SUSE Linux 10 下重命名网卡名字

最新推荐文章于 2021-05-16 18:16:28 发布

Leshami

最新推荐文章于 2021-05-16 18:16:28 发布

阅读量1w

点赞数

分类专栏： -----Linux相关特性

本文链接：https://blog.csdn.net/leshami/article/details/8131771

版权

-----Linux相关特性专栏收录该内容

41 篇文章 0 订阅

订阅专栏

前阵子碰到suse linux下网卡重命名的问题，是在虚拟机上安装RAC，通过复制虚拟机后需要完成的。与redhat linux，以及oralce linux不同的处理方式，下面将其记录下来，供参考。

1、新节点的网络配置 
#启动节点之后没有任何IP配置信息   
 bo2dbp:~ # ifconfig
 lo        Link encap:Local Loopback
           inet addr:127.0.0.1  Mask:255.0.0.0
           inet6 addr: ::1/128 Scope:Host
           UP LOOPBACK RUNNING  MTU:16436  Metric:1
           RX packets:174 errors:0 dropped:0 overruns:0 frame:0
           TX packets:174 errors:0 dropped:0 overruns:0 carrier:0
           collisions:0 txqueuelen:0
           RX bytes:11471 (11.2 Kb)  TX bytes:11471 (11.2 Kb)

2、使用yast2/newcard删除之前的网卡，并为新网卡添加IP地址，路由，机器名   
    #下面是删除后并配置ip,route之后的信息   
 bo2dbp:~ # ifconfig
 eth3      Link encap:Ethernet  HWaddr 00:0C:29:99:DF:0F
           inet addr:192.168.7.71  Bcast:192.168.7.255  Mask:255.255.255.0
           inet6 addr: fe80::20c:29ff:fe99:df0f/64 Scope:Link
           UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
           RX packets:10 errors:0 dropped:0 overruns:0 frame:0
           TX packets:4 errors:0 dropped:0 overruns:0 carrier:0
           collisions:0 txqueuelen:1000
           RX bytes:2387 (2.3 Kb)  TX bytes:328 (328.0 b)
 
 eth4      Link encap:Ethernet  HWaddr 00:0C:29:99:DF:19
           inet addr:10.10.7.71  Bcast:10.10.7.255  Mask:255.255.255.0
           inet6 addr: fe80::20c:29ff:fe99:df19/64 Scope:Link
           UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
           RX packets:7 errors:0 dropped:0 overruns:0 frame:0
           TX packets:3 errors:0 dropped:0 overruns:0 carrier:0
           collisions:0 txqueuelen:1000
           RX bytes:1607 (1.5 Kb)  TX bytes:238 (238.0 b)
 
 lo        Link encap:Local Loopback
           inet addr:127.0.0.1  Mask:255.0.0.0
           inet6 addr: ::1/128 Scope:Host
           UP LOOPBACK RUNNING  MTU:16436  Metric:1
           RX packets:206 errors:0 dropped:0 overruns:0 frame:0
           TX packets:206 errors:0 dropped:0 overruns:0 carrier:0
           collisions:0 txqueuelen:0
           RX bytes:13803 (13.4 Kb)  TX bytes:13803 (13.4 Kb)

3、停用网路
 bo2dbp:~ # rcnetwork stop
 Shutting down network interfaces:
     eth3      device: Intel Corporation 82545EM Gigabit Ethernet Controller (Copper) (rev 01)
     eth3      configuration: eth-bus-pci-0000:02:00.0
     eth3                                                              done
     eth4      device: Intel Corporation 82545EM Gigabit Ethernet Controller (Copper) (rev 01)
     eth4      configuration: eth-bus-pci-0000:02:02.0
     eth4                                                              done
 Shutting down service network  .  .  .  .  .  .  .  .  .  .  .  .  .  done

4、编辑配置文件
 #将原来的eth0 与 eth1注释掉
 #并将新的mac地址条目改为eth0与eth1
 bo2dbp:~ # vi /etc/udev/rules.d/30-net_persistent_names.rules
 
 #SUBSYSTEM=="net", ACTION=="add", SYSFS{address}=="00:0c:29:8a:6c:c8", IMPORT="/lib/udev/rename_netiface %k eth0"
 #SUBSYSTEM=="net", ACTION=="add", SYSFS{address}=="00:0c:29:8a:6c:d2", IMPORT="/lib/udev/rename_netiface %k eth1"
 SUBSYSTEM=="net", ACTION=="add", SYSFS{address}=="00:0c:29:99:df:0f", IMPORT="/lib/udev/rename_netiface %k eth0"
 SUBSYSTEM=="net", ACTION=="add", SYSFS{address}=="00:0c:29:99:df:19", IMPORT="/lib/udev/rename_netiface %k eth1"

5、使用rename_netiface命令重命名网络接口
 bo2dbp:~ # cd /lib/udev
 bo2dbp:/lib/udev # ./rename_netiface eth3 eth0
 INTERFACE=eth0
 DEVPATH=/eth0
 RENAMED=yes
 bo2dbp:/lib/udev # ./rename_netiface eth4 eth1
 INTERFACE=eth1
 DEVPATH=/eth1
 RENAMED=yes

6、重启网络
 bo2dbp:/lib/udev # rcnetwork start
 Hint: you may set mandatory devices in /etc/sysconfig/network/config
 Setting up network interfaces:
     lo
     lo        IP address: 127.0.0.1/8
               IP address: 127.0.0.2/8
 Checking for network time protocol daemon (NTPD):                     unused
     lo                                                                done
     eth0      device: Intel Corporation 82545EM Gigabit Ethernet Controller (Copper) (rev 01)
     eth0      configuration: eth-bus-pci-0000:02:00.0
     eth0      IP address: 192.168.7.71/24
 Checking for network time protocol daemon (NTPD):                     unused
     eth0                                                              done
     eth1      device: Intel Corporation 82545EM Gigabit Ethernet Controller (Copper) (rev 01)
     eth1      configuration: eth-bus-pci-0000:02:02.0
     eth1      IP address: 10.10.7.71/24
 Checking for network time protocol daemon (NTPD):                     unused
     eth1                                                              done
 Setting up service network  .  .  .  .  .  .  .  .  .  .  .  .  .  .  done

7、检查结果
 bo2dbp:/lib/udev # ifconfig
 eth0      Link encap:Ethernet  HWaddr 00:0C:29:99:DF:0F
           inet addr:192.168.7.71  Bcast:192.168.7.255  Mask:255.255.255.0
           inet6 addr: fe80::20c:29ff:fe99:df0f/64 Scope:Link
           UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
           RX packets:754 errors:0 dropped:0 overruns:0 frame:0
           TX packets:12 errors:0 dropped:0 overruns:0 carrier:0
           collisions:0 txqueuelen:1000
           RX bytes:136187 (132.9 Kb)  TX bytes:936 (936.0 b)
 
 eth1      Link encap:Ethernet  HWaddr 00:0C:29:99:DF:19
           inet addr:10.10.7.71  Bcast:10.10.7.255  Mask:255.255.255.0
           inet6 addr: fe80::20c:29ff:fe99:df19/64 Scope:Link
           UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
           RX packets:752 errors:0 dropped:0 overruns:0 frame:0
           TX packets:12 errors:0 dropped:0 overruns:0 carrier:0
           collisions:0 txqueuelen:1000
           RX bytes:136065 (132.8 Kb)  TX bytes:936 (936.0 b)
 
 lo        Link encap:Local Loopback
           inet addr:127.0.0.1  Mask:255.0.0.0
           inet6 addr: ::1/128 Scope:Host
           UP LOOPBACK RUNNING  MTU:16436  Metric:1
           RX packets:206 errors:0 dropped:0 overruns:0 frame:0
           TX packets:206 errors:0 dropped:0 overruns:0 carrier:0
           collisions:0 txqueuelen:0
           RX bytes:13803 (13.4 Kb)  TX bytes:13803 (13.4 Kb)

  事实上，我们可以根据上述方法来将网卡设定为有意义的接口名字，如lan0,lan1,public0,public1。

 Author: Robinson
 Blog  : http://blog.csdn.net/robinson_0612

有关基于用户管理的备份和备份恢复的概念请参考

Oracle 基于备份控制文件的恢复(unsing backup controlfile)

有关RMAN的备份恢复与管理请参考

基于catalog 的RMAN 备份与恢复

RMAN 备份路径困惑(使用plus archivelog时)

有关ORACLE体系结构请参考

Oracle 表空间与数据文件

Oracle 密码文件

Oracle 参数文件

Oracle 联机重做日志文件(ONLINE LOG FILE)

Oracle 控制文件(CONTROLFILE)

Oracle 归档日志

Oracle 回滚(ROLLBACK)和撤销(UNDO)

Oracle 数据库实例启动关闭过程

Oracle 10g SGA 的自动化管理

Oracle 实例和Oracle数据库(Oracle体系结构)

Leshami

关注

0
点赞
踩
2

收藏

觉得还不错? 一键收藏
0
评论
SUSE Linux 10 下重命名网卡名字

前阵子碰到suse linux下网卡重命名的问题，是在虚拟机上安装RAC，通过复制虚拟机后需要完成的。与redhat linux，以及oralce linux不同的处理方式，下面将其记录下来，供参考。1、新节点的网络配置 #启动节点之后没有任何IP配置信息 bo2dbp:~ # ifconfig lo Link encap:Local Loopback
复制链接

扫一扫

专栏目录