带有Fedora Linux的HP打印机19

How to use HP Printer connected with USB on Fedora Linux 19.

在Fedora Linux 19上如何使用通过USB连接的HP打印机。

Install these packages and it may ask you to download and install other plugins. Without these packages, my printer does work.

安装这些软件包， 可能会要求您下载并安装其他插件。 没有这些软件包，我的打印机可以工作。

# yum install hplip hplip-gui hpijs

Answered by anonymous.

匿名回答。

---

---

May also need to run:

可能还需要运行：

# hp-plugin

to install plugins for the HP printer.

为HP打印机安装插件。

---

---

This plays the trick when the printer stops to work after rebooting/resetting/etc.

重新启动/重置/等后打印机停止工作时，这将起到欺骗作用。

---

---

After I install related driver software of HP printer as follows.

按照以下步骤安装HP打印机的相关驱动程序软件后。

yum install hplip hplip-gui hpijs

I cannot add my printer (HP LaserJet Professional p1606dn) by hp-setup.
The problem is that I cannot download the plug-in binary from default destination. Then I get hplip-3.14.1.run (http://hplipopensource.com/hplip-web/gethplip.html) and run it. However, It still cannot download the plug-in binary and the whole procedure is here (http://hplipopensource.com/hplip-web/install/install/index.html). At last, I successfully add my printer by HP Device Manager as follows.

我无法通过hp-setup添加打印机（HP LaserJet Professional p1606dn）。
问题是我无法从默认目标位置下载插件二进制文件。 然后，我得到hplip-3.14.1.run（ http://hplipopensource.com/hplip-web/gethplip.html ）并运行它。 但是，它仍然无法下载插件二进制文件，并且整个过程在此处（ http://hplipopensource.com/hplip-web/install/install/index.html ）。 最后，我通过HP设备管理器成功添加了打印机，如下所示。

1, Start HP Device Manager (You can start HP Device Manager by searching in the Activities on Fedora).
2, Setup Device and add your printer.

1， 启动 HP设备管理器（您可以通过在Fedora上的“活动”中搜索来启动HP设备管理器）。
2，设置设备并添加打印机。

Note: If driver cannot find your printer itself, you can type in the IP address to help the driver find your printer.

注意：如果驱动程序找不到您自己的打印机，则可以键入IP地址以帮助驱动程序找到您的打印机。

---

---

Sometimes, your printer may show you “Rendering Completed” so that you cannot print anything by it. The solution is that you need add your printer again by above way. After the new printer works well for you, you can remove the old one.

有时，您的打印机可能会显示“渲染已完成”，因此您无法通过它进行任何打印。 解决方案是您需要通过上述方式再次添加打印机。 新打印机适合您后，您可以卸下旧打印机。

NB: You can input the ip of your printer and add it manually.

注意：您可以输入打印机的IP并手动添加。

翻译自: https://www.systutorials.com/hp-printer-with-fedora-linux-19/