所有盘都认到了，有个LUN少了一半路径，或者就差一个LUN没认到

以前都是通过把主机移出storage group，然后再移进来，做这个操作需要系统停机。通过与EMC交流，EMC称LUNZ的盘为鬼盘，这种盘在系统里看不再是数据盘，可以删除再重新认。

>#lsdev -Cc disk |grep LUNZ
hdisk4 Defined 05-08-01 EMC CLARiiON FCP LUNZ Disk
hdisk5 Defined 06-08-01 EMC CLARiiON FCP LUNZ Disk
hdisk66 Defined 05-08-01 EMC CLARiiON FCP LUNZ Disk
hdisk67 Defined 05-08-01 EMC CLARiiON FCP LUNZ Disk
hdisk68 Defined 05-08-01 EMC CLARiiON FCP LUNZ Disk
hdisk69 Defined 05-08-01 EMC CLARiiON FCP LUNZ Disk
hdisk70 Available 06-08-01 EMC CLARiiON FCP LUNZ Disk
hdisk71 Available 06-08-01 EMC CLARiiON FCP LUNZ Disk
hdisk72 Defined 06-08-01 EMC CLARiiON FCP LUNZ Disk
hdisk73 Defined 06-08-01 EMC CLARiiON FCP LUNZ Disk

powermt display dev=all

Pseudo name=hdiskpower40

CLARiiON ID=*********

Logical device ID=****** [LUN 4]

state=alive; policy=CLAROpt; priority=0; queued-IOs=1

Owner: default=SP A, current=SP A

==============================================================================

---------------- Host --------------- - Stor - -- I/O Path - -- Stats ---

### HW Path I/O Paths Interf. Mode State Q-IOs Errors

==============================================================================

0 fscsi0 hdisk194 SP B0 active alive 0 0

0 fscsi0 hdisk195 SP A0 active alive 1 0

这里正常要有四个盘，fscsi1认的盘不见了，其实这块物理盘在操作系统里认的是

hdisk70 hdisk71 hdisk194 hdisk195，但系统不再认为hdisk70 hdisk71是数据盘，无法合并路径，将鬼盘删除，重新cfgmgr即可。

[@more@]

The following is a Primus(R) eServer solution:
ID: emc111635
Domain: EMC1
Solution Class: 3.X Compatibility
Goal How to remove LUNZ devices
Fact Product: CLARiiON
Fact EMC SW: Navisphere CLI
Fact EMC SW: Navisphere
Fact OS: IBM AIX
Symptom Why do LUNZ devices appear on an AIX host even though storage is attached?
Symptom Unable to see one LUN from an AIX server
Symptom SC_DISK_ERR2 or SC_DISK_ERR4
Symptom LUNZ devices appear after running cfgmgr, but were not there previously.
Change The Array LUN Unit (ALU) associated with the Host LUN Unit (HLU) 0 was removed from the Storage Group.
Change CLARiiON LUNs attached to host.

Cause LUNZ devices are visible to a host, regardless of the operating system, when the Arraycomm Path setting is enabled for an HBA initiator record and that initiator does not see a physical LUN with an address of 0. Prior to seeing physical storage (i.e. adding a host to a storage group), every zoned IO path to a Clariion should see a LUNZ. It's purpose is for initial Navisphere Agent communication and registration with the Clariion array. When a LUN is added to a storage group (by default the first one added is given HLU 0) the LUNZ is no longer necessary because the agent will then communicate through the physical storage. If the LUN with address 0 is removed then the LUNZ devices will once again become visible provided that Arraycomm Path is enabled.
Fix

First verify you are experiencing the problem:

From the ·Enterprise Storage· window in Navisphere Manager:

1. Click the ·Hosts· tab.

2. Right-click the host in question and select ·Properties.·

3. Click the ·Storage· tab.

Note: You should not see a HLU 0 in the ·Host LUN ID· column.

Fix 1 · Using Navisphere Manager:

Run the following commands on the AIX host:

1. lsdev -Cc disk | grep LUNZ to get a list of the hdisk devices that are LUNZ devices.

2. rmdev -dl hdiskn for every LUNZ device, where n is the hdisk number of the LUNZ

Change Failover settings in Navisphere Manager:

3. Click ·Tools· => ·Failover Setup Wizard·

4. Select the appropriate options in the Wizard.

· FailoverMode = 1

· Arraycomm Path = Disabled

· Initiator Type = Clariion Open

· Unit Serial Number = Array

Run the following commands on the AIX host:

5. cfgmgr

6. lsdev -Cc disk | grep LUNZ and verify LUNZ devices are no longer visible.

Fix 2 · Using the navicli command set:

On the AIX host run the following:

1. lsdev -Cc disk | grep LUNZ to get a list of the hdisk devices that are LUNZ devices.

2. rmdev -dl hdiskn for every LUNZ device, where n is the hdisk number of the LUNZ

3. navicli -h storagegroup -sethost -host -arraycommpath 0

4. cfgmgr

5. lsdev -Cc disk | grep LUNZ to verify LUNZ devices are now gone.

Fix 3 · Creating a new LUN:

On the AIX host:

1. lsdev -Cc disk | grep LUNZ to get a list of the hdisk devices that are LUNZ devices.

2. rmdev -dl hdiskn for every LUNZ device, where n is the hdisk number of the LUNZ

From Navisphere Manager:

3. Bind a small LUN.

4. Add the LUN to the Storage Group in question.

5. Before applying the configuration scroll the "Selected LUNs" field to the right.

6. Change the "Host ID" field to 0 by clicking the blank space and choosing from the drop down menu.

7. Apply and OK

On the AIX host:

8. Run cfgmgr on the host.

9. Run lsdev -Cc disk | grep LUNZ to verify LUNZ devices are now gone
Note If the above procedures fail to rid the AIX host of LUNZ devices, verify you are not zoned to another CLARiiON array as this will also present LUNZ devices.

来自 “ ITPUB博客 ” ，链接：http://blog.itpub.net/668365/viewspace-1020234/，如需转载，请注明出处，否则将追究法律责任。

转载于:http://blog.itpub.net/668365/viewspace-1020234/