WinCE5.0 SMDK2410 BSP在GEC2410开发板上的移植(2)-基于Nand Flash的Eboot

有了NBoot进行复制引导，Eboot就能运行在RAM中了，WinCE5.0自带SMDK2410 BSP与GEC2410硬件配置很接近，只要进行少量的修改就能运行在GEC2410上了。

一、开发环境
编译器: Platform Builder 5.0
目标板: GEC2410 S3C2410A,NAND Flash:64M K9F1208,NOR Flash:2M SST39VF1601 SDRAM 64M,CS8900

二、开始移植
1.Clone一个SMDK2410的BSP，并改名为GEC2410
2.GEC2410\src\bootloader\eboot\下为Eboot的代码，打开main.c，只有LCD和Eboot配置信息两块代码需要修改，网卡用的都是CS8900A，不需要修改，如果网卡不一样需要修改网卡驱动，网卡驱动在\WINCE500\PUBLIC\COMMON\OAK\DRIVERS\ETHDBG下
3.LCD驱动
由于LCD和原BSP中的不一样，相关参数需要修改，到板子自带的eboot中找到相应参数的数值

InitDisplay

1 static void InitDisplay( void )
2 {
3 volatile S3C2410X_IOPORT_REG * s2410IOP = (S3C2410X_IOPORT_REG * )OALPAtoVA(S3C2410X_BASE_REG_PA_IOPORT, FALSE);
4 volatile S3C2410X_LCD_REG * s2410LCD = (S3C2410X_LCD_REG * )OALPAtoVA(S3C2410X_BASE_REG_PA_LCD, FALSE);
5
6 // Set up the LCD controller registers to display a power-on bitmap image.
7 //
8   s2410IOP -> GPCUP = 0xFFFFFFFF ;
9 s2410IOP -> GPCCON = 0xAAAA56A9 ; // 0xAAAAAAAA
10
11 s2410IOP -> GPDUP = 0xFFFFFFFF ;
12 s2410IOP -> GPDCON = 0xAAAAAAAA ;
13
14 s2410LCD -> LCDCON1 = ( 5 << 8 ) | /* VCLK = HCLK / ((CLKVAL + 1) * 2) -> About 7 Mhz */
15 ( 0 << 7 ) | /* 0 : Each Frame */
16 ( 3 << 5 ) | /* TFT LCD Pannel */
17 ( 12 << 1 ) | /* 16bpp Mode */
18 ( 0 << 0 ) ; /* Disable LCD Output */
19
20 s2410LCD -> LCDCON2 = ( 2 << 24 ) | /* VBPD : 2 */
21 (LCD_LINEVAL_TFT << 14 ) | /* Vertical Size : 320 - 1 */
22 ( 2 << 6 ) | /* VFPD : 2 */
23 ( 4 << 0 ) ; /* VSPW : 4 */
24
25 s2410LCD -> LCDCON3 = ( 8 << 19 ) | /* HBPD : 8 */
26 (LCD_HOZVAL_TFT << 8 ) | /* HOZVAL_TFT : 240 - 1 */
27 ( 8 << 0 ) ; /* HFPD : 8 */
28
29
30 s2410LCD -> LCDCON4 = (LCD_MVAL << 8 ) | /* MVAL : 13 */
31 ( 6 << 0 ) ; /* HSPW : 6 */
32
33 s2410LCD -> LCDCON5 = ( 0 << 12 ) | /* BPP24BL : LSB valid */
34 ( 1 << 11 ) | /* FRM565 MODE : 5:6:5 Format */
35 ( 0 << 10 ) | /* INVVCLK : VCLK Falling Edge */
36 ( 0 << 9 ) | /* INVVLINE : Inverted Polarity */
37 ( 0 << 8 ) | /* INVVFRAME : Inverted Polarity */
38 ( 0 << 7 ) | /* INVVD : Normal */
39 ( 0 << 6 ) | /* INVVDEN : Normal */
40 ( 0 << 5 ) | /* INVPWREN : Normal */
41 ( 0 << 4 ) | /* INVENDLINE : Normal */
42 ( 0 << 3 ) | /* PWREN : Disable PWREN */
43 ( 0 << 2 ) | /* ENLEND : Disable LEND signal */
44 ( 0 << 1 ) | /* BSWP : Swap Disable */
45 ( 1 << 0 ) ; /* HWSWP : Swap Enable */
46
47 s2410LCD -> LCDSADDR1 = ((IMAGE_FRAMEBUFFER_DMA_BASE >> 22 ) << 21 ) |
48 ((M5D(IMAGE_FRAMEBUFFER_DMA_BASE >> 1 )) << 0 );
49
50 s2410LCD -> LCDSADDR2 = M5D((IMAGE_FRAMEBUFFER_DMA_BASE + (LCD_XSIZE_TFT * LCD_YSIZE_TFT * 2 )) >> 1 );
51
52 s2410LCD -> LCDSADDR3 = (((LCD_XSIZE_TFT - LCD_XSIZE_TFT) / 1 ) << 11 ) | (LCD_XSIZE_TFT / 1 );
53
54 s2410LCD -> LCDINTMSK |= 3 ; // MASK LCD Sub Interrupt
55 s2410LCD -> LPCSEL |= ~ 0x7 ;
56
57 s2410LCD -> TPAL = 0x0 ;
58 s2410LCD -> LCDCON1 |= 1 ;
59
60 // Display a bitmap image on the LCD...
61 //
62 memcpy(( void * )IMAGE_FRAMEBUFFER_UA_BASE, ScreenBitmap, LCD_ARRAY_SIZE_TFT_16BIT);
63
64 }

这样Eboot就可以显示一副图片了，要是想减少Eboot的尺寸，LCD这块也可不要
4.Eboot 配置信息
(1)函数ResetBootConfig中有Eboot配置的初始信息

1 static void ResetBootConfig(PBOOT_CFG pBootCfg)
2 {
3 // Default eboot configuration values (leave the MAC address field alone)...
4 //
5 pBootCfg -> Signature = CONFIG_SIGNATURE;
6 pBootCfg -> VerMajor = EBOOT_VERSION_MAJOR;
7 pBootCfg -> VerMinor = EBOOT_VERSION_MINOR;
8 pBootCfg -> BootDelay = CONFIG_AUTOBOOT_DEFAULT_COUNT;
9 pBootCfg -> ConfigFlags = CONFIG_FLAGS_AUTOBOOT; // not use DHCP CONFIG_FLAGS_DHCP;
10 pBootCfg -> IPAddr = inet_addr( " 192.168.0.5 " );
11 pBootCfg -> SubnetMask = inet_addr( " 255.255.255.0 " );
12 pBootCfg -> LoadDeviceOrder = 0 ;
13
14 return ;
15 }

(2)该信息保存在Flash中，由于Eboot目前保存在Nand Flash中，因此该信息也保存在Nand Flash中。
定义Eboot配置在Nand Flash中的位置大小,只需要一个Sector就可以了(512Bytes)

1 // EBOOT CONFIG IN NAND FLASH
2 #define EBOOT_CONFIG_BLOCK 19
3 #define EBOOT_CONFIG_SECTOR 19*32
4 #define EBOOT_CONFIG_SECTOR_SIZE 1

(3)原Eboot用的Nor Flash(AM29LV800),需要在OEMPlatformInit函数中注释掉AM29LV800_Init((UINT32)AMD_FLASH_START)的初始化函数
(4)实现ReadBootConfig和WriteBootConfig函数
我们用的NandFlash(K9F1208)的驱动已经有了，只需调用fmd下的flash读写函数即可。该库位于src\common\smartmedia\fmd\fmd.cpp

ReadBootConfig

1 static BOOL ReadBootConfig(PBOOT_CFG pBootCfg)
2 {
3 BOOLEAN bResult = FALSE;
4 char temp[ 512 ]; // store EBOOT_CONFIG_SECTOR
5 OALMSG(OAL_FUNC, (TEXT( " +ReadBootConfig.\r\n " )));
6
7 // Valid caller buffer?
8 if ( ! pBootCfg)
9 {
10 OALMSG(OAL_ERROR, (TEXT( " ERROR: Bad caller buffer.\r\n " )));
11 goto CleanUp;
12 }
13
14 // Read settings from flash...
15 //
16 if ( ! FMD_ReadSector(EBOOT_CONFIG_SECTOR, (PBYTE)temp, NULL, EBOOT_CONFIG_SECTOR_SIZE))
17 {
18 OALMSG(OAL_ERROR, (TEXT( " ERROR: Flash read failed.\r\n " )));
19 goto CleanUp;
20 }
21 memcpy(pBootCfg,(PBOOT_CFG)temp, sizeof (BOOT_CFG));
22
23 // Check configuration signature...
24 //
25 if (pBootCfg -> Signature != CONFIG_SIGNATURE)
26 {
27 OALMSG(OAL_WARN, (TEXT( " WARNING: Boot configuration signature invalid - choosing defaults...\r\n " )));
28 ResetBootConfig(pBootCfg);
29 WriteBootConfig(pBootCfg);
30 }
31
32 bResult = TRUE;
33
34 CleanUp:
35
36 OALMSG(OAL_FUNC, (TEXT( " -ReadBootConfig\r\n " )));
37
38 return (bResult);
39 }

WriteBootConfig

1 static BOOL WriteBootConfig(PBOOT_CFG pBootCfg)
2 {
3 BOOL bResult = FALSE;
4
5 OALMSG(OAL_FUNC, (TEXT( " +WriteBootConfig.\r\n " )));
6
7 if ( ! pBootCfg)
8 {
9 goto CleanUp;
10 }
11
12 // First, erase the eboot settings area in flash...
13 //
14 if ( ! FMD_EraseBlock(EBOOT_CONFIG_BLOCK))
15 {
16 OALMSG(OAL_ERROR, (TEXT( " ERROR: WriteEbootConfig: Flash erase failed.\r\n " )));
17 goto CleanUp;
18 }
19 // Write settings to flash...
20 //
21 if ( ! FMD_WriteSector(EBOOT_CONFIG_SECTOR, (PBYTE)pBootCfg, NULL,EBOOT_CONFIG_SECTOR_SIZE))
22 {
23 OALMSG(OAL_ERROR, (TEXT( " ERROR: WriteEbootConfig: Flash write failed.\r\n " )));
24 goto CleanUp;
25 }
26
27 bResult = TRUE;
28
29 CleanUp:
30 OALMSG(OAL_FUNC, (TEXT( " -WriteBootConfig.\r\n " )));
31 return (bResult);
32 }

5.Debug Serial
为了不与之后的内核中的串口驱动冲突，Eboot使用UART1 38400bps的串口输出
代码位于src\kernel\oal\debug.c

1 #ifdef UART1_38400
2 // GPH4 and GHP5 are UART1 Tx and Rx, respectively.
3 //
4 CLRREG32( & pIOPortReg -> GPHCON, ( 3 << 8 ) | ( 3 << 10 ));
5 SETREG32( & pIOPortReg -> GPHCON, ( 2 << 8 ) | ( 2 << 10 ));
6 // Disable pull-up on TXD1 and RXD1.
7 //
8 SETREG32( & pIOPortReg -> GPHUP, ( 1 << 4 ) | ( 1 << 5 ));
9 // UART1 (TXD1 & RXD1) used for debug serial.
10 //
11 g_pUARTReg = (S3C2410X_UART_REG * )OALPAtoVA(S3C2410X_BASE_REG_PA_UART1, FALSE);
12 // Configure the UART.
13 //
14 OUTREG32( & g_pUARTReg -> UFCON, BSP_UART1_UFCON);
15 OUTREG32( & g_pUARTReg -> UMCON, BSP_UART1_UMCON);
16 OUTREG32( & g_pUARTReg -> ULCON, BSP_UART1_ULCON);
17 OUTREG32( & g_pUARTReg -> UCON, BSP_UART1_UCON);
18 OUTREG32( & g_pUARTReg -> UBRDIV, BSP_UART1_UBRDIV);
19 #endif

三、移植结果

转载于:https://www.cnblogs.com/shevsten/articles/1764462.html