以下技术应用于最优质的水果的鲜果篮
For this tutorial I'll demonstrate how to build a simple yet scalable highly available HTTP load balancer using HAProxy [1] and keepalived [2], then later I'll show how to front-end HAProxy with Pound [5] and implement SSL termination and redirect the insecure connections from port 80 to 443.
Let's assume we have two servers LB1 and LB2 that will host HAProxy and will be made highly available through the use of the VRRP protocol [3] as implemented by keepalived. LB1 will have an IP address of 192.168.29.129 and LB2 will have an IP address of 192.168.29.130. The HAProxy will listen on the "shared/floating" IP address of 192.168.29.100, which will be raised on the active LB1. If LB1 fails that IP will be moved and raised on LB2 with the help of keepalived.
We are also going to have two back-end nodes that run apache - WEB1 192.168.29.131 and WEB2 192.168.29.132 - that will be receiving traffic from the HAProxy using round-robing load-balancing algorithm.
First let's install keepalived on both LB1 and LB2. We can either get it from the EPEL repo, or install it from source.
12 |
|
Edit the configuration file on both servers to match except the priority parameter:
1234567891011121314151617181920 |
|
Add following firewall rule into /etc/sysconfig/iptables on both LBs.
-A INPUT -p vrrp -j ACCEPT
run "service iptables restart" on both LBs.
Save the config on both servers and start keepalived:
1 |
|
Now that keepalived is running check that LB1 has raised 192.168.29.100:
12 |
|
You can test if the IP will move from LB1 to LB2 by failing LB1 (shutdown or bring the network down) and running the above command on LB2.
Now that we have high availability of the IP resource we can install HAProxy on LB1 and LB2:
1 |
|
Edit the configuration file, and start HAProxy:
123456789101112131415161718192021222324252627282930313233343536373839 |
|
This is a very simplistic configuration that uses HTTP load-balancing with cookie prefixing. This is how it works:
- LB1 is VRRP master (keepalived), LB2 is backup. Both monitor the haproxy process, and lower their prio if it fails, leading to a failover to theother node.
- LB1 will receive clients requests on IP 192.168.29.100.
- both load-balancers send their checks from their native IP.
- if a request does not contain a cookie, it will be forwarded to a validserver
- in return, if a JESSIONID cookie is seen, the server name will be prefixedinto it, followed by a delimitor ('~')
- when the client comes again with the cookie "JSESSIONID=A~xxx", LB1 will know that it must be forwarded to server A. The server name will then be extracted from the cookie before it is sent to the server.
- if server "webA" dies, the requests will be sent to another valid serverand a cookie will be reassigned.
For more information and examples see [4].
Add the following into /etc/sysctl.conf on both LBs.
net.ipv4.ip_nonlocal_bind=1
run "sysctl -p" on both LBs
Let's start HA proxy on both LB's:
1 |
|
1234567 |
|
Now hit 192.168.29.100 in your browser and refresh few times. You should see both nodes rotating in a round-robin fashion.
Also test the HA setup by failing one of the LB servers making sure that you always get a response back from the back-end nodes. Do the same for the back-end nodes.
To send logs from HAProxy to syslog-ng add the following lines to the syslog-ng config file:
1234567891011 |
|
Installing pound is straight forward and can be done from a package or from source. Once installed the config file should look like this:
1234567891011121314151617181920212223242526272829 |
|
To make HAProxy forward all insecure connections from port 80 to port 443 all we need to do is create an access list that looks for the header that Pound inserts and if missing redirect the HTTP connections to Pound (listening on port 443).
The new config needs to look like this:
12345678910111213141516171819202122232425262728293031323334 |
|
To generate a self-signed cert to use in Pound run this:
1 |
|
Resources:
[1] http://haproxy.1wt.eu/
[2] http://www.keepalived.org/
[3] http://en.wikipedia.org/wiki/Virtual_Router_Redundancy_Protocol
[4] http://haproxy.1wt.eu/download/1.2/doc/architecture.txt
[5] http://www.apsis.ch/pound/
[5] http://www.apsis.ch/pound/