T2080RDB-PC uboot 引导Linux 内核启动
3162412793@qq.com
技术交流QQ群： 691976956
U-Boot 2016.012.0+ga9b437f (May 15 2016- 01:38:26 +0800)
CPU0: T2080E, Version: 1.1,(0x85380011)
Core: e6500, Version: 2.0,(0x80400120)
Clock Configuration:
CPU0:1799.820 MHz, CPU1:1799.820 MHz, CPU2:1799.820 MHz, CPU3:1799.820 MHz,
CCB:599.940 MHz,
DDR:933.310 MHz (1866.620 MT/s data rate) (Asynchronous), IFC:149.985 MHz
FMAN1: 699.930 MHz
QMAN: 299.970 MHz
PME: 599.940 MHz
L1: D-cache 32 KiB enabled
I-cache 32 KiB enabled
Reset Configuration Word (RCW):
00000000: 1207001b 15000000 00000000 00000000
00000010: 66150002 00000000 ec027000 c1000000
00000020: 00800000 00000000 00000000 000307fc
00000030: 00000000 00000000 00000000 00000004
I2C: ready
Board: T2080RDB, Board rev: 0x01 CPLDver: 0x06, boot from NOR vBank0
SERDES Reference Clocks:
SD1_CLK1=156.25MHZ, SD1_CLK2=100.00MHZ
SD2_CLK1=100.00MHZ, SD2_CLK2=100.00MHZ
SPI: ready
DRAM: Initializing....using SPD
Detected UDIMM D3XP56082XL10AA 2GiB left unmapped
4 GiB (DDR3, 64-bit, CL=13, ECC on)
DDRChip-Select Interleaving Mode: CS0+CS1
VID: Could not find voltage regulator onI2C.
Warning: Adjusting core voltage failed.
Flash: 128 MiB
L2: 2 MiB enabled
Corenet Platform Cache: 512 KiB enabled
Using SERDES1 Protocol: 102 (0x66)
Using SERDES2 Protocol: 21 (0x15)
SEC0: RNG instantiated
NAND: 512 MiB
MMC: FSL_SDHC: 0
EEPROM: Invalid ID (ff ff ff ff)
PCIe1: Endpoint, undetermined, regs @ 0xfe240000
PCIe1: Bus 00 - 00
PCIe2: Root Complex, x2 gen2, regs @ 0xfe250000
02:00.0 -1957:0808 - Processor
PCIe2: Bus 01 - 02
PCIe3: disabled
PCIe4: Root Complex, no link, regs @ 0xfe270000
PCIe4: Bus 03 - 03
In: serial
Out: serial
Err: serial
Net: Fman1: Uploading microcodeversion 106.4.18
FM1@DTSEC3 [PRIME], FM1@DTSEC4,FM1@TGEC1, FM1@TGEC2, FM1@TGEC3, FM1@TGEC4
Hit any key to stop autoboot: 0
WARNING: adjusting available memory to30000000
## Booting kernel from Legacy Image ate8020000 ...
Image Name: Linux-4.1.8-rt8+gbd51baf
Image Type: PowerPCLinux Kernel Image (gzip compressed)
Data Size: 5099857 Bytes = 4.9 MiB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
## Loading init Ramdisk from LegacyImage at e9300000 ...
Image Name: fsl-image-mfgtool-t2080rdb-20160
Image Type: PowerPCLinux RAMDisk Image (gzip compressed)
Data Size: 8398591Bytes = 8 MiB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
## Flattened Device Tree blob ate8800000
Booting using the fdt blobat 0xe8800000
Uncompressing Kernel Image... OK
Loading Ramdisk to2f7fd000, end 2ffff6ff ... OK
Loading Device Tree to03fe3000, end 03fff2c0 ... OK
Reserved memory: initialized nodebman-fbpr, compatible id fsl,bman-fbpr
Reserved memory: initialized nodeqman-fqd, compatible id fsl,qman-fqd
Reserved memory: initialized nodeqman-pfdr, compatible id fsl,qman-pfdr
Reserved memory: initialized nodepme-pdsr, compatible id fsl,pme-pdsr
Reserved memory: initialized nodepme-sre, compatible id fsl,pme-sre
Using CoreNet Generic machinedescription
MMU: Supported page sizes
4 KB as direct
2048 KBas direct & indirect
4096 KBas direct
16384 KB asdirect
65536 KB asdirect
262144 KB as direct
1048576 KB as direct
MMU: Book3E HW tablewalk enabled
Found initrd at0xc00000002f7fd000:0xc00000002ffff6ff
bootconsole [udbg0] enabled
CPU maps initialized for 2 threads percore
Starting Linux PPC64 #1 SMP Sun May 1501:39:21 CST 2016
-----------------------------------------------------
ppc64_pft_size = 0x0
phys_mem_size = 0x100000000
dcache_line_size = 0x40
icache_line_size = 0x40
cpu_features =0x00180480581802c8
possible = 0x00180480581802c8
always = 0x00180400581802c0
cpu_user_features = 0xdc008000 0x08000000
mmu_features =0x000a0010
firmware_features = 0x0000000000000000
-----------------------------------------------------
<- setup_system()
Linux version 4.1.8-rt8+gbd51baf(jenkins@mercury) (gcc version 4.9.2 (GCC) ) #1 SMP Sun May 15 01:39:21 CST2016
CoreNet Generic board
Zone ranges:
DMA [mem 0x0000000000000000-0x000000007fffffff]
DMA32 empty
Normal [mem0x0000000080000000-0x00000000ffffffff]
Movable zone start for each node
Early memory node ranges
node 0: [mem0x0000000000000000-0x00000000ffffffff]
Initmem setup node 0 [mem0x0000000000000000-0x00000000ffffffff]
MMU: Allocated 2112 bytes of contextmaps for 255 contexts
PERCPU: Embedded 17 pages/cpu@c0000000ffe00000 s28824 r0 d40808 u131072
Built 1 zonelists in Zone order,mobility grouping on. Total pages: 1034240
Kernel command line: root=/dev/ram rwconsole=ttyS0,115200
log_buf_len individual max cpucontribution: 4096 bytes
log_buf_len total cpu_extra contributions:28672 bytes
log_buf_len min size: 16384 bytes
log_buf_len: 65536 bytes
early log buf free: 12040(73%)
PID hash table entries: 4096 (order: 3,32768 bytes)
Dentry cache hash table entries: 524288(order: 10, 4194304 bytes)
Inode-cache hash table entries: 262144(order: 9, 2097152 bytes)
Sorting __ex_table...
Memory: 3957696K/4194304K available(7856K kernel code, 1136K rwdata, 2972K rodata, 364K init, 764K bss, 236608Kreserved, 0K cma-reserved)
Hierarchical RCU implementation.
RCU debugfs-based tracing is enabled.
CONFIG_RCU_FANOUT set to non-default value of 32
Additional per-CPU info printed with stalls.
RCU restricting CPUs from NR_CPUS=24 to nr_cpu_ids=8.
RCU: Adjusting geometry forrcu_fanout_leaf=16, nr_cpu_ids=8
NR_IRQS:512 nr_irqs:512 16
mpic: Setting up MPIC "OpenPIC " version 1.2 at ffe040000, max 8 CPUs
mpic: ISU size: 512, shift: 9, mask: 1ff
mpic: Initializing for 512 sources
clocksource timebase: mask:0xffffffffffffffff max_cycles: 0x8a5d528ca, max_idle_ns: 440795203517 ns
clocksource: timebase mult[1aab5972]shift[24] registered
Console: colour dummy device 80x25
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 8192(order: 4, 65536 bytes)
Mountpoint-cache hash table entries:8192 (order: 4, 65536 bytes)
e6500 family performance monitorhardware support registered
Brought up 8 CPUs
devtmpfs: initialized
clocksource jiffies: mask: 0xffffffffmax_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
xor: measuring software checksum speed
8regs : 3570.000 MB/sec
8regs_prefetch: 3158.000 MB/sec
32regs : 3012.000 MB/sec
32regs_prefetch: 2659.000 MB/sec
altivec : 5679.000 MB/sec
xor: using function: altivec (5679.000MB/sec)
NET: Registered protocol family 16
Bman ver:0a02,02,01
qman-fqd addr 0xff000000 size 0x800000
qman-pfdr addr 0xfc000000 size 0x2000000
Qman ver:0a01,03,01,02
Can't find hose for PCI bus 0!
EDAC PCI0: Giving out device to moduleMPC85xx_edac controller mpc85xx_pci_err: DEV ffe240000.pcie (INTERRUPT)
MPC85xx_edac acquired irq 20 for PCI Err
MPC85xx_edac PCI err registered
platform ffe240000.pcie:pcie@0: Invalidsize 0xfffff9 for dma-range
Found FSL PCI host bridge at0x0000000ffe250000. Firmware bus number: 0->1
PCI host bridge /pcie@ffe250000 ranges:
MEM0x0000000c20000000..0x0000000c2fffffff -> 0x00000000e0000000
IO0x0000000ff8010000..0x0000000ff801ffff -> 0x0000000000000000
/pcie@ffe250000: PCICSRBAR @ 0xff000007
setup_pci_atmu: end of DRAM 100000000
/pcie@ffe250000: Setup 64-bit PCI DMAwindow
/pcie@ffe250000: WARNING: Outboundwindow cfg leaves gaps in memory map. Adjusting the memory map could reduceunnecessary bounce buffering.
/pcie@ffe250000: DMA window size is0xe0000000
EDAC PCI1: Giving out device to moduleMPC85xx_edac controller mpc85xx_pci_err: DEV ffe250000.pcie (INTERRUPT)
MPC85xx_edac acquired irq 21 for PCI Err
MPC85xx_edac PCI err registered
platform ffe250000.pcie:pcie@0: Invalidsize 0xfffff9 for dma-range
Found FSL PCI host bridge at0x0000000ffe270000. Firmware bus number: 0->0
PCI host bridge /pcie@ffe270000 ranges:
MEM0x0000000c40000000..0x0000000c4fffffff -> 0x00000000e0000000
IO0x0000000ff8030000..0x0000000ff803ffff -> 0x0000000000000000
/pcie@ffe270000: PCICSRBAR @ 0xff000007
setup_pci_atmu: end of DRAM 100000000
/pcie@ffe270000: Setup 64-bit PCI DMAwindow
/pcie@ffe270000: WARNING: Outboundwindow cfg leaves gaps in memory map. Adjusting the memory map could reduceunnecessary bounce buffering.
/pcie@ffe270000: DMA window size is0xe0000000
EDAC PCI2: Giving out device to moduleMPC85xx_edac controller mpc85xx_pci_err: DEV ffe270000.pcie (INTERRUPT)
MPC85xx_edac acquired irq 23 for PCI Err
MPC85xx_edac PCI err registered
platform ffe270000.pcie:pcie@0: Invalidsize 0xfffff9 for dma-range
software IO TLB [mem0xf2e00000-0xf6e00000] (64MB) mapped at [c0000000f2e00000-c0000000f6dfffff]
PCI: Probing PCI hardware
fsl-pci ffe250000.pcie: PCI host bridgeto bus 0001:00
pci_bus 0001:00: root bus resource[io 0x10000-0x1ffff] (bus address [0x0000-0xffff])
pci_bus 0001:00: root bus resource [mem0xc20000000-0xc2fffffff] (bus address [0xe0000000-0xefffffff])
pci_bus 0001:00: root bus resource [bus00-01]
pci 0001:00:00.0: [Firmware Bug]: reg0x10: invalid BAR (can't size)
pci 0001:00:00.0: PCI bridge to [bus01-ff]
fsl-pci ffe270000.pcie: PCI host bridgeto bus 0002:00
pci_bus 0002:00: root bus resource[io 0x21000-0x30fff] (bus address [0x0000-0xffff])
pci_bus 0002:00: root bus resource [mem0xc40000000-0xc4fffffff] (bus address [0xe0000000-0xefffffff])
pci_bus 0002:00: root bus resource [bus00]
pci 0002:00:00.0: [Firmware Bug]: reg0x10: invalid BAR (can't size)
pci 0002:00:00.0: bridge configurationinvalid ([bus 00-00]), reconfiguring
pci 0002:00:00.0: PCI bridge to [bus01-ff]
PCI: Cannot allocate resource region 6of device 0001:00:00.0, will remap
pci 0001:00:00.0: BAR 6: no space for[mem size 0x01000000 pref]
pci 0001:00:00.0: BAR 6: failed toassign [mem size 0x01000000 pref]
pci 0001:00:00.0: PCI bridge to [bus 01]
pci 0001:00:00.0: bridgewindow [io 0x10000-0x1ffff]
pci 0001:00:00.0: bridgewindow [mem 0xc20000000-0xc2fffffff]
pci 0002:00:00.0: BAR 6: no space for[mem size 0x01000000 pref]
pci 0002:00:00.0: BAR 6: failed toassign [mem size 0x01000000 pref]
pci 0002:00:00.0: PCI bridge to [bus 01]
pci 0002:00:00.0: bridgewindow [io 0x21000-0x30fff]
pci 0002:00:00.0: bridgewindow [mem 0xc40000000-0xc4fffffff]
raid6: altivecx1 gen() 1111 MB/s
raid6: altivecx2 gen() 1850 MB/s
raid6: altivecx4 gen() 3049 MB/s
raid6: altivecx8 gen() 2969 MB/s
raid6: int64x1 gen() 519 MB/s
raid6: int64x1 xor() 775 MB/s
raid6: int64x2 gen() 873 MB/s
raid6: int64x2 xor() 927 MB/s
raid6: int64x4 gen() 1335MB/s
raid6: int64x4 xor() 1024MB/s
raid6: int64x8 gen() 1148MB/s
raid6: int64x8 xor() 831 MB/s
raid6: using algorithm altivecx4 gen()3049 MB/s
raid6: using intx1 recovery algorithm
vgaarb: loaded
SCSI subsystem initialized
usbcore: registered new interface driverusbfs
usbcore: registered new interface driverhub
usbcore: registered new device driverusb
pps_core: LinuxPPS API ver. 1 registered
pps_core: Software ver. 5.3.6 -Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
PTP clock support registered
EDAC MC: Ver: 3.0.0
bman-fbpr addr 0xfe000000 size 0x1000000
Bman err interrupt handler present
Bman portal initialised, cpu 0
Bman portal initialised, cpu 1
Bman portal initialised, cpu 2
Bman portal initialised, cpu 3
Bman portal initialised, cpu 4
Bman portal initialised, cpu 5
Bman portal initialised, cpu 6
Bman portal initialised, cpu 7
Bman portals initialised
Qman err interrupt handler present
QMan: Allocated lookup table at8000000000002000, entry count 131073
Qman portal initialised, cpu 0
Qman portal initialised, cpu 1
Qman portal initialised, cpu 2
Qman portal initialised, cpu 3
Qman portal initialised, cpu 4
Qman portal initialised, cpu 5
Qman portal initialised, cpu 6
Qman portal initialised, cpu 7
Qman portals initialised
Bman: BPID allocator includes range32:32
Qman: FQID allocator includes range256:512
Qman: FQID allocator includes range32768:32768
Qman: CGRID allocator includes range0:256
Qman: pool channel allocator includesrange 1025:15
No USDPAA memory, no 'fsl,usdpaa-mem' indevice-tree
fsl-ifc ffe124000.localbus: FreescaleIntegrated Flash Controller
fsl-ifc ffe124000.localbus: IFC version1.3, 8 banks
Switched to clocksource timebase
NET: Registered protocol family 2
TCP established hash table entries:32768 (order: 6, 262144 bytes)
TCP bind hash table entries: 32768(order: 7, 524288 bytes)
TCP: Hash tables configured (established32768 bind 32768)
UDP hash table entries: 2048 (order: 4,65536 bytes)
UDP-Lite hash table entries: 2048(order: 4, 65536 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX sockettransport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchanneltransport module.
Trying to unpack rootfs image asinitramfs...
rootfs image is not initramfs (no cpiomagic); looks like an initrd
Freeing initrd memory: 8200K (c00000002f7fd000- c00000002ffff000)
futex hash table entries: 2048 (order:5, 131072 bytes)
audit: initializing netlink subsys(disabled)
audit: type=2000 audit(1.756:1):initialized
HugeTLB registered 4 MB page size,pre-allocated 0 pages
HugeTLB registered 16 MB page size,pre-allocated 0 pages
HugeTLB registered 64 MB page size,pre-allocated 0 pages
HugeTLB registered 256 MB page size,pre-allocated 0 pages
HugeTLB registered 1 GB page size,pre-allocated 0 pages
NFS: Registering the id_resolver keytype
Key type id_resolver registered
Key type id_legacy registered
ntfs: driver 2.1.32 [Flags: R/O].
jffs2: version 2.2. (NAND) © 2001-2006Red Hat, Inc.
async_tx: api initialized (async)
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
Serial: 8250/16550 driver, 4 ports, IRQsharing enabled
console [ttyS0] disabled
serial8250.0: ttyS0 at MMIO 0xffe11c500(irq = 36, base_baud = 18748125) is a 16550A
console [ttyS0] enabled
console [ttyS0] enabled
bootconsole [udbg0] disabled
bootconsole [udbg0] disabled
serial8250.0: ttyS1 at MMIO 0xffe11c600(irq = 36, base_baud = 18748125) is a 16550A
serial8250.0: ttyS2 at MMIO 0xffe11d500(irq = 37, base_baud = 18748125) is a 16550A
serial8250.0: ttyS3 at MMIO 0xffe11d600(irq = 37, base_baud = 18748125) is a 16550A
ePAPR hypervisor byte channel driver
brd: module loaded
loop: module loaded
st: Version 20101219, fixed bufsize32768, s/g segs 256
fsl-sata ffe220000.sata: Sata FSLPlatform/CSB Driver init
scsi host0: sata_fsl
ata1: SATA max UDMA/133 irq 68
fsl-sata ffe221000.sata: Sata FSLPlatform/CSB Driver init
scsi host1: sata_fsl
ata2: SATA max UDMA/133 irq 69
fe8000000.nor: Found 1 x16 devices at0x0 in 16-bit bank. Manufacturer ID 0x000089 Chip ID 0x00227e
Amd/Fujitsu Extended Query Table at0x0040
Amd/Fujitsu Extended Queryversion 1.3.
number of CFI chips: 1
nand: device found, Manufacturer ID:0x2c, Chip ID: 0xac
nand: Micron MT29F4G08ABBDAH4
nand: 512 MiB, SLC, erase size: 128 KiB,page size: 2048, OOB size: 64
Bad block table found at page 262080,version 0x01
Bad block table found at page 262016,version 0x01
fsl,ifc-nand fff800000.nand: IFC NANDdevice at 0xfff800000, bank 1
fsl_espi ffe110000.spi: cs=0,init_csmode=0x100008
m25p80 spi32766.0: found n25q512ax3,expected n25q512a
m25p80 spi32766.0: n25q512ax3 (65536Kbytes)
fsl_espi ffe110000.spi: at0x80000800809ae000 (irq = 53)
libphy: Fixed MDIO Bus: probed
libphy: Freescale XGMAC MDIO Bus: probed
libphy: Freescale XGMAC MDIO Bus: probed
libphy: Freescale XGMAC MDIO Bus: probed
libphy: Freescale XGMAC MDIO Bus: probed
libphy: Freescale XGMAC MDIO Bus: probed
libphy: Freescale XGMAC MDIO Bus: probed
libphy: Freescale XGMAC MDIO Bus: probed
libphy: Freescale XGMAC MDIO Bus: probed
libphy: Freescale XGMAC MDIO Bus: probed
libphy: Freescale XGMAC MDIO Bus: probed
cpu0/24: > WARNING (FM) [CPU00,/home/jenkins/ci/sdk/master/t2080rdb/sources/linux/drivers/net/ethernet/freescale/sdk_fman/Peripherals/FM/fm.c:3547FM_Init]:
cpu0/24: Hack: No FM reset!
cpu0/24:
Freescale FM module, FMD API version21.1.0
Freescale FM Ports module
fsl_mac: fsl_mac: FSL FMan MAC API baseddriver
fsl_mac ffe4e0000.ethernet: FMan MEMAC
fsl_mac ffe4e0000.ethernet: FMan MACaddress: 00:04:9f:04:74:2e
fsl_mac ffe4e2000.ethernet: FMan MEMAC
fsl_mac ffe4e2000.ethernet: FMan MACaddress: 00:04:9f:04:74:2f
fsl_mac ffe4e4000.ethernet: FMan MEMAC
fsl_mac ffe4e4000.ethernet: FMan MACaddress: 00:04:9f:04:74:30
fsl_mac ffe4e6000.ethernet: FMan MEMAC
fsl_mac ffe4e6000.ethernet: FMan MACaddress: 00:04:9f:04:74:31
fsl_mac ffe4f0000.ethernet: FMan MEMAC
fsl_mac ffe4f0000.ethernet: FMan MACaddress: 00:04:9f:04:74:32
fsl_mac ffe4f2000.ethernet: FMan MEMAC
fsl_mac ffe4f2000.ethernet: FMan MACaddress: 00:04:9f:04:74:33
fsl_dpa: FSL DPAA Ethernet driver
fsl_dpa: fsl_dpa: Probed interface eth0
fsl_dpa: fsl_dpa: Probed interface eth1
fsl_dpa: fsl_dpa: Probed interface eth2
fsl_dpa: fsl_dpa: Probed interface eth3
fsl_dpa: fsl_dpa: Probed interface eth4
fsl_dpa: fsl_dpa: Probed interface eth5
fsl_advanced: FSL DPAA Advanced drivers:
fsl_proxy: FSL DPAA Proxy initializationdriver
fsl_dpa_shared: FSL DPAA Shared Ethernetdriver
fsl_dpa_macless: FSL DPAA MAClessEthernet driver
fsl_oh: FSL FMan Offline Parsing portdriver
e1000e: Intel(R) PRO/1000 Network Driver- 2.3.2-k
e1000e: Copyright(c) 1999 - 2014 IntelCorporation.
fsl-of-dma ffe100300.dma: dma channeldma-uio0-0 initialized
fsl-of-dma ffe100300.dma: dma channeldma-uio0-1 initialized
fsl-of-dma ffe100300.dma: dma channeldma-uio0-2 initialized
fsl-of-dma ffe100300.dma: dma channeldma-uio0-3 initialized
fsl-of-dma ffe100300.dma: dma channeldma-uio0-4 initialized
fsl-of-dma ffe100300.dma: dma channeldma-uio0-5 initialized
fsl-of-dma ffe100300.dma: dma channeldma-uio0-6 initialized
fsl-of-dma ffe100300.dma: dma channeldma-uio0-7 initialized
fsl-of-dma ffe101300.dma: dma channeldma-uio1-0 initialized
fsl-of-dma ffe101300.dma: dma channeldma-uio1-1 initialized
fsl-of-dma ffe101300.dma: dma channeldma-uio1-2 initialized
fsl-of-dma ffe101300.dma: dma channeldma-uio1-3 initialized
fsl-of-dma ffe101300.dma: dma channeldma-uio1-4 initialized
fsl-of-dma ffe101300.dma: dma channeldma-uio1-5 initialized
fsl-of-dma ffe101300.dma: dma channeldma-uio1-6 initialized
fsl-of-dma ffe101300.dma: dma channeldma-uio1-7 initialized
fsl-of-dma ffe102300.dma: dma channeldma-uio2-0 initialized
fsl-of-dma ffe102300.dma: dma channeldma-uio2-1 initialized
fsl-of-dma ffe102300.dma: dma channeldma-uio2-2 initialized
fsl-of-dma ffe102300.dma: dma channeldma-uio2-3 initialized
fsl-of-dma ffe102300.dma: dma channeldma-uio2-4 initialized
fsl-of-dma ffe102300.dma: dma channeldma-uio2-5 initialized
fsl-of-dma ffe102300.dma: dma channeldma-uio2-6 initialized
fsl-of-dma ffe102300.dma: dma channeldma-uio2-7 initialized
ehci_hcd: USB 2.0 'Enhanced' HostController (EHCI) Driver
ehci-pci: EHCI PCI platform driver
fsl-ehci fsl-ehci.0: Freescale On-ChipEHCI Host Controller
fsl-ehci fsl-ehci.0: new USB busregistered, assigned bus number 1
fsl-ehci fsl-ehci.0: irq 44, io mem0xffe210000
fsl-ehci fsl-ehci.0: USB 2.0 started,EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
fsl-ehci fsl-ehci.1: Freescale On-ChipEHCI Host Controller
fsl-ehci fsl-ehci.1: new USB busregistered, assigned bus number 2
ata1: No Device OR PHYRDY change,Hstatus= 0xa0000000
ata1: SATA link down (SStatus 10SControl 300)
fsl-ehci fsl-ehci.1: irq 45, io mem0xffe211000
ata2: No Device OR PHYRDY change,Hstatus= 0xa0000000
ata2: SATA link down (SStatus 10SControl 300)
fsl-ehci fsl-ehci.1: USB 2.0 started, EHCI1.00
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
usbcore: registered new interface driverusb-storage
i2c /dev entries driver
mpc-i2c ffe118000.i2c: timeout 1000000us
rtc-ds1307 0-0068: rtc core: registeredds1339 as rtc0
mpc-i2c ffe118100.i2c: timeout 1000000us
mpc-i2c ffe119000.i2c: timeout 1000000us
mpc-i2c ffe119100.i2c: timeout 1000000us
i2c i2c-1: Added multiplexed i2c bus 4
i2c i2c-1: Added multiplexed i2c bus 5
i2c i2c-1: Added multiplexed i2c bus 6
i2c i2c-1: Added multiplexed i2c bus 7
pca954x 1-0077: registered 4 multiplexedbusses for I2C switch pca9546
md: raid6 personality registered forlevel 6
md: raid5 personality registered forlevel 5
md: raid4 personality registered forlevel 4
Freescale(R) MPC85xx EDAC driver, (C)2006 Montavista Software
EDAC MC0: Giving out device to moduleMPC85xx_edac controller mpc85xx_mc_err: DEV mpc85xx_mc_err (INTERRUPT)
MPC85xx_edac acquired irq 490 for MC
MPC85xx_edac MC err registered
sdhci: Secure Digital Host ControllerInterface driver
sdhci: Copyright(c) Pierre Ossman
sdhci-pltfm: SDHCI platform and OFdriver helper
sdhci-esdhc ffe114000.sdhc: No vmmcregulator found
sdhci-esdhc ffe114000.sdhc: No vqmmcregulator found
mmc0: SDHCI controller on ffe114000.sdhc[ffe114000.sdhc] using ADMA 64-bit
platform caam_qi.0: Linux CAAM Queue I/Fdriver initialised
caam ffe300000.crypto: Instantiated RNG4SH1
caam ffe300000.crypto: device ID =0x0a13020000000000 (Era 6)
caam ffe300000.crypto: job rings = 4, qi= 1
caam algorithms registered in /proc/crypto
platform caam_qi.0: fsl,sec-v5.2algorithms registered in /proc/crypto
caam_jr ffe301000.jr: registeringrng-caam
caam ffe300000.crypto: fsl,sec-v5.2algorithms registered in /proc/crypto
usbcore: registered new interface driverusbhid
usbhid: USB HID core driver
Freescale USDPAA process driver
fsl-usdpaa: no region found
Freescale USDPAA process IRQ driver
dce_sys_init done!
fsl-dce ffe312000.dce: Device/soc@ffe000000/dce@312000 initialized ver: 0x0af00101
fsl-pme ffe316000.pme: ver: 0x00100201
Freescale pme2 db driver
Freescale pme2 scan driver
fsl-pme2-scan: device pme_scanregistered
Freescale hypervisor management driver
fsl-hv: no hypervisor found
ipip: IPv4 over IPv4 tunneling driver
Initializing XFRM netlink socket
NET: Registered protocol family 10
sit: IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
NET: Registered protocol family 15
8021q: 802.1Q VLAN Support v1.8
Key type dns_resolver registered
fsl_generic: FSL DPAA Generic Ethernetdriver
rtc-ds1307 0-0068: setting system clockto 2016-05-14 17:50:59 UTC (1463248259)
md: Skipping autodetection of RAIDarrays. (raid=autodetect will force)
RAMDISK: gzip image found at block 0
VFS: Mounted root (ext2 filesystem) ondevice 1:0.
devtmpfs: mounted
Freeing unused kernel memory: 364K(c000000000a9a000 - c000000000af5000)
INIT: version 2.88 booting
Starting udev
udevd[1358]: starting version 182
fsl_dpa fsl,dpaa:ethernet@0 fm1-mac1:renamed from eth0
udevd[1365]: renamed network interfaceeth0 to fm1-mac1
fsl_dpa fsl,dpaa:ethernet@1 fm1-mac2:renamed from eth1
fsl_dpa fsl,dpaa:ethernet@2 fm1-mac3:renamed from eth2
udevd[1363]: renamed network interfaceeth1 to fm1-mac2
fsl_dpa fsl,dpaa:ethernet@3 fm1-mac4:renamed from eth3
udevd[1361]: renamed network interfaceeth2 to fm1-mac3
fsl_dpa fsl,dpaa:ethernet@9 fm1-mac10:renamed from eth5
udevd[1366]: renamed network interfaceeth3 to fm1-mac4
fsl_dpa fsl,dpaa:ethernet@8 fm1-mac9:renamed from eth4
udevd[1367]: renamed network interfaceeth5 to fm1-mac10
udevd[1364]: renamed network interfaceeth4 to fm1-mac9
bootlogd: cannot allocate pseudo tty: Nosuch file or directory
random: dd urandom read with 8 bits ofentropy available
Populating dev cache
Running postinst/etc/rpm-postinsts/100-sysvinit-inittab...
update-rc.d: /etc/init.d/run-postinstsexists during rc.d purge (continuing)
INIT: Entering runlevel: 5
Configuring network interfaces... done.
Starting OpenBSD Secure Shell server:sshd
generating ssh RSA key...
generating ssh ECDSA key...
generating ssh DSA key...
generating ssh ED25519 key...
done.
Starting syslogd/klogd: done
QorIQ SDK (FSL Reference Distro) 2.0t2080rdb /dev/ttyS0
t2080rdb login: root
t2080rdb~
1万+
被折叠的 条评论
为什么被折叠?
到【灌水乐园】发言
