STM32F401RCT6配置I2C驱动AT25C256

1.原理图部分

2.CubeMx配置I2C

3.参数配置：

4.代码区：

#define ADDR_24LCxx_Write 0xA0
#define ADDR_24LCxx_Read 0xA1

#define ATC256_PAGE_SIZE 64
#define ATC256_PAGE_NUM  512

/*读取设备参数*/
static void DeviceParm_Read_at24c256(void)
{
    uint8_t ReadBuffer[ATC256_BUFFER_SIZE] = { 0 };
    HAL_StatusTypeDef status = HAL_OK;
    device_param_t tDeviceInfo;
    memset(&tDeviceInfo, 0 , sizeof(tDeviceInfo));

    status = HAL_I2C_Mem_Read(&hi2c1, ADDR_24LCxx_Read, ATC256_DEVICE_SAVE_PAGE_START, I2C_MEMADD_SIZE_16BIT, ReadBuffer, ATC256_BUFFER_SIZE, 0x1000);
    printf("Read Ret %d\r\n",status);

    memcpy(&tDeviceInfo, ReadBuffer, sizeof(gDeviceInfo));
    if(strlen(tDeviceInfo.DeviceSN) != 0)
    { 
        printf("该设备有初始化SN号码[%s]\r\n", tDeviceInfo.DeviceSN);
    
        memcpy(&gDeviceInfo, ReadBuffer, sizeof(gDeviceInfo));
    } else {
        printf("此设备没有初始化!\r\n");
        TcpSetDefaultlDeviceInfo();
    }
}

/*写设备参数*/
uint8_t DeviceParm_Save_at24c256(void)
{
    uint8_t WriteBuffer[ATC256_BUFFER_SIZE] = { 0 };
    uint8_t ReadBuffer[ATC256_BUFFER_SIZE] = { 0 };
    HAL_StatusTypeDef status = HAL_OK;
    int i =0;
    //拷贝数据到缓存区.
   memcpy(WriteBuffer, &gDeviceInfo, sizeof(gDeviceInfo));
   for(i=0; i<1024/ATC256_PAGE_SIZE; i++) //32 分32次去写 256个 大小 1024 /64 = 16
    {
        if (HAL_I2C_Mem_Write(&hi2c1, ADDR_24LCxx_Write, ATC256_DEVICE_SAVE_PAGE_START+i*ATC256_PAGE_SIZE, I2C_MEMADD_SIZE_16BIT,&(WriteBuffer[i*ATC256_PAGE_SIZE]),ATC256_PAGE_SIZE, 1000) == HAL_OK)
        {
            //printf("\r\n Byte %02d to Byte %02d Write OK",i,i+64);
            HAL_Delay(5);//写完以后需要延时5ms，这个不能少
        }else{
            //printf("\r\n Byte %02d to Byte %02d Write Failed",i,i+8);
        }                
    }

    //TcpPrintProtolDeviceInfo(gDeviceInfo);
    
    //再读一遍
    status = HAL_I2C_Mem_Read(&hi2c1, ADDR_24LCxx_Read, ATC256_DEVICE_SAVE_PAGE_START, I2C_MEMADD_SIZE_16BIT, ReadBuffer, ATC256_BUFFER_SIZE, 0x1000);
    printf("Read Ret %d\r\n",status);
    if(memcmp(ReadBuffer, WriteBuffer, MAX_DEVICE_PARAM_LEN) == 0)
    {
        printf("参数写入成功\r\n");
        return 1;
    } else {
        //printf("设备参数 读写不一致，保存失败!\r\n");
        FaultDecte_Set_Device_Deatil(DEVICE_FAULT_TYPE_STROGE); //读写参数不一样. 保存参数故障
    }
    return 0;
}