c简单的入门程序

1.简单的c语言

#include "sys.h"
#include "uart1.h"
#include "delay.h"

#define LED_CLK()       __HAL_RCC_GPIOB_CLK_ENABLE()
#define LED_GPIO        GPIOB
#define LED_PIN         GPIO_PIN_8

void led_init(void);                       /* LED初始化函数声明 */

int main(void)
{
    HAL_Init();                         /* 初始化HAL库 */
    stm32_clock_init(RCC_PLL_MUL9); /* 设置时钟, 72Mhz */
    led_init();                         /* LED初始化 */
    uart1_init(115200);
    printf("running...\r\n");
    while(1)
    { 
        HAL_GPIO_WritePin(LED_GPIO,LED_PIN,GPIO_PIN_SET);
        delay_ms(500);
        HAL_GPIO_WritePin(LED_GPIO,LED_PIN,GPIO_PIN_RESET);
        delay_ms(500); 
    }
}

/**
 * @brief       初始化LED相关IO口, 并使能时钟
 * @param       无
 * @retval      无
 */
void led_init(void)
{
    GPIO_InitTypeDef gpio_initstruct;
    LED_CLK();                                             /* IO口时钟使能 */

    gpio_initstruct.Pin = LED_PIN;                         /* LED0引脚 */
    gpio_initstruct.Mode = GPIO_MODE_OUTPUT_PP;            /* 推挽输出 */
    gpio_initstruct.Pull = GPIO_PULLUP;                    /* 上拉 */
    gpio_initstruct.Speed = GPIO_SPEED_FREQ_HIGH;          /* 高速 */
    HAL_GPIO_Init(LED_GPIO, &gpio_initstruct);             /* 初始化LED0引脚 */
}

2.HAL_Init();                         /* 初始化HAL库 */

f12看看调用了什么库  具体的方法

调用了 

C:\Users\Administrator\Desktop\base\00. STM32F103工程模板\STM32F103C8T6_Template\Drivers\STM32F1xx_HAL_Driver\Src

C:\Users\Administrator\Desktop\base\00. STM32F103工程模板\STM32F103C8T6_Template\Drivers\STM32F1xx_HAL_Driver\Src

stm32f1xx_hal.c

具体的详细参考

STM32F1xx HAL库 中文详解 之 综合概述（一）_hal库中文手册-CSDN博客

HAL_StatusTypeDef HAL_Init(void)
{
  /* Configure Flash prefetch */
#if (PREFETCH_ENABLE != 0)
#if defined(STM32F101x6) || defined(STM32F101xB) || defined(STM32F101xE) || defined(STM32F101xG) || \
    defined(STM32F102x6) || defined(STM32F102xB) || \
    defined(STM32F103x6) || defined(STM32F103xB) || defined(STM32F103xE) || defined(STM32F103xG) || \
    defined(STM32F105xC) || defined(STM32F107xC)

  /* Prefetch buffer is not available on value line devices */
  __HAL_FLASH_PREFETCH_BUFFER_ENABLE();
#endif
#endif /* PREFETCH_ENABLE */

  /* Set Interrupt Group Priority */
  HAL_NVIC_SetPriorityGrouping(NVIC_PRIORITYGROUP_4);

  /* Use systick as time base source and configure 1ms tick (default clock after Reset is HSI) */
  HAL_InitTick(TICK_INT_PRIORITY);

  /* Init the low level hardware */
  HAL_MspInit();

  /* Return function status */
  return HAL_OK;
}