OSPF MGRE接口类型特殊区域综合实验

按照图中要求 划分IP地址
区域2的公网接口地址先配好 然后在区域2 开启MGRE

此时区域2tunnel 可通
区域1的接口地址和环回：
[R1-GigabitEthernet0/0/1]ip ad 172.16.16.129 29
[R1-LoopBack0]ip ad 172.16.17.1 25
[R2-GigabitEthernet0/0/1]ip address 172.16.16.130 29
[R2-LoopBack0]ip ad 172.16.17.129 25
[R3-GigabitEthernet0/0/0]ip ad 172.16.48.1 30
[R3-LoopBack0]ip ad 172.16.18.1 25
区域2
[R6-GigabitEthernet0/0/1]ip ad 172.16.32.1 30
[R11-LoopBack0]ip ad 172.16.33.1 25
[R11-GigabitEthernet0/0/0]ip ad 172.16.32.5 30
[R11-GigabitEthernet0/0/1]ip ad 172.16.32.2 30
区域3
[R7-GigabitEthernet0/0/1]ip ad 172.16.48.1 30
[R8-GigabitEthernet0/0/1]ip ad 172.16.48.2 30
[R8-GigabitEthernet0/0/0]ip ad 172.16.48.5 30
[R8-LoopBack0]ip ad 172.16.49.1 25
[R9-GigabitEthernet0/0/0]ip ad 172.16.48.6 30
区域4
[R9-LoopBack0]ip ad 172.16.65.1 25
[R9-GigabitEthernet0/0/1]ip ad 172.16.64.1 30
[R10-LoopBack0]ip ad 172.16.65.129 25
[R10-GigabitEthernet0/0/1]ip ad 172.16.64.2 30

配置完成后开启OSPF协议 在a0区域内关闭R567的DR选举 并修改接口类型为broadcast
最后R3为DR 邻居关系如图

在R12上进行RIP的重发布
[R12-ospf-1]import-route rip
在R9上建立多进程ospf与R10建邻
完成后进行路由汇总
[R3-ospf-1-area-0.0.0.1]abr-summary 172.16.16.0 255.255.240.0
[R6-ospf-1-area-0.0.0.2]abr-summary 172.16.32.0 255.255.240.0
[R7-ospf-1-area-0.0.0.3]abr-summary 172.16.48.0 255.255.240.0
[R12-ospf-1]asbr-summary 172.16.80.0 255.255.240.0
[R9-ospf-1]asbr-summary 172.16.64.0 255.255.240.0
进行特殊区域配置
[R2-ospf-1-area-0.0.0.1]stub
[R1-ospf-1-area-0.0.0.1]stub
[R3-ospf-1-area-0.0.0.1]stub no-summary
[R12-ospf-1-area-0.0.0.2]nssa
[R6-ospf-1-area-0.0.0.2]nssa no-summary
[R11-ospf-1-area-0.0.0.2]nssa

[R7-ospf-1-area-0.0.0.3]nssa no-summary
[R8-ospf-1-area-0.0.0.3]nssa
[R9-ospf-1-area-0.0.0.3]nssa
[R9-ospf-2]default-route-advertise R9给R10发布一条缺省
此时已全网可达
[R3-acl-basic-2000]rule permit source 172.16.0.0 0.0.255.255
[R3-GigabitEthernet0/0/1]nat outbound 2000
R7和R6同上做nat


均可访问R4环回