, proceed to 16. Otherwise, proceed to 17.

16.      Check if any of the following conditions are true. If the condition is true, PCM mode is evaluated and J is set equal to the resulting coding cost J_mode if J_mode< J.

–           Bit cost of J is greater than that of the PCM sample data of the input image block.

–           J is greater than bit cost of the PCM sample data of the input image block multiplied by λ_mode.

17.      Update bit cost B_modeby adding bits for CU split flag and re-compute minimum coding cost J.

18.         Check if the best interim coding mode is MODE_SKIP (Early_CU condition). If the condition is true, do not proceed to the recursive mode decision at next CU level. Otherwise, go to next CU level of recursive mode decision if the current CU depth is not maximum.

 

转载于:https://www.cnblogs.com/dreamsyeah/p/5878453.html