Linux version 2.6.22.18-ADI-2008R1-svn (root@ippbx) (gcc version 4.1.2 (ADI svn)
) #88 Tue Aug 19 10:48:40 CST 2008
Hardware Trace Off and Disabled
Blackfin support (C) 2004-2007 Analog Devices, Inc.
Compiled for ADSP-BF533 Rev 0.5
Blackfin Linux support by http://blackfin.uclinux.org/
Processor Speed: 564 MHz core clock and 80 MHz System Clock
Board Memory: 64MB
Kernel Managed Memory: 64MB
Memory map:
text = 0x00001000-0x00172fc0
rodata = 0x00173000-0x001dd5d8
data = 0x001de000-0x001f2000
stack = 0x001de000-0x001e0000
init = 0x001f2000-0x00208000
bss = 0x00208000-0x0021a608
available = 0x0021a608-0x03eff000
DMA Zone = 0x03f00000-0x04000000
Instruction Cache Enabled
Data Cache Enabled (write-back)
Built 1 zonelists. Total pages: 16002
Kernel command line: root=/dev/mtdblock2 rw rootfstype=jffs2
Configuring Blackfin Priority Driven Interrupts
PID hash table entries: 256 (order: 8, 1024 bytes)
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory available: 61776k/65536k RAM, (88k init code, 1479k kernel code, 582k data, 1024k dma, 584k reserved)
Blackfin Scratchpad data SRAM: 4 KB
Blackfin Data A SRAM: 16 KB (15 KB free)
Blackfin Data B SRAM: 16 KB (16 KB free)
Blackfin Instruction SRAM: 64 KB (56 KB free)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
Blackfin GPIO Controller
Blackfin DMA Controller
stamp_init(): registering device resources
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
NTFS driver 2.1.28 [Flags: R/W DEBUG].
JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
yaffs Aug 19 2008 10:26:06 Installing.
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler cfq registered
bfin-wdt: initialized: timeout=20 sec (nowayout=0)
Registering the device YanSL_LED ok!
Registering the device Relay ok!
Register device YanSL_ENCRYPT ok!
Serial: Blackfin serial driver
bfin-uart.1: ttyBF0 at MMIO 0xffc00400 (irq = 21) is a BFIN-UART
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
PPP MPPE Compression module registered
NET: Registered protocol family 24
dm9000 Ethernet Driver
eth0: dm9000 at 20320300,20320304 IRQ 39 MAC: 46:e6:36:c5:00:26
eth1: dm9000 at 20300300,20300304 IRQ 38 MAC: be:d4:28:55:81:d2
BF5xx-Flash: probing 16-bit flash bus
BF5xx-Flash: Found 1 x16 devices at 0x0 in 16-bit bank
Amd/Fujitsu Extended Query Table at 0x0040
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
cmdlinepart partition parsing not available
RedBoot partition parsing not available
BF5xx-Flash: Using board partition definition
Creating 3 MTD partitions on "BF5xx-Flash":
0x00000000-0x00020000 : "Bootloader"
0x00020000-0x00180000 : "Kernel"
0x00180000-0x00400000 : "RootFS"
NAND device: Manufacturer ID: 0x20, Chip ID: 0x76 (ST Micro NAND 64MiB 3,3V 8-bit)
Scanning device for bad blocks
Creating 1 MTD partitions on "NAND 64MiB 3,3V 8-bit":
) #88 Tue Aug 19 10:48:40 CST 2008
Hardware Trace Off and Disabled
Blackfin support (C) 2004-2007 Analog Devices, Inc.
Compiled for ADSP-BF533 Rev 0.5
Blackfin Linux support by http://blackfin.uclinux.org/
Processor Speed: 564 MHz core clock and 80 MHz System Clock
Board Memory: 64MB
Kernel Managed Memory: 64MB
Memory map:
text = 0x00001000-0x00172fc0
rodata = 0x00173000-0x001dd5d8
data = 0x001de000-0x001f2000
stack = 0x001de000-0x001e0000
init = 0x001f2000-0x00208000
bss = 0x00208000-0x0021a608
available = 0x0021a608-0x03eff000
DMA Zone = 0x03f00000-0x04000000
Instruction Cache Enabled
Data Cache Enabled (write-back)
Built 1 zonelists. Total pages: 16002
Kernel command line: root=/dev/mtdblock2 rw rootfstype=jffs2
Configuring Blackfin Priority Driven Interrupts
PID hash table entries: 256 (order: 8, 1024 bytes)
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory available: 61776k/65536k RAM, (88k init code, 1479k kernel code, 582k data, 1024k dma, 584k reserved)
Blackfin Scratchpad data SRAM: 4 KB
Blackfin Data A SRAM: 16 KB (15 KB free)
Blackfin Data B SRAM: 16 KB (16 KB free)
Blackfin Instruction SRAM: 64 KB (56 KB free)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
Blackfin GPIO Controller
Blackfin DMA Controller
stamp_init(): registering device resources
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
NTFS driver 2.1.28 [Flags: R/W DEBUG].
JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
yaffs Aug 19 2008 10:26:06 Installing.
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler cfq registered
bfin-wdt: initialized: timeout=20 sec (nowayout=0)
Registering the device YanSL_LED ok!
Registering the device Relay ok!
Register device YanSL_ENCRYPT ok!
Serial: Blackfin serial driver
bfin-uart.1: ttyBF0 at MMIO 0xffc00400 (irq = 21) is a BFIN-UART
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
PPP MPPE Compression module registered
NET: Registered protocol family 24
dm9000 Ethernet Driver
eth0: dm9000 at 20320300,20320304 IRQ 39 MAC: 46:e6:36:c5:00:26
eth1: dm9000 at 20300300,20300304 IRQ 38 MAC: be:d4:28:55:81:d2
BF5xx-Flash: probing 16-bit flash bus
BF5xx-Flash: Found 1 x16 devices at 0x0 in 16-bit bank
Amd/Fujitsu Extended Query Table at 0x0040
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
cmdlinepart partition parsing not available
RedBoot partition parsing not available
BF5xx-Flash: Using board partition definition
Creating 3 MTD partitions on "BF5xx-Flash":
0x00000000-0x00020000 : "Bootloader"
0x00020000-0x00180000 : "Kernel"
0x00180000-0x00400000 : "RootFS"
NAND device: Manufacturer ID: 0x20, Chip ID: 0x76 (ST Micro NAND 64MiB 3,3V 8-bit)
Scanning device for bad blocks
Creating 1 MTD partitions on "NAND 64MiB 3,3V 8-bit":
0x00000000-0x08000000 : "file system"
mtd: partition "file system" extends beyond the end of device "NAND 64MiB 3,3V 8-bit" -- size truncated to 0x4000000
sl811: driver sl811-hcd, 19 May 2005
rtc-bfin rtc-bfin: rtc core: registered rtc-bfin as rtc0
nf_conntrack version 0.5.0 (503 buckets, 4024 max)
IPv4 over IPv4 tunneling driver
ip_tables: (C) 2000-2006 Netfilter Core Team
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
rtc-bfin rtc-bfin: setting the system clock to 1970-01-01 17:42:38 (63758)
VFS: Mounted root (jffs2 filesystem).
Freeing unused kernel memory: 88k freed
dma_alloc_init: dma_page @ 0x00201000 - 256 pages at 0x03f00000
/bin/expand: not found
yaffs: dev is 32505859 name is "mtdblock3"
yaffs: passed flags ""
yaffs: Attempting MTD mount on 31.3, "mtdblock3"
sqlite: not found
Network settings begin:
eth0_set
eth0: link down
72:A3:D2:70:56:F7
eth1: link down
72:A3:D2:70:56:F7
eth1: link down
10.0.0.70 255.255.255.0
route: SIOC[ADD|DEL]RT: No such process
10.0.0.2
eth1: link up, 100Mbps, full-duplex, lpa 0x45E1
sqlite: not found
[: 0: unknown operand
nftest: module license 'unspecified' taints kernel.
Zapata Telephony Interface Registered on major 196
[01/Jan/1970:17:42:47 +0000] boa: server version Boa/0.94.14rc21
[01/Jan/1970:17:42:47 +0000] boa: server built Aug 19 2008 at 10:57:05.
[01/Jan/1970:17:42:47 +0000] boa: starting server pid=834, port 80
Module 0: Installed -- AUTO FXO (CHINA mode)
Module 1: Installed -- AUTO FXO (CHINA mode)
DAA not found!
Module 2: Not installed
DAA not found!
Module 3: Not installed
Found: SIPSYS STAMP (4 modules)
Registered tone zone 0 (United States / North America)
_____________________________________
a8888b. / Welcome to the uClinux distribution /
d888888b. / _ _ /
8P"YP"Y88 / | | |_| __ __ (TM) |
8|o||o|88 _____/ | | _ ____ _ _ / // / |
8' .88 / | | | | _ /| | | | / / |
8`._.' Y8. / | |__ | | | | | |_| | / / |
d/ `8b. / /____||_|_| |_|/____|/_//_/ |
dP . Y8b. / For embedded processors including |
d8:' " `::88b / the Analog Devices Blackfin /
d8" 'Y88b /___________________________________/
:8P ' :888
8a. : _a88P For further information, check out:
._/"Yaa_: .| 88P| - http://blackfin.uclinux.org/
/ YP" `| 8P `. - http://docs.blackfin.uclinux.org/
/ /.___.d| .' - http://www.uclinux.org/
`--..__)8888P`._.' jgs/a:f - http://www.analog.com/blackfin
mtd: partition "file system" extends beyond the end of device "NAND 64MiB 3,3V 8-bit" -- size truncated to 0x4000000
sl811: driver sl811-hcd, 19 May 2005
rtc-bfin rtc-bfin: rtc core: registered rtc-bfin as rtc0
nf_conntrack version 0.5.0 (503 buckets, 4024 max)
IPv4 over IPv4 tunneling driver
ip_tables: (C) 2000-2006 Netfilter Core Team
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
rtc-bfin rtc-bfin: setting the system clock to 1970-01-01 17:42:38 (63758)
VFS: Mounted root (jffs2 filesystem).
Freeing unused kernel memory: 88k freed
dma_alloc_init: dma_page @ 0x00201000 - 256 pages at 0x03f00000
/bin/expand: not found
yaffs: dev is 32505859 name is "mtdblock3"
yaffs: passed flags ""
yaffs: Attempting MTD mount on 31.3, "mtdblock3"
sqlite: not found
Network settings begin:
eth0_set
eth0: link down
72:A3:D2:70:56:F7
eth1: link down
72:A3:D2:70:56:F7
eth1: link down
10.0.0.70 255.255.255.0
route: SIOC[ADD|DEL]RT: No such process
10.0.0.2
eth1: link up, 100Mbps, full-duplex, lpa 0x45E1
sqlite: not found
[: 0: unknown operand
nftest: module license 'unspecified' taints kernel.
Zapata Telephony Interface Registered on major 196
[01/Jan/1970:17:42:47 +0000] boa: server version Boa/0.94.14rc21
[01/Jan/1970:17:42:47 +0000] boa: server built Aug 19 2008 at 10:57:05.
[01/Jan/1970:17:42:47 +0000] boa: starting server pid=834, port 80
Module 0: Installed -- AUTO FXO (CHINA mode)
Module 1: Installed -- AUTO FXO (CHINA mode)
DAA not found!
Module 2: Not installed
DAA not found!
Module 3: Not installed
Found: SIPSYS STAMP (4 modules)
Registered tone zone 0 (United States / North America)
_____________________________________
a8888b. / Welcome to the uClinux distribution /
d888888b. / _ _ /
8P"YP"Y88 / | | |_| __ __ (TM) |
8|o||o|88 _____/ | | _ ____ _ _ / // / |
8' .88 / | | | | _ /| | | | / / |
8`._.' Y8. / | |__ | | | | | |_| | / / |
d/ `8b. / /____||_|_| |_|/____|/_//_/ |
dP . Y8b. / For embedded processors including |
d8:' " `::88b / the Analog Devices Blackfin /
d8" 'Y88b /___________________________________/
:8P ' :888
8a. : _a88P For further information, check out:
._/"Yaa_: .| 88P| - http://blackfin.uclinux.org/
/ YP" `| 8P `. - http://docs.blackfin.uclinux.org/
/ /.___.d| .' - http://www.uclinux.org/
`--..__)8888P`._.' jgs/a:f - http://www.analog.com/blackfin
Have a lot of fun...
BusyBox v1.4.1 (2008-08-19 10:57:17 CST) Built-in shell (msh)
Enter 'help' for a list of built-in commands.
root:~>
被折叠的 条评论
为什么被折叠?
到【灌水乐园】发言
