【无标题】光模块介绍（华视伟业HSION）

2.5G 1310nm Duplex SFP Transceiver Module

Features

 Operating data rate up to 2.125/2.5Gbps

 1310nm DFB LD Transmitter, 1310nm PIN-TIA

 Distance up to 20KM

 Single 3. 3V Power supply and TTL Logic Interface

 Duplex LC Connector Interface

 Hot Pluggable

 Operating Case Temperature：0℃~+70℃

 Compliant with MSA SFP Specification

 Digital diagnostic monitor interface compatible with SFF-8472 and DDM optional

Applications

 Fiber Channel Infrastructure

 STM-16 Optical interface

 ATM Switches and Routers

 SDH/SONET Switch Infrastructure

Product Description

The SFP SM series single mode transceivers is small form factor pluggable module for

bi-directional serial optical data communications. It is with the SFP 20-pin connector to allow hot

plug capability. This module is designed for single mode fiber and operates at a nominal

wavelength of 1310 nm.

The transmitter section uses a multiple quantum well laser and is a class 1 laser compliant

according to International Safety Standard IEC-60825. The receiver section uses an integrated

InGaAs detector preamplifier (IDP) mounted in an optical header and a limiting post-amplifier IC.

The SFP SM (I) series are designed to be compliant with SFF-8472 SFP Multi-source Agreement

(MSA).

Absolute Maximum Ratings

Parameter

Symbol

Min.

Max.

Unit

Storage Temperature

TS

-40

+85

°C

V1.2 2

Supply Voltage

VCC

-0.5

3.6

V

Recommended Operating Conditions

Parameter

Symbol

Min.

Typical

Max.

Unit

Operating Temperature

TA

0

+70

°C

Power Supply Voltage

VCC

3.15

3.3

3.45

V

Data Rate

2 Fiber Channel

2.125

Gbps

OC-48 / STM-16

2.488

Total Supply Current

ICC

300

mA

PERFORMANCE SPECIFICATIONS - ELECTRICAL

Parameter

Symbol

Min.

Typ.

Max.

Unit

Notes

TRANSMITTER

CML/PECL Inputs

(Differential)

Vin

400

1800

mVpp AC coupled inputs

Input Impedance

(Differential)

Zin

90

100

110

ohms

Rin > 100 kohms

@ DC

Tx_DISABLE Input Voltage

• High

2

3.45

V

Tx_DISABLE Input Voltage

• Low

0

0.8

V

Tx_FAULT Output Voltage

– High

Vcc-0.5

Vcc+0.3

V

Io = 400µA; Host

Vcc

Tx_FAULT Output Voltage

– Low

0

0.5

V

Io = -4.0mA

TX_Disable Assert Time

t_off

10

us

TX_Disable Negate Time

t_off

1

us

RECEIVER

CML Outputs (Differential)

Vout

370

1800

mVpp

AC coupled

outputs

Output Impedance

(Differential)

Zout

90

100

110

ohms

Rx_LOS Output Voltage -

High

Vcc-0.5

Vcc+0.3

V

lo = 400µA; Host

Vcc

Rx_LOS Output Voltage -

Low

0

0.8

V

lo = -4.0mA

Optical and Electrical Characteristics

Parameter

Symbol

Min.

Typical

Max.

Unit

9µm Core Diameter SMF

20

Km

Data Rate

2.5

2.67

Gbps

Transmitter

V1.2 3

Centre Wavelength

λC

1290

1310

1330

nm

Spectral Width (RMS)

σ

1

nm

Average Output Power

Pave

-6

0

dBm

Extinction Ratio

Ext

8.2

dB

Output Optical Eye

IEEE 802.3ah

Receiver

Centre Wavelength

λC

1260

1310

1610

nm

Receiver Sensitivity

PIN

-18

dBm

Output Differential Impedance

90

100

110

Ω

Data Output Swing Differential

VOUT

370

2000

mV

Receiver Overload

Pmax -PIN

-3

dBm

Optical Rise/Fall Time

Tr/tf

160

180

ps

LOS De-Assert

LOSD

-19

dBm

LOS Assert

LOSA

-35

dBm

SFP Transceiver Electrical Pad Layout

VeeR

VeeT

Tx_Fault

Tx_Disable

MOD_DEF(2)

MOD_DEF(1)

MOD_DEF(0)

Rate Select

LOS

VeeR

VeeT

TD-

TD+

VeeT

VccT

VccR

VeeR

RD+

RD-

VeeR

1

2

3

4

5

7

8

9

10

11

12

13

14

15

16

17

18

19

20

6

Towards Bezel

Towards ASIC

Figure 1 Transceiver pin descriptions

Pin Function Definitions

Pin

Number

Name

FUNCTION

Plug Seq.

Notes

1

VeeT

Transmitter Ground

1

2

TX Fault

Transmitter Fault

Indication

3

Note 1

V1.2 4

3

TX Disable

Transmitter Disable

3

Note 2, Module disables on high or

open

4

MOD-DEF2

Module Definition 2

3

Note 3, Data line for Serial ID.

5

MOD-DEF1

Module Definition 1

3

Note 3, Clock line for Serial ID.

6

MOD-DEF0

Module Definition 0

3

Note 3, Grounded within the

module.

7

Rate Select

Not Connect

3

Function not available

8

LOS

Loss of Signal

3

Note 4

9

VeeR

Receiver Ground

1

Note 5

10

VeeR

Receiver Ground

1

Note 5

11

VeeR

Receiver Ground

1

Note 5

12

RD-

Inv. Received Data Out

3

Note 6

13

RD+

Received Data Out

3

Note 7

14

VeeR

Receiver Ground

1

Note 5

15

VccR

Receiver Power

2

3.3 ± 5%, Note 7

16

VccT

Transmitter Power

2

3.3 ± 5%, Note 7

17

VeeT

Transmitter Ground

1

Note 5

18

TD+

Transmit Data In

3

Note 8

19

TD-

Inv. Transmit Data In

3

Note 8

20

VeeT

Transmitter Ground

1

Note 5

Notes:

1. TX Fault is an open collector/drain output, which should be pulled up with a 4.7K –

10KΩ resistor on the host board. Pull up voltage between 2.0V and VccT, R+0.3V. When high, output indicates a

laser fault of some kind. Low indicates normal operation. In the low state, the output will be pulled to < 0.8V.

2. TX disable is an input that is used to shut down the transmitter optical output. It is pulled up within the module

with a 4.7 – 10 K Ω resistor. Its states are:



Low (0 – 0.8V): Transmitter on



(>0.8, < 2.0V): Undefined



High (2.0 – 3.465V): Transmitter Disabled



Open: Transmitter Disabled

3. Mod-Def 0,1,2. These are the module definition pins. They should be pulled up with a 4.7K – 10KΩresistor on

the host board. The pull-up voltage shall be VccT or VccR (see Section IV for further details). Mod-Def 0 is

grounded by the module to indicate that the module is present Mod-Def 1 is the clock line of two wire serial

interface for serial ID Mod-Def 2 is the data line of two wire serial interface for serial ID

4. LOS (Loss of Signal) is an open collector/drain output, which should be pulled up with a 4.7K – 10KΩ resistor.

Pull up voltage between 2.0V and VccT, R+0.3V. When high, this output indicates the received optical power is

V1.2 5

below the worst-case receiver sensitivity (as defined by the standard in use). Low indicates normal operation. In

the low state, the output will be pulled to < 0.8V.

5. VeeR and VeeT may be internally connected within the SFP module.

6. RD-/+: These are the differential receiver outputs. They are AC coupled 100Ω differential lines which should be

terminated with 100Ω (differential) at the user SERDES. The AC coupling is done inside the module and is thus not

required on the host board. The voltage swing on these lines will be between 370 and 2000 mV differential (185

–1000 mV single ended) when properly terminated.

7. VccR and VccT are the receiver and transmitter power supplies. They are defined as 3.3V ±5% at the SFP

connector pin. Maximum supply current is 300mA. Recommended host board power supply filtering is shown below.

Inductors with DC resistance of less than 1 ohm should be used in order to maintain the required voltage at the SFP

input pin with 3.3V supply voltage. When the recommended supply-filtering network is used, hot plugging of the

SFP transceiver module will result in an inrush current of no more than 30mA greater than the steady state value.

VccR and VccT may be internally connected within the SFP transceiver module.

8. TD-/+: These are the differential transmitter inputs. They are AC-coupled, differential lines with 100Ω

differential termination inside the module. The AC coupling is done inside the module and is thus not required on

the host board. The inputs will accept differential swings of 500 – 2400 mV (250 – 1200mV single-ended), though

it is recommended that values between 500 and 1200 mV differential (250 – 600mV single-ended) be used for best

EMI performance.

Digital Diagnostic Memory Map

V1.2 6

Figure 2 Digital Diagnostic Memory Map

Recommend Circuit Schematic

VCC=3.3V

RES1

Host Board

Tx_Disable

RES1

Tx_Fault

0.01µf

0.01µf

Laser

Driver

TD+

TD-

RD+

RD+

0.01µf

0.01µf

Rx_LOS

Mod def2

Mod def1

Mod def0

EEPROM

Rx_LOS

Photodiode

RES 1 = 4.7k to 10k

100Ω

SFP Module

VCC(+3.3V)

VCC(+3.3V)

RES1X3

RES1

Vcc=3.3V

100Ω

PECL

PECL

2x150Ω

Figure 3 Recommend Circuit Schematic

Mechanical Specifications

Uint:mm

Amplifier@TOC

欢迎使用Markdown编辑器

你好！ 这是你第一次使用 Markdown编辑器 所展示的欢迎页。如果你想学习如何使用Markdown编辑器, 可以仔细阅读这篇文章，了解一下Markdown的基本语法知识。

新的改变

我们对Markdown编辑器进行了一些功能拓展与语法支持，除了标准的Markdown编辑器功能，我们增加了如下几点新功能，帮助你用它写博客：

1. 全新的界面设计 ，将会带来全新的写作体验；
2. 在创作中心设置你喜爱的代码高亮样式，Markdown 将代码片显示选择的高亮样式 进行展示；
3. 增加了 图片拖拽 功能，你可以将本地的图片直接拖拽到编辑区域直接展示；
4. 全新的 KaTeX数学公式 语法；
5. 增加了支持甘特图的mermaid语法¹ 功能；
6. 增加了 多屏幕编辑 Markdown文章功能；
7. 增加了 焦点写作模式、预览模式、简洁写作模式、左右区域同步滚轮设置 等功能，功能按钮位于编辑区域与预览区域中间；
8. 增加了 检查列表 功能。

功能快捷键

撤销：Ctrl/Command + Z
重做：Ctrl/Command + Y
加粗：Ctrl/Command + B
斜体：Ctrl/Command + I
标题：Ctrl/Command + Shift + H
无序列表：Ctrl/Command + Shift + U
有序列表：Ctrl/Command + Shift + O
检查列表：Ctrl/Command +