http://topic.csdn.net/t/20020822/00/960071.html
Awdflash.exe的各种参数使用说明:
/?:显示帮助信息
/py:自动完成BIOS的刷新任务
/sy:备份原来的BIOS到磁盘
/sb:在升级BIOS时强行跳过BootBlock模块
/cp:在刷新结束后清除即插即用数据(ESCD)
/cd:在刷新BIOS结束后清除DMI数据
/r:在刷新BIOS结束后自动重启动
/pn:不运行升级程序
/sn:不备份系统老的BIOS文件
/sd:保存DMI数据到一个文件
/cks:在更新BIOS时显示备份文件的数据
/tiny:只占用很少的内存
/e:刷新结束后自动回到DOS命令行状态
/f:刷新时使用原来的BIOS数据
/ld:在刷新结束后清除CMOS数据并且不重新引导系统
/cksxxxx:将老的备份BIOS文件与新的BIOS文件进行比较校验
想要自动刷新回去再软盘的autoexec.bat中输入:
Awdflash.exe *.bin /sn /py
如果不行,就要找维修点了
================
有软驱吗?
可以制作BIOS刷新软盘~
首先,如果你的系统处于超频状态,请先恢复正常,然后关闭BIOS设置中所有有关电源管理的项目,并关闭BIOS缓存(“sysetm BIOS Cacheable”)和显卡BIOS缓存(“Video BIOS Cacheable”)。
然后在DOS下插入一张已经格式化的软盘,用“SYS C A”命令将系统文件复制到A盘,然后把Awardfalsh工具(一般主板配套光盘里有)和最新的BIOS文件(假设为newbios.bin)一起复制到A盘,最后在软盘上创建一个批处理文件autoexec.bat,内容如下:
@echo off(回车)
if exist oldbios.bin goto awdflash.exe newbios.bin oldbios.bin/py/sy/cc/cp/cd/sb/rgoto(回车)
endawdflash.exe oldbios.bin/py/sy/cc/cp/cd/sb/rend
好了,现在软盘上已经有了以下文件:Awardfalsh.exe、newbios.bin、autoexec.bat、msdos.sys、io.sys和command.com。用软盘启动计算机后,计算机将自动刷新BIOS了,如果刷新失败也可以用这张软盘来恢复以前的BIOS。
注意:AwardFalsh刷新工具版本必须在V7.70以上,刷新后将软盘从软驱中取出,并进入BIOS设置从新调整即可。
===============
BIOS is the basic software of PC. If it is crashed, You could not start the PC.
If you can get the bios chip out(See whether there is a socket in your mother board, usually 32 pins), I can't help you flash it(Use external flash device).
(Believe me. I am a firmware engineer focusing on BIOS development...).
是BIOS,不是CMOS, CMOS可以放电,BIOS坏了只能拆下来才能恢复。 有socket的容易拆。没有socket的只能用焊枪拆了,然后用外面的flash device burn BIOS binary image 进去恢复。。。
一般PC/笔记本 BIOS 不会有socket的,节约成本, 我估计只有用焊枪了。
Sorry in Company right now, no Chinese input.
BIOS is stored in NOR flash ROM chip, it don't need battery to keep information. CMOS is
another RAM chip, it need battery to keep configuration information. These data in CMOS are
not important data, once BIOS is running, they can be resumed back to default value. Then
you can re-config them and save them into CMOS.
When PC is power-on, CPU will copy BIOS software from ROM into system memory and run it.
BIOS software will read config data from CMOS to initialize hardware...
LZ Notebook's BIOS software in ROM chip is crashed because of burning error. So it can't
boot notebook.
I just saw the datasheet. Maybe it has a solution.
See page 98.
Repairing the BIOS IC
(Service Partners Only)
The notebook’s BIOS IC cannot be replaced separately. If it is defective, you must replace
the
motherboard. In some cases, however, you might be able to reprogram a malfunctioning BIOS IC
using either e-DiagTools for Windows, a BIOS floppy disk, or a Crisis Recovery floppy disk.
You have to have BIOS floppy disk, or a Crisis Recovery floppy disk. Then press Fn+B to
power-on. Then CPU will read floppy software as BIOS instead of reading BIOS chip.
Unfortunately, if you have no BIOS floppy disk, or a Crisis Recovery floppy disk.
you only have to get the chip out...
Good luck!