SOPC 8位数码管动态扫描的定制IP

SOPC 8位数码管动态扫描的定制IP

http://www.cnblogs.com/Neddy/archive/2010/07/08/1773983.html

8位数码管的IP，是动态扫描的

//SEG.v

module SEG(clk,reset_n,address,write,writedata,SEG,COM); 
input clk; 
input reset_n; 
input address; 
input write; 
input [31:0] writedata; 
output [7:0] SEG;   //共阳极数码管的段码
output [7:0] COM;  //位码

reg [31:0] data; //address为0时writedata的寄存器
reg [7:0] SEG;
reg [7:0] COM;

//地址译码

always @ (posedge clk or negedge reset_n) 
begin 
     if(reset_n==1'b0)  data <=8'b1111_1111; 
     else if(write && (!address)) data <= writedata;
end 

//scan counter
reg[15:0] cnt_scan;

always@(posedge clk or negedge  reset_n)
begin
 if(!reset_n) cnt_scan<=0;
 else cnt_scan<=cnt_scan+1'b1;
end

reg [3:0] data_buf;//32位writedata,每四位显示一个数码管

//动态扫描

always @(cnt_scan)
begin
   case(cnt_scan[15:13])
       3'b000 :begin COM <= 8'b1111_1110;data_buf=data[3:0];end
       3'b001 :begin COM <= 8'b1111_1101;data_buf=data[7:4];end
       3'b010 :begin COM <= 8'b1111_1011;data_buf=data[11:8];end
       3'b011 :begin COM <= 8'b1111_0111;data_buf=data[15:12];end
       3'b100 :begin COM <= 8'b1110_1111;data_buf=data[19:16];end
       3'b101 :begin COM <= 8'b1101_1111;data_buf=data[23:20];end
       3'b110 :begin COM <= 8'b1011_1111;data_buf=data[27:24];end
       3'b111 :begin COM <= 8'b0111_1111;data_buf=data[31:28];end
       default: COM <= 8'b1111_1111;
    endcase
end

//段码译码
always @(data_buf)
begin
   begin
 case(data_buf)
 8'h0 : SEG <= 8'b1100_0000;  // 0
 8'h1 : SEG <= 8'b1111_1001;  //1

 8'h2 : SEG <= 8'b1010_0100;  //2
 8'h3 : SEG <= 8'b1011_0000;  //3
 8'h4 : SEG <= 8'b1001_1001; //4
 8'h5 : SEG <= 8'b1001_0010; //5
 8'h6 : SEG <= 8'b1000_0010; //6
 8'h7 : SEG <= 8'b1111_1000; //7
 8'h8 : SEG <= 8'b1000_0000;  //8
 8'h9 : SEG <= 8'b1001_0000; //9
 8'ha : SEG <= 8'b1011_1111; //-
 default: SEG <= 8'b1111_1111;//不显示 
 endcase
 end
end 

endmodule

在SOPC的File/New Component 添加SEG.v文件

在signal中将SEG和COM的Interface改为New conduit , Signal type改为export

在点击Finish……

添加CPU  NIOS II/s  , SDRAM ,Timer 周期设为1s，再添加PLL，CO设为50MHz 相位-75度，C1  50MHz 相位0度,最后添加SEG

pll.c0改名为sd_clk,SDRAM的时钟，pll.c1改名为sys_clk,NIOS 的系统时钟

将CPU，SDRAM，timer和SEG_0的Clock改为sys_clk

将Quartus II工程的BDF中添加刚才建立的SOPC

引脚配置，运行OK后下载到FPGA中

现在我们看软件的编写：

#include <stdio.h>
#include "system.h"
#include "alt_types.h"
#include "sys/alt_irq.h"
#include "altera_avalon_timer_regs.h"

#define seg  *(volatile unsigned long *) SEG_0_BASE   //数码管IP的基地址

unsigned char second,minute,hour;//秒，分，小时

static void timer_interrupt(void* context,alt_u32 id)  //timer 计时1s中断
{
      second++;
      if(second==60)
      {
        second=0;
        minute++;
        if(minute==60)
        {
            minute=0;
            hour++;
            if(hour==24)   hour=0;
        }
      }
   IOWR_ALTERA_AVALON_TIMER_STATUS(TIMER_BASE,0);//清楚中断溢出位
}

int main(void)  //alt_main()不响应中断，故用main()
{

    second=0;

   minute=0;

   hour=12;
    alt_irq_register(TIMER_IRQ,0,timer_interrupt);//中断登记函数
    IOWR_ALTERA_AVALON_TIMER_STATUS(TIMER_BASE,0);//清楚中断溢出位
    IOWR_ALTERA_AVALON_TIMER_CONTROL(TIMER_BASE,7);//开始计时
    while(1)
    {
       seg = ((hour/10)<<28)+((hour%10)<<24)+(10<<20)+((minute/10)<<16)
             +((minute%10)<<12)+(10<<8)+((second/10)<<4)+(second%10);  //显示格式  12-00-00
    }
    return 0;
}

转载于:https://www.cnblogs.com/GL-BBL/archive/2012/08/22/2651716.html