. IBM RS6000小型机机房要求:
1. 机房的卫生状况,要求清洁,键盘、显示器、机柜上没有灰尘。
2. 温度(摄氏 ℃)
10 ℃-40℃
湿度(%)
8% -80%
2. 设备故障灯分类:
主机故障灯
面板上不能有数字显示,如果有的话,说明系统有故障。
7133磁盘阵列故障灯
告警灯为黄色表示有故障
磁带机故障灯
告警灯为黄色说明有故障或磁带机太脏,须清洗。
3. 系统错误报告(Error Log)的检查:
硬件故障检测命令:# errpt -d H -T PERM
若有故障执行命令# errpt -a -d H -T PERM>/tmp/harderror.log保存,分析结果报告给客户
软件故障检测命令:# errpt -d S -T PERM
若有故障执行命令# errpt -a -d S -T PERM>/tmp/softerror.log保存,分析结果报告给客户
4. 有否发给root用户的错误报告(mail):
#mail
1. 观察所有未读消息,注意有关diagela的消息。
2. 常用命令:
h [] Display headings of group containing message
t [] Display messages in or current message.
n Display next message.
q Quit
3. 对发现的问题详细分析,结果报告给客户
5. 件系统的检查:
命令:
# df –k
%Used为文件系统的使用率。所有文件系统的使用率不能大于80%
6.磁带机清洁的检查:
命令:
#/usr/lpp/diagnostics/bin/utape -cd rmt0 –n
显示结果为磁带机使用的小时数,若大于72小时,则不论磁带机黄灯是否亮都应用清洁带清洗。
6. 信系统的检测:
1. 网卡的状态
命令:
#ifconfig –a
输出判断:
en0: flags=e080863
inet 192.9.200.2 netmask 0xffffff00 broadcast 192.9.200.255
en1: flags=e080863
inet 192.9.201.1 netmask 0xffffff00 broadcast 192.9.200.255
主备网卡的flag为UP属正常。同时检查ip地址和netmask是否正确。
2. 路由的检测
命令:
#lsattr –El inet0
authm 65536 Authentication Methods True
hostname h24 Host Name True
gateway Gateway True
route net,,0,172.16.23.81 Route True
bootup_option no Serial Optical Network Interface True
rout6 FDDI Network Interface True
3. 络的检测
命令:
#ping [ip address]
输出判断:
用ping命令对/etc/hosts文件中的IP地址进行操作,检测网络是否联通。
RAID 的Hotspare 属性是否打开
#smitty ssaraidà Change/Show Attributes of an SSA RAID Array
检查Enable Use of Hot Spares属性是否为YES
8.系统DUMP设置的检查
命令:
#sysdumdev –l
输出判断:
结果应为
primary /dev/hd6
secondary /dev/sysdumpnull
copy directory /var/adm/ras
forced copy flag TRUE
always allow dump FALSE
dump compression OFF
若不正确请用下列命令修改:
#sysdumdev –P –p /dev/hd6 –s /dev/sysdumpnull
9.HACMP 配置检测: Cluster Verification:
命令:
# /usr/sbin/cluster/diag/clconfig -v '-tr'
输出判断:
结果无Fail项输出。
10.系统硬件诊断:
命令顺序为:
1.#diag
2.Enter
3.Diagnostic Routines
4.System Verification
5.All Resources
6.F7
输出判断:
结果应为No trouble was found.
11.补丁程序(PTF)的检查
1. 系统维护补丁版本为ML09,检查命令为:
#instfix –i |grep ML
输出判断:
结果应为
输出判断:
结果应为
更改命令为:
输出判断:
结果应为
更改命令为:
输出判断:
结果应为
输出判断:
结果应为
更改命令为:
#smitty aio
输出判断:
结果应为
time(seconds) unlimited
file(blocks) 2097151
data(kbytes) 262144 //尤其是这项参数
stack(kbytes) 32768
memory(kbytes) 32768
coredump(blocks) 2097151
nofiles(descriptors) 2000
更改命令为:
来自 “ ITPUB博客 ” ,链接:http://blog.itpub.net/7104/viewspace-133922/,如需转载,请注明出处,否则将追究法律责任。
转载于:http://blog.itpub.net/7104/viewspace-133922/