Power on reset
Env.Os_Auto_Flag=1
<*******************************************>
<* *>
<* S3C2410 Board BIOS V2008 *>
<* *>
<* Henan Polytechnic University *>
<* *>
<* 董利强 *>
<* *>
<* ^_^ Love you every day ^_^ *>
<* *>
<*******************************************>
NAND Flash Boot
Please select function :
0 : USB download file
1 : Uart download file
2 : Write Nand flash with download file
3 : Load Pragram from Nand flash and run
4 : Erase Nand flash regions
5 : Write NOR flash with download file
6 : Set boot params
7 : Set AutoBoot parameter,1:linux 2:wince
Set boot params = root=1f02 init=/linuxrc console=ttyS0,115200 devfs=mount display=dh240
Linux version 2.6.8.1-ptx1 (root@linuxserver) (gcc version 3.3.2) #245 Thu Mar 6 10:25:09 EST 2008
CPU: ARM920Tid(wb) [41129200] revision 0 (ARMv4T)
CPU: D VIVT write-back cache
CPU: I cache: 16384 bytes, associativity 64, 32 byte lines, 8 sets
CPU: D cache: 16384 bytes, associativity 64, 32 byte lines, 8 sets
Machine: SMDK2410
ATAG_INITRD is deprecated; please update your bootloader.
Memory policy: ECC disabled, Data cache writeback
S3C2410: core 200.000 MHz, memory 100.000 MHz, peripheral 50.000 MHz
Built 1 zonelists
Kernel command line: root=1f02 init=/linuxrc console=ttyS0,115200 devfs=mount display=dh240
irq: clearing pending status 00002000
irq: clearing subpending status 00000092
irq: clearing subpending status 00000092
irq: clearing subpending status 00000092
irq: clearing subpending status 00000092
Trying to install chained handler for IRQ47
PID hash table entries: 512 (order 9: 4096 bytes)
setup_timer tcon=00090d09, tcnt c350, tcfg 0000040f,00001032
Console: colour dummy device 80x30
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 64MB = 64MB total
Memory: 61904KB available (2249K code, 487K data, 128K init)
Calibrating delay loop... 99.94 BogoMIPS
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
CPU: Testing write buffer coherency: ok
NET: Registered protocol family 16
S3C2410: Initialising architecture
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
VA=0xffc00000, PA=0x30380000, size=0x00027000
NetWinder Floating Point Emulator V0.97 (double precision)
devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
NTFS driver 2.1.15 [Flags: R/W].
yaffs Mar 6 2008 10:21:10 Installing.
Console: switching to colour frame buffer device 40x30
s3c2410ts init
s3c2410ts device driver MAJOR:253
s3c2410ts initialized
S3C2410 Real Time Clock Driver v0.1
S3C2410X Serial, (c) 2003 Simtec Electronics
ttyS0 at MMIO 0x50000000 (irq = 70) is a S3C2410
ttyS1 at MMIO 0x50004000 (irq = 73) is a S3C2410
ttyS2 at MMIO 0x50008000 (irq = 76) is a S3C2410
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
loop: loaded (max 8 devices)
Using anticipatory io scheduler
nbd: registered device at major 43
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
NET: Registered protocol family 24
Cirrus Logic CS8900A driver for Linux (V0.02)
eth0: CS8900A rev E detected
Universal TUN/TAP device driver 1.5 (C)1999-2002 Maxim Krasnyansky
Linux video capture interface: v1.00
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 50MHz system bus speed for PIO modes; override with idebus=xx
ide_register_hw return -1
NAND device: Manufacturer ID: 0xec, Chip ID: 0x76 (Samsung NAND 64MiB 3,3V 8-bit)
Scanning device for bad blocks
Creating 5 MTD partitions on "NAND 64MiB 3,3V 8-bit":
0x00000000-0x00040000 : "boot"
0x00040000-0x00200000 : "kernel"
0x00200000-0x02000000 : "rootfs"
0x02000000-0x03000000 : "ext-fs1"
0x03000000-0x04000000 : "ext-fs2"
drivers/usb/host/ohci-s3c2410.c: ohci_hcd (S3C2410) at 0xf0200000, irq 42
s3c2410-ohci s3c2410-ohci5: new USB bus registered, assigned bus number 1
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.0:USB HID core driver
mice: PS/2 mouse device common for all mice
s3c2410kbd_init
s3c2410-maxtrixkb successfully loaded
S3C2410-UDA1341 Probe
UDA1341 audio driver initialized
NET: Registered protocol family 2
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 4096 bind 8192)
NET: Registered protocol family 1
NET: Registered protocol family 17
VFS: Mounted root (cramfs filesystem) readonly.
Mounted devfs on /dev
Freeing init memory: 128K
mount /etc as ramfs
re-create the /etc/mtab entries
Using /usr/sd_mod.ko
Using /usr/usb-storage.ko
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
Using /usr/usbvideo.ko
Using /usr/ov511.ko
usbcore: registered new driver ov511
drivers/usb/media/ov511.c: v1.64 for Linux 2.5 : ov511 USB Camera Driver
mount: Mounting none on /proc/bus/usb failed: No such file or directory
Please press Enter to activate this console. cirrus_start: requesting interrupt 53
eth0: register interrupt 53
ln: /dev/touchscreen/0: File exists
Could not open mime.types file, "etc/mime.types", for reading
mount: Mounting /dev/nfblock/3 on /tmp/flashdisk failed: No such file or directory
mount: Mounting /dev/nfblock/2 on /tmp/mplayer failed: No such file or directory
[9;0][?33l[?25lCould not read calibration: /etc/pointercal
Create pluginlibman in libqpe
Use QPEApplication's PluginLibraryManager
Setting up QCop to QPE/System
channel QPE/Card added
channel QPE/Server added
channel QPE/IME added
Create pluginlibman in libqpe
Use QPEApplication's PluginLibraryManager
QuickLauncher running
channel QPE/Application/quicklauncher added
channel QPE/QuickLauncher-324 added
Registered QPE/QuickLauncher-324
ln: /dev/touchscreen/0: File exists
[root@(none) /]#