写个学校中兴实验室的实验手册

上机实验

 

 

本章共有10个上机实验小节。默认读者已经掌握了IP地址的作用、VLAN3层交换和2层交换的区别、常用路由协议等知识。如还不是十分了解,请在阅读本章前参考其他书籍了解并学习他们。

本章中所有实验在一般情况下都应在PC端通过Console线与设备相连进行操作(这种操作方法请参见2.4节)。但是由于这样做不便于操作管理而且不易合理分配资源,所以本章所有实验默认情况下均使用CCS2000客户端进行远程控制操作(这种操作方法请参见1.5节,其实这种连接方法的控制效果和本地串口连接设备Console口相同),请同学先行掌握他的使用。CCS2000的一个缺点是无法用TAB键缺省输入,可以用CCS2000对设备进行初始化操作后再用Telnet进行远程管理。

 

4.1  3928交换机的基本操作

 

3928交换机是中兴公司的3层交换设备。使用CCS2000客户端将1#5#中任意1台空闲的3928加入到队列中,连接设备串口。

 

基本操作:

3928#show running-config             //查看配置信息

3928#show logfile                   //查看交换机日志

3928#show logging alarm             //查看系统警告信息

3928>enable                       //进入特权模式

3928#configure terminal              //进入全局配置模式

3928(config)#enable secret zxr10       //设置enable密码为zxr10

3928(config)#username zxr10 password zxr10     // 配置一个用户名密码都是zxr10的用户,

                                             远程登陆可用

3928(config)#who                 //查看当前用户

3928(config)#show username      //查看配置的用户信息,可显示用户名和密码

3928(config)#interface           //进入端口配置模式

3928(config-if)#shutdown/no shutdown    //关闭/打开以太网端口

3928(config-if)#negotiation auto/no negotiation auto    //打开/关闭以太网端口自动协商

3928(config-if)#duplex            //设置以太网端口双工模式

3928(config-if)#speed            //设置以太网端口速率

3928(config-if)#flowcontrol        //设置以太网端口流量控制

3928(config-if)#jumbo-frame/no jumbo-frame      //允许/禁止巨帧通过以太网端口

3928(config-if)#byname           //设置端口别名

3928(config-if)#broadcast-limit        //设置以太网口广播风暴抑制,当设置为100M时,表示不抑制

 

 

4.2  1800路由器的基本操作

 

    使用CCS2000客户端将1#5#中任意1台空闲的1800加入到队列中,连接设

备串口。

 

基本操作:

1800>enable                         //进入特权配置模式/

1800#show ip route                   //查看路由表

1800#configure terminal               //进入全局配置模式

1800(config)#show running-config       //查看当前路由器配置信息

1800(config)#enable secret zxr10        //设置enable密码为zxr10

1800(config)#username zxr10 password zxr10  //将远程telnet用户名密码都设为zxr10

1800(config)#show interface            //查看所有端口信息

1800(config)#show interface fei_2/1      //查看端口fei_2/1的信息

1800(config)#interface                 //进入端口配置模式

1800(config-if)#arp                    //set ARP timeout

1800(config-if)#backup                 //backup a line

1800(config-if)#clear                   //clear MAC binding

1800(config-if)#custom-queue-list        //assign a custom queue list to an interface

1800(config-if)#description              //interface specific descrition

1800(config-if)#dhcp                   //set dhcp configure

1800(config-if)#duplex                 //configure duplex operation

1800(config-if)#end                    //exit to exec mode

1800(config-if)#exit                    //exit from interface configuration mode

1800(config-if)#h323-gateway           //configure H323 Gateway

1800(config-if)#interface               //set an interface characters

1800(config-if)#ip                     //interface Internet Protocol config commands

1800(config-if)#isis                    //ISIS interface commands

1800(config-if)#keepalive               //keepalive period(default 10 seconds)

1800(config-if)#load-interval            //set the interface statistics interval

1800(config-if)#mpls                  //configure MPLS interface parameters

1800(config-if)#no                    //Negate a command or set its defaults

1800(config-if)#peer                  //peer parameters for interfaces

1800(config-if)#priority-group           //assign a priority group to an interface

1800(config-if)#rate-limit               //rate limit

1800(config-if)#rmon                  //Remote Monitoring

1800(config-if)#set                   //binding MAC address

1800(config-if)#shutdown              //shutdown the selected interface

1800(config-if)#speed                 //configure speed operation

1800(config-if)#user-interface           //user interface

1800(config-if)#vrrp                   //VRRP interface configuration commands

1800(config-if)#description ZTE          //接口描述信息

 

 

4.3  2826交换机VLAN配置

 

2826交换机是中兴公司的2层交换设备。使用CCS2000客户端将1#5#中任意2台空闲的2826加入到队列中,连接设备串口。分别命名为2826A2826B,用交叉网线连接两台交换机以太网口。任意4PC编号PC1PC4PC1PC2配线架上的接口用网线连接2826A的以太网口,PC3PC4连接2826B。具体实验拓扑图如下:

 

2826A具体配置:

zte>en

zte#conf  t

zte(cfg)#hostname 2826A

2826A(cfg)#set vlan 2 add port 16 tag          //VLAN 2中加入端口16,并打tag

2826A(cfg)#set vlan 2 add port 1 untag         //VLAN 2中加入端口1,不打tag

2826A(cfg)#set vlan 3 add port 16 tag

2826A(cfg)#set vlan 3 add port 2 untag

2826A(cfg)#set port 1 pvid 2                 //设置端口1PVID2

2826A(cfg)#set port 2 pvid3

2826A(cfg)#set vlan 2-3 enable               //使能VLAN 23

 

2826B具体配置:

zte>en

zte#conf  t

zte(cfg)#hostname 2826B

2826B(cfg)#set vlan 2 add port 16 tag          //VLAN 2中加入端口16,并打tag

2826B(cfg)#set vlan 2 add port 2 untag         //VLAN 2中加入端口1,不打tag

2826B(cfg)#set vlan 3 add port 16 tag

2826B(cfg)#set vlan 3 add port 4 untag

2826B(cfg)#set port 2 pvid 2                 //设置端口1PVID2

2826B(cfg)#set port 4 pvid3

2826B(cfg)#set vlan 2-3 enable               //使能VLAN 23

 

实验结果验证:

PC1PC3能够互相ping通;

PC2PC4能够互相ping通;

PC1PC4不能互相ping通,PC2PC3不能互相ping通。

 

实验结论:

同一vlan下的设备可以互通,不通vlan下的设备不能互通;通过端口打TAG可以传递多个VLAN信息。

 

 

4.4  3928交换机VLAN配置

 

3928交换机是中兴公司的3层交换设备。使用CCS2000客户端将1#5#中任意2台空闲的3928加入到队列中,连接设备串口。分别命名为3928A3928B,用交叉网线连接两台交换机快速以太网口。任意4PC编号PC1PC4PC1PC2配线架上的接口用网线连接3928A的快速以太网口,PC3PC4连接3928B。具体实验拓扑图如下:

3928A具体配置:

3928A(config)#vlan 10                     //创建vlan 10

3928A(config-vlan)#exit

3928A(config)#vlan 20

3928A(config-vlan)#exit

3928A(config)#interface fei_1/1

3928A(config-if)#switchport access vlan 10    //把端口fei_1/1加入vlan 10,模式为access

3928A(config-if)#exit

3928A(config)#interface fei_1/2

3928A(config-if)#switchport access vlan 20    //把端口fei_1/2加入vlan 20,模式为access

3928A(config-if)#exit

3928A(config)#interface fei_1/16

3928A(config-if)#switchport mode trunk

3928A(config-if)#switchport trunk vlan 10     //把端口fei_1/16trunk模式加入vlan1020

3928A(config-if)#switchport trunk vlan 20

 

 

 

3928B具体配置:

3928A(config)#vlan 10                     //创建vlan 10

3928A(config-vlan)#exit

3928A(config)#vlan 20

3928A(config-vlan)#exit

3928A(config)#interface fei_1/1

3928A(config-if)#switchport access vlan 10    //把端口fei_1/1加入vlan 10,模式为access

3928A(config-if)#exit

3928A(config)#interface fei_1/2

3928A(config-if)#switchport access vlan 20    //把端口fei_1/2加入vlan 20,模式为access

3928A(config-if)#exit

3928A(config)#interface fei_1/16

3928A(config-if)#switchport mode trunk

3928A(config-if)#switchport trunk vlan 10     //把端口fei_1/16trunk模式加入vlan1020

3928A(config-if)#switchport trunk vlan 20

 

实验结果验证:

PC1PC2不能互相ping通,PC3PC4不能互相ping通;

PC1PC3能互相ping通,PC2PC4能互相ping通。

 

实验结论:

    同一vlan下的设备可以互通,不同vlan下的设备不能互通;通过trunk端口可以实现vlan透传。

 

 

4.5  3928交换机VLAN路由实验

 

本实验用两种不同的方法实现不同VLAN间可通信。

 

方法1:使用单臂路由

使用CCS2000客户端将1#5#中任意1台空闲的39281台空闲的1800连接设备串口。用网线连接两台设备的快速以太网口。任意2PC配线架上的接口用网线连接3928的快速以太网口。具体实验拓扑图如下:

 

1800具体配置:

1800(config)#interface fei_0/1.1                     //创建子接口

1800(config-subif)#encapsulation dot1q 20            //封装VLAN ID

1800(config-subif)#ip address 10.40.50.1 255.255.255.192

1800(config-subif)#exit

1800(config)#interface fei_0/1.2

1800(config-subif)#encapsulation dot1q 30

1800(config-subif)#ip address 10.40.50.65 255.255.255.192

1800(config-subif)#exit

 

3982具体配置:

3928(config)#vlan 20                            //创建VLAN 20

3928(config-vlan)#exit

3928(config)#vlan 30

3928(config-vlan)#exit

3928(config)#interface fei_1/1

3928(config-if)#switchport access vlan 20           //端口fei_1/1 access方式加入

3928(config-if)#exit

3928(config)#interface fei_1/2

3928(config-if)#switchport access vlan 30

3928(config-if)#exit

3928(config)#interface fei_1/3

3928(config-if)#switchport mode trunk             //修改端口的链路类型为trunk模式

3928(config-if)#switchport trunk vlan 20            //端口fei_1/3trunk方式加入vlan20

3928(config-if)#switchport trunk vlan 30            //端口fei_1/3trunk方式加入vlan30

3928(config-if)#exit

 

实验结果验证:

两台电脑可以互相ping通。

 

方法2:三层交换机

使用CCS2000客户端将1#5#中任意1台空闲的3928连接设备串口。任意2PC配线架上的接口用网线连接3928的快速以太网口。具体实验拓扑图如下:

 

3928具体配置:

3928(config)#vlan 20

3928(config-vlan)#exit

3928(config)#vlan 30

3928(config-vlan)#exit

3928(config)#interface fei_1/1

3928(config-if)#switchport access vlan 20

3928(config-if)#exit

3928(config)#interface fei_1/2

3928(config-if)#switchport access vlan 30

3928(config-if)#exit

3928(config)#interface vlan 20

3928(config-if)#ip address 10.40.50.1 255.255.255.192   //VLAN接口上配置IP

3928(config-if)#exit

3928(config)#interface vlan 30

3928(config-if)#ip address 10.40.50.65 255.255.255.192

3928(config-if)#exit

 

实验结果验证:

两台电脑可以互相ping通。

 

实验结论:

    单臂路由和三层交换方式可以实现不同VLAN的互通。

 

 

4.6  交换机静态路由实验

 

使用CCS2000客户端将1#5#中任意2台空闲的3928加入到队列中,连接设备串口。分别命名为3928A3928B,用交叉网线连接两台交换机快速以太网口。任意2PC编号PC1PC2,分别连接3928A3928B的快速以太网口。具体实验拓扑图如下:

3928A具体配置:

3928A(config)#vlan 2

3928A(config-vlan)#switchport pvid fei_2/1              //PC1

3928A(config-vlan)#exit

3928A(config)#interface vlan 2

3928A(config-if)#ip add 10.1.3.1 255.255.255.0

3928A(config-if)#exit

3928A(config)#interface fei_3/1                       //3928B

3928A(config-if)#switchport access vlan 3

3928A(config-if)#exit

3928A(config)#interface vlan 3

3928A(config-if)#ip address 192.168.1.1 255.255.255.252

3928A(config-if)#exit

3928A(config)#ip route 10.2.1.0 255.255.255.0 192.168.1.2

3928A(config)#ip route 10.2.2.0 255.255.255.0 192.168.1.2

3928A(config)#ip route 10.2.3.0 255.255.255.0 192.168.1.2

(以上三行命令可用以下缺省路由命令代替:

3928A(config)#ip route 0.0.0.0 0.0.0.0 192.168.1.2)

 

 

3928B具体配置

3928B(config)#vlan 2

3928B(config-vlan)#switchport pvid fei_2/1              //PC2

3928B(config-vlan)#exit

3928B(config)#interface vlan 2

3928B(config-if)#ip add 10.2.3.1 255.255.255.0

3928B(config-if)#exit

3928B(config)#interface fei_3/1                       //3928A

3928B(config-if)#switchport access vlan 3

3928B(config-if)#exit

3928B(config)#interface vlan 3

3928B(config-if)#ip address 192.168.1.2 255.255.255.252

3928B(config-if)#exit

3928B(config)#ip route 10.1.1.0 255.255.255.0 192.168.1.1

3928B(config)#ip route 10.1.2.0 255.255.255.0 192.168.1.1

3928B(config)#ip route 10.1.3.0 255.255.255.0 192.168.1.1

(以上三行命令可用以下缺省路由命令代替:

3928B(config)#ip route 0.0.0.0 0.0.0.0 192.168.1.1)

 

实验结果验证:

显示路由表(show ip route)查看出现那些路由;

观察PC1PC2直接能否ping通,有无丢包。

 

 

4.7  1800路由器静态路由实验

 

使用CCS2000客户端将1#5#中任意2台空闲的1800加入到队列中,连接设备串口。分别命名为R1R2,用交叉网线连接两台路由器快速以太网口。任意3PC编号PC1PC2PC3PC1连接R1的快速以太网口,PC2,PC3连接R2的快速以太网口。具体实验拓扑图如下:

 

R1具体配置:

R1(config)#interface fei_1/1               //该端口接R2

R1(config-if)#ip address 10.1.1.2 255.255.255.0

R1(config-if)#exit

R1(config)#interface fei_1/2               //该端口接PC1

R1(config-if)#ip address 30.1.1.1 255.255.255.0

R1(config-if)#exit

R1(config)#ip route 0.0.0.0 0.0.0.0 10.1.1.1   //配置缺省路由

R2具体配置:

R2(config)#interface fei_1/1               //该端口接R1

R2(config-if)#ip address 10.1.1.1 255.255.255.0

R2(config-if)#exit

R2(config)#interface fei_1/2               //该端口接PC2

R2(config-if)#ip address 20.1.1.1 255.255.255.0

R2(config-if)#exit

R2(config)#interface fei_1/3               //该端口接PC3

R2(config-if)#ip address 40.1.1.1 255.255.255.0

R2(config-if)#exit

R2(config)#ip route 40.1.1.1 255.255.255.0 10.1.1.2  //配置静态路由

 

实验结果验证:

R1#show ip route            // 查看R1路由表,static表示静态路由

 

IPv4 Routing Table:

Dest           MASK          GW        Interface         Owner   pri     metric

0.0.0.0       0.0.0.0         10.1.1.2        fei_1/1         static     1        0

10.1.1.0     255.255.255.0    10.1.1.2        fei_1/1         direct     0        0

10.1.1.2    255.255.255.255   10.1.1.2        fei_1/1         address   0        0

30.1.1.0     255.255.255.0    30.1.1.1        fei_1/2         direct     0        0

30.1.1.1    255.255.255.0     30.1.1.1        fei_1/2         address   0        0

 

R2#show ip route

 

IPv4 Routing Table:

Dest         MASK        GW     Interface      Owner   pri     metric

10.1.1.0   255.255.255.0   10.1.1.1    fei_0/1       direct     0        0

10.1.1.1  255.255.255.255  10.1.1.2    fei_0/1       address   0        0

20.1.1.0    255.255.255.0   20.1.1.1   fei_1/1       direct     0        0

20.1.1.1  255.255.255.255  20.1.1.1    fei_1/1       address   0        0

30.1.1.0   255.255.255.0   10.1.1.1    fei_0/1       static     1

40.1.1.0   255.255.255.0   40.1.1.1    fei_2/1       direct     0        0

40.1.1.1   255.255.255.0   40.1.1.1    fei_2/1       address   0

 

实验结论:

PC1可以和PC2PC3互通。

静态路由是网络管理员通过配置命令指定到路由表中的路由信息,它不像动态路由那样根据路由算法建立路由表。当配置动态路由时,有时需要把整个Internet的路由信息发送到一个路由器中,使该路由器难以负荷,此时就可以使用静态路由来解决这个问题。使用静态路由只需要较少的配置就可以避免动态路由的使用。但是在有多个路由器、多条路径的路由环境中,配置静态路由将变得很复杂。

 

 

4.8  1800路由器RIP实验

 

  使用CCS2000客户端将1#5#中任意2空闲的1800加入到队列中,连接设备串口。分别命名为R1R2,用交叉网线连接两台路由器快速以太网口。任意2PC编号PC1PC2PC1连接R1的快速以太网口,PC2连接R2的快速以太网口。具体实验拓扑图如下:

R1具体配置:

R1(config)#interface fei_1/1

R1(config-if)#ip address 192.168.1.1 255.255.255.0

R1(config-if)#exit

R1(config)#interface fei_0/1

R1(config-if)#ip address 192.168.2.1 255.255.255.0

R1(config-if)#exit

R1(config)#router rip

R1(config-router)#network 192.168.1.0 0.0.0.255 //将和R2连接的端口加入rip协议中

R1(config-router)#network 192.168.2.0 0.0.0.255//将和PC1连接的端口加入rip协议中R

R1(config-router)#exit

R1(config)#

 

R2具体配置:

R2(config)#interface fei_1/1

R2(config-if)#ip address 192.168.1.2 255.255.255.0

R2(config-if)#exit

R2(config)#interface fei_0/1

R2(config-if)#ip address 192.168.3.1 255.255.255.0

R2(config-if)#exit

R2(config)#router rip

R2(config-router)#network 192.168.1.0 0.0.0.255 //将和R1连接的端口加入rip协议中

R2(config-router)#network 192.168.3.0 0.0.0.255//将和PC2连接的端口加入rip协议中

R2(config-router)#exit

R2(config)#

 

 

 

实验结果验证:

R1:show ip route

 

IPv4 Routing Table:

Dest        MASK        GW        Interface     Owner   pri     metric

192.168.1.0  255.255.255.0  192.168.1.1   fei_1/1     direct     0       0

192.168.1.1  255.255.255.255 192.168.1.1   fei_1/1     address    0       0

192.168.2.0  255.255.255.0  192.168.2.1    fei_0/1     direct     0       0

192.168.2.1  255.255.255.255 192.168.2.1    fei_0/1    address    0       0

192.168.3.0  255.255.255.0 192.168.1.2    fei_1/1       rip      120      2

 

测试网络互通性,应该是全网互通的。如果不是,请检查您的配置是否与上面的一致。现在我们可以看看RIP是怎样发现路由的,在特权模式下打开RIP协议调试开关,有如下信息在路由器之间传递,它们完成了路由的交换,并形成新的路由。

 

R1#debug ip rip all

 

00:19:36:RIP:building update entries

192.168.2.0/24 via 0.0.0.0,metric 1,tag 0

00:19:36:RIP:Update contains 1 routers

00:19:36:RIP:sending v2 periodic update to 224.0.0.9 via fei_1/1(192.168.1.1)

192.168.1.0/24 via 0.0.0.0,metric 1,tag 0

192.168.3.0/24 via 0.0.0.0,metric 2,tag 0

 

从上面的信息可以看到RIP协议版本为vision 2,这是中兴1800路由器的默认版本。水平分割默认是打开的。关闭水平分割后,可以查看和上面debug信息有何不同。

 

R1(config-if)#no ip split-horizon

R1#debug ip rip all

 

00:35:07:RIP:building update entries

192.168.2.0/24 via 0.0.0.0,metric 1,tag 0

192.168.3.0/24 via 0.0.0.0,metric 3,tag 0

00:35:07:RIP:Update contains 2 routes

00:35:07:Rip:sending v2 periodic update to 224.0.0.9 via fei_1/1(192.168.1.1)

192.168.1.0/24 via 0.0.0.0,metric 1,tag 0

192.168.3.0/24 via 0.0.0.0,metric 2,tag 0

00:35:07:RIP:Update contains 2 routes

00:35:07:RIP:sending v2 periodic update to 224.0.0.9 via fei_0/1(192.168.2.1)

 

在将R1R2PC互连得地址改为192.168.2.1/25192.168.2.129/25后,关掉自动聚合功能。观察关掉自动汇聚前后路由表的变化。

R1(config)#interface fei_0/1

R1(config-if)#ip address 192.168.2.1 255.255.255.128

R1(config-if)#exit

R1(config)#router rip

R1(config-router)#no auto-summary  //关闭自动汇总

R1#show ip router   //关闭前

 

IPv4 Routing Table:

Dest        MASK      GW        Interface       Owner   pri     metric

3.3.3.3  255.255.255.255  3.3.3.3    loopback1      address   0       0

192.168.1.0 255.255.255.0 192.168.1.1   fei_1/1       direct    0       0

192.168.1.1 255.255.255.255 192.168.1.1  fei_1/1      address   0       0

192.168.2.0 255.255.255.0 192.168.2.1   fei_0/1       direct    0       0

192.168.2.1 255.255.255.255 192.168.2.1  fei_0/1      address   0       0

 

R1#show ip router   //关闭后

 

IPv4 Routing Table:

Dest        MASK     GW      Interface      Owner   pri     metric

3.3.3.3   255.255.255.255  3.3.3.3    loopbac    address   0       0

192.168.1.0255.255.255.0 192.168.1.1   fei_1/1     direct    0       0

192.168.1.1 255.255.255.255 192.168.1.1  fei_1/1     address   0       0

192.168.2.0 255.255.255.0 192.168.1.2   fei_1/1       rip     0       0

192.168.2.0 255.255.255.128 192.168.2.1  fei_0/1    direct     0      0

192.168.2.1 255.255.255.255 192.168.2.1   fei_0     address   0       0

 

然后改变协议版本R1(config-router)#version 1并使之生效,并在关闭和启动自动聚合功能下显示路由表信息会发现都没有动态路由产生,知道为什么吗?因为version 1不支可持变长子网掩码,而192.168.2.1192.168.2.129属于C类地址,自然掩码为24位,属于同一网段的地址。大家可以自己做实验试一试。

 

实验结论:

对接设备的RIP版本要一致。多网段时注意自动汇聚功能。

 

 

4.9  OSPF单区域操作配置

 

使用CCS2000客户端将1#5#中任意2空闲的1800加入到队列中,连接设备串口。分别命名为R1R2,用交叉网线连接两台路由器快速以太网口。任意2PC编号PC1PC2PC1连接R1的快速以太网口,PC2连接R2的快速以太网口。具体实验拓扑图如下:

 

R1具体配置:

R1(config)#interface loopback1           //环回地址

R1(config-if)#ip address 10.1.1.1 255.255.255.255

R1(config-if)#exit

R1(config)#interface fei_1/1

R1(config-if)#ip address 192.168.1.1 255.255.255.0

R1(config-if)#exit

R1(config)#interface fei_0/1

R1(config-if)#ip address 192.168.2.1 255.255.255.0

R1(config-if)#exit

R1(config)#router ospf 10            //进入ospf路由配置模式,进程号为10

R1(config-router)#router-id 10.1.1.1   //loopback1配置为ospfrouter-id

R1(config-router)#network 192.168.1.0 0.0.0.255 area 0 //192.168.1.0/24网段加入ospf骨干区域area0

 

R1具体配置:

R1(config)#interface loopback1

R1(config-if)#ip address 10.1.2.1 255.255.255.255

R1(config-if)#exit

R1(config)#interface fei_1/1

R1(config-if)#ip address 192.168.1.2 255.255.255.0

R1(config-if)#exit

R1(config)#interface fei_0/1

R1(config-if)#ip address 192.168.3.1 255.255.255.0

R1(config-if)#exit

R1(config)#router ospf 10          

R1(config-router)#router-id 10.1.2.1 

R1(config-router)#network 192.168.1.0 0.0.0.255 area 0

 

实验结果验证:

R1#show ip ospf neighbor        //查看ospf邻居关系的建立情况

 

OSPF Router with ID(10.1.1.1)(Process ID 100)

Neighbor 10.1.2.1

In the area 0.0.0.0

Via interface fei_1/1 192.168.1.2

Neighbor is DR

State FULL,priority 1,Cost 1

Queue count:Retransmit 0,DD 0,LS Req 0

Dead time:00:00:37

In Full State for 00:00:35    //FULL状态表示建立成功

 

注:如果一台路由器没有手工配置router ID,则系统会从当前接口的IP地址中自动选一个。选择的原则如下:如果路由器配置了loopback接口,则优选loopback接口;如果没有loopback接口,则从已经UP的物理接口中选择接口IP地址最小的一个。对于该原则,大家可以自己在路由器上验证一下。由于自动选举的Router ID会随着IP地址的变化而改变,这样会干扰协议的正常运行。所以强烈建议:手工指定Router ID

 

R1#show ip route

 

IPv4 Routing Table:

Dest       MASK        GW      Interface       Owner   pri     metric

192.168.1.0  255.255.255.0 192.168.1.1  fei_1/1      direct    0        0

192.168.1.1 255.255.255.255 192.168.1.1 fei_1/1       address   0       0

192.168.2.0  255.255.255.0 192.168.2.1  fei_0/1      direct    0        0

192.168.2.1 255.255.255.255 192.168.2.1  fei_0/1     address   0        0

192.168.3.0 255.255.255.0  192.168.1.2  fei_1/1      ospf     110      20

 

实验结论:

    R1R2建立ospf邻居,能够互相学习到对方发布到同一区域的路由。

 

 

4.10  OSPF多区域操作配置

 

使用CCS2000客户端将1#5#中任意2空闲的1800加入到队列中,连接设备串口。分别命名为R1R2,用交叉网线连接两台路由器快速以太网口。任意2PC编号PC1PC2PC1连接R1的快速以太网口,PC2连接R2的快速以太网口。具体实验拓扑图如下:

 

R1具体配置:

R1(config)#interface loopback1

R1(config-if)#ip address 10.1.1.1 255.255.255.255

R1(config-if)#exit

R1(config)#interface fei_1/1

R1(config-if)#ip address 192.168.1.1 255.255.255.0

R1(config-if)#exit

R1(config)#interface fei_0/1

R1(config-if)#ip address 192.168.2.1 255.255.255.0

R1(config-if)#exit

R1(config)#router ospf 10

R1(config-router)#router-id 10.1.1.1

R1(config-router)#network 192.168.1.0 0.0.0.255 area 0

R1(config-router)#network 192.168.2.0 0.0.0.255 area 20

 

R2具体配置:

R2(config)#interface loopback1

R2(config-if)#ip address 10.1.2.1 255.255.255.255

R2(config-if)#exit

R2(config)#interface fei_1/1

R2(config-if)#ip address 192.168.1.2 255.255.255.0

R2(config-if)#exit

R2(config)#interface fei_0/1

R2(config-if)#ip address 192.168.3.1 255.255.255.0

R2(config-if)#exit

R2(config)#router ospf 10

R2(config-router)#router-id 10.1.1.1

R2(config-router)#network 192.168.1.0 0.0.0.255 area 0

R2(config-router)#network 192.168.3.0 0.0.0.255 area 20

 

实验结果验证:

R1#show ip route

 

IPv4 Routing Table:

Dest         MASK        GW      Interface       Owner   pri    metric

192.168.1.0  255.255.255.0   192.168.1.1   fei_1/1     direct     0       0

192.168.1.1  255.255.255.255 192.168.1.1   fei_1/1    address    0      0

192.168.2.0  255.255.255.0  192.168.2.1  fei_0/1      direct     0       0

192.168.2.1  255.255.255.255 192.168.2.1   fei_0/1     address    0       0

192.168.3.0  255.255.255.0  192.168.1.2  fei_1/1       ospf     110     20

 

实验结论:

    R1能够正确的跨域学习到R2发布的路由。

  • 1
    点赞
  • 6
    收藏
    觉得还不错? 一键收藏
  • 0
    评论
评论
添加红包

请填写红包祝福语或标题

红包个数最小为10个

红包金额最低5元

当前余额3.43前往充值 >
需支付:10.00
成就一亿技术人!
领取后你会自动成为博主和红包主的粉丝 规则
hope_wisdom
发出的红包
实付
使用余额支付
点击重新获取
扫码支付
钱包余额 0

抵扣说明:

1.余额是钱包充值的虚拟货币,按照1:1的比例进行支付金额的抵扣。
2.余额无法直接购买下载,可以购买VIP、付费专栏及课程。

余额充值