Galileo+wifi+cam

Galileo GEN2代   在串口上 用杜邦线 连STC下载器   COM6口  115200波特率

输入 root

登录进去

或者在boot时

按C键  

wifi部分 在arduinoIDE里面有代码  

cam部分涉及到 BPS 应该看Intel  Galileo
Board User Guide

参考这个！！！！

http://bbs.ickey.cn/group-topic-id-22563.html

http://blog.csdn.net/iambest007/article/details/23702009

首先在PCI-e插槽插入无线网卡，系统上电

1  通过putty进入linux后，以root登录，ifconfig应该可以发现eth0，lo，wlan0这三个网卡

（我没有wlan0这个  不过好像不影响啊）

ifup wlan0 启动wlan0

iwlist wlan0 scan>>wifis.txt

再viwifis.txt  记住SSID

编辑  vi /etc/wpa_supplicant.conf  按照如下格式改写你的conf文件

ctrl_interface=DIR=/var/run/wpa_supplicant GROUP=netdev

update_config=1

network={

ssid="__SSID__"

proto=RSN

key_mgmt=WPA-PSK

pairwise=CCMP TKIP

group=CCMP TKIP

psk="__PASSWORD__"

}

我在做这步的时候老是 弹出WLAN什么的干扰

失败了

直接转到英文大神 去看

http://www.malinov.com/Home/sergey-s-blog/intelgalileo-addingwifi

最后这样做的很成功的

1手机开热点

2root登录

3

root@clanton:~# wpa_passphrase 我wifi名字 << EOF > /etc/wpa_supplicant.conf
> wifi密码
> EOF

4

 ifconfig wlan0 up 

5

If you wish to configure your Galileo to connect to the wireless network automatically, edit /etc/network/interfaces file and add auto wlan0 line somewhere in the file. I suggest putting it right before iface wlan0 line:

# /etc/network/interfaces -- configuration file for ifup(8), ifdown(8)

# The loopback interface
auto lo
iface lo inet loopback

# Wireless interfaces
auto wlan0
iface wlan0 inet dhcp
        wireless_mode managed
        wireless_essid any
        wpa-driver wext
        wpa-conf /etc/wpa_supplicant.conf

6

Restart networking:

root@clanton:/etc# /etc/init.d/networking restart
Running /etc/init.d/networking restart is deprecated because it may not enable again some interfaces
Reconfiguring network interfaces...
ifdown: interface wlan0 not configured
ifdown: interface eth0 not configured
udhcpc (v1.20.2) started
Sending discover...
Sending select for 192.168.1.9...
Lease of 192.168.1.9 obtained, lease time 86400
/etc/udhcpc.d/50default: Adding DNS 192.168.1.254
udhcpc (v1.20.2) started
Sending discover...
Sending discover...
Sending discover...
No lease, failing

跟外国大神的 还不一样啊！！

7

root@clanton:/etc# ifup wlan0
Successfully initialized wpa_supplicant
[ 1186.273174] iwlwifi 0000:01:00.0: L1 Disabled; Enabling L0S
[ 1186.287015] iwlwifi 0000:01:00.0: Radio type=0x2-0x1-0x0
[ 1186.563247] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
udhcpc (v1.20.2) started
Sending discover...
[ 1189.866932] wlan0: authenticate with c8:60:00:d2:95:2c
[ 1189.888080] wlan0: send auth to c8:60:00:d2:95:2c (try 1/3)
Sending discover...
[ 1190.100271] wlan0: send auth to c8:60:00:d2:95:2c (try 2/3)
[ 1190.106813] wlan0: authenticated
[ 1190.120257] wlan0: associate with c8:60:00:d2:95:2c (try 1/3)
[ 1190.127349] wlan0: RX AssocResp from c8:60:00:d2:95:2c (capab=0x11 status=0 aid=2)
[ 1190.159137] wlan0: associated
[ 1190.162421] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
Sending discover...
Sending select for 192.168.1.9...
Lease of 192.168.1.9 obtained, lease time 86400
/etc/udhcpc.d/50default: Adding DNS 192.168.1.254




成功了











最佳的方法是：   参考   http://bbs.ednchina.com/BLOG_ARTICLE_3024963.HTM

1 root登录

2

wpa_passphrase  baobei1026（无线网络名称）13013118589ss（ 密码）   ----->欢迎来蹭网哈

得到的wpa.conf内容为：

network={
        ssid="baobei1026"
        #psk="13013118589ss"
        psk=0125aa2c4e922eb75540fa88e131d735389e26916bbbb670b3a81573211d35cf
}

3

vi /etc/wpa_supplicant.conf  进行编辑，添加

network={
        ssid="baobei1026"
        #psk="13013118589ss"
        psk=0125aa2c4e922eb75540fa88e131d735389e26916bbbb670b3a81573211d35cf
}

4

 vi /etc/network/interfaces  配置网络接口

在2处添加 auto wlan0,3处的any替换成baobei1026（无线网络名）

5

ifup wlan0 连接无线网

失败了！！！！

6显示的内容也不对啊

7

好像必须先 ifconfig wlan0 up 才行

8再ifup wlan0 连接无线网

就可以了

现在我用命令行的形式让Gal连接上了pc上的wifi