低功耗调试

delete_module

external/kmod/libkmod/libkmod-module.c +790

system与power相关：

system/core/libsuspend/

system/core/libsuspend/autosuspend_wakeup_count.c:46:static const char *sleep_state = "mem";

iperf的用法

https://blog.51cto.com/dingtongxue1990/1854124

echo 1 > /sys/kernel/debug/clk/debug_suspend

arch/arm64/boot/dts/qcom/msm8996.dtsi:494:    i2c_7: i2c@75b5000 { /* BLSP2 QUP1 */

arch/arm64/boot/dts/qcom/apq8096pro-g6p.dts:522:&i2c_7 {

 msm8996-pinctrl 1010000.pinctrl: pin GPIO_69 already requested by soc:audio_ext_clk; b
[   33.930822] msm8996-pinctrl 1010000.pinctrl: pin-69 (soc:qcom,ntn_avb) status -22
[   33.941669] msm8996-pinctrl 1010000.pinctrl: could not request pin 69 (GPIO_69) from group gpio69l
[   33.949436] ntn_avb soc:qcom,ntn_avb: Error applying setting, reverse things back

[  137.204758] maxim_serdes 8-0062: Failed to write 0x215 to 0x03
[  137.205143] i2c-msm-v2 75b6000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0
[  137.205187] HJH : maxm_i2c_write_16bit: adapter[MSM-I2C-v2-adapter] i2c write addr[0x47] failed
[  137.205193] maxim_serdes 8-0062: Failed to write 0x42 to 0x94
[  137.260133] maxim_serdes 8-0062: Failed to initialize
[  137.260138] MAX96755-Resume: [max96755_resume] Successful init max96755 reg
[  137.260294] serdes: MAX96755-Resume: [max96755_resume] Set max96755-power-gpio for Hight
[  137.321451] MAX96755-Resume: [max96755_resume] Successful init max96755 reg
[  137.321719] R0: [system_server][137.321760] [05:10:23.766912]  wlan: [710: I:HDD] __wlan_hdd_bus_e
[  137.321881] R0: [kworker/u8:13][137.321924] [05:10:23.767076]  wlan: [3318: E:QDF] get_cds_sched_L
[  137.322022] msm_sensor_power_up:181 failed: ffffffc002633150 ffffffc002636180 0000000000000000 000
[  137.322025] msm_sensor_resume:141 failed rc -22
[  137.322042] dpm_run_callback(): platform_pm_resume+0x0/0x7c returns -14
[  137.322047] PM: Device a0c000.qcom,cci:qcom,camera@0 failed to resume: error -14
[  137.330091] ----ak7739_write_spidmy fialed!-----ret =0,wlen =4
[  137.330599] ak7738 spi0.0: ---Device id = 39

DWC_ETH_QOS_pci_enable_link_status: pcie_link_enable = 1

PM: resume of devices complete after 656.521 msecs

[   66.480007] msm-dwc3 6a00000.ssusb: could not transition HS PHY to L2
[   66.485185] R0: [system_server][66.485218] [05:07:58.713979]  wlan: [713: I:HDD] __wlan_hdd_bus_sd
[   66.485481] serdes: MAX96755-Suspend: [max96755_suspend] Set max96755-power-gpio for LOW
[   66.485644] serdes: MAX96755-Suspend: [max96755_suspend] Set max96755-power-gpio for LOW
[   66.486282] PowerState gpio suspend
[   66.486287] before---Tuner.Enable gpio value is 0 ---
[   66.486293] ---Tuner.Enable gpio value is 1 ---
[   66.486297] before---Telit.Enable gpio value is 0 ---
[   66.486303] ---Telit.Enable gpio value is 1 ---
[   66.486306] before---Ipod.Reset gpio value is 0 ---
[   66.486312] ---Ipod.Reset gpio value is 1 ---
[   66.486315] before---GPSANT.Enable gpio value is 0 ---
[   66.486321] ---GPSANT.Enable gpio value is 1 ---
[   66.486325] before---Core2up.wakeup gpio value is 0 ---
[   66.486331] ---Core2up.wakeup gpio value is 1 ---
[   66.486334] before---TI960.Enable gpio value is 0 ---
[   66.486337] ---TI960.Enable gpio value is 0 ---
[   66.486340] before---TI940.Enable gpio value is 0 ---
[   66.486342] ---TI940.Enable gpio value is 0 ---
[   66.486346] before---dsi.wakeup gpio value is 0 ---
[   66.486348] ---dsi.wakeup gpio value is 0 ---
[   66.486351] before---dsi1.wakeup gpio value is 0 ---
[   66.486354] ---dsi1.wakeup gpio value is 0 ---
[   66.486357] before---1V2_SW_PER_EN gpio value is 0 ---
[   66.486363] ---1V2_SW_PER_EN gpio value is 1 ---
[   66.486367] before---1V1_SW_PER_EN gpio value is 0 ---
[   66.486373] ---1V1_SW_PER_EN gpio value is 0 ---
[   66.486376] before---3V3_SW_PER_EN gpio value is 0 ---
[   66.486381] ---3V3_SW_PER_EN gpio value is 1 ---
[   66.486385] before---1V0_SW_PER_EN gpio value is 0 ---
[   66.486391] ---1V0_SW_PER_EN gpio value is 1 ---
[   66.486394] before---CAM_POWER1 gpio value is 0 ---
[   66.486400] ---CAM_POWER1 gpio value is 1 ---
[   66.486403] before---CAM_POWER2 gpio value is 0 ---
[   66.486409] ---CAM_POWER2 gpio value is 1 ---
[   66.486412] before---CAM_POWER3 gpio value is 0 ---
[   66.486418] ---CAM_POWER3 gpio value is 1 ---
[   66.486421] before---CAM_POWER4 gpio value is 0 ---
[   66.486427] ---CAM_POWER4 gpio value is 1 ---
[   66.486430] before---1V8_SW_PER_EN gpio value is 0 ---
[   66.486433] ---1V8_SW_PER_EN gpio value is 0 ---
[   66.486436] before---usb_hub_en gpio value is 0 ---
[   66.486442] ---usb_hub_en gpio value is 1 ---
[   66.499980] msm-dwc3 7600000.hsusb: could not transition HS PHY to L2
[   66.506479] R0: [system_server][66.506510] [05:07:58.735271]  wlan: [713: I:HDD] __wlan_hdd_bus_sq
[   66.600163] IRQ5 no longer affine to CPU2
[   66.644774]  cache: parent cpu1 should not be sleeping
[   66.646494]  cache: parent cpu2 should not be sleeping
[   66.648459]  cache: parent cpu3 should not be sleeping
[   66.680193] R0: [system_server][66.680272] [05:08:24.615739]  wlan: [713: I:HDD] __wlan_hdd_bus_rq
[   66.709704] PowerState gpio resume
[   66.710434] serdes: MAX96755-Resume: [max96755_resume] Set max96755-power-gpio for Hight
[   66.850506] i2c-msm-v2 75b6000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0
[   66.850553] HJH : maxm_i2c_write_16bit: adapter[MSM-I2C-v2-adapter] i2c write addr[0x48] failed
[   66.850557] maxim_serdes 8-0062: Failed to write 0x0 to 0x8c
[   67.010332] i2c-msm-v2 75b6000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0
[   67.010385] HJH : maxm_i2c_write_16bit: adapter[MSM-I2C-v2-adapter] i2c write addr[0x46] failed
[   67.030244] maxim_serdes 8-0062: Failed to write 0x1ce to 0x5f
[   67.032071] i2c-msm-v2 75b6000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0
[   67.032112] HJH : maxm_i2c_write_16bit: adapter[MSM-I2C-v2-adapter] i2c write addr[0x46] failed
[   67.032116] maxim_serdes 8-0062: Failed to write 0x215 to 0x03
[   67.032329] i2c-msm-v2 75b6000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0
[   67.032369] HJH : maxm_i2c_write_16bit: adapter[MSM-I2C-v2-adapter] i2c write addr[0x46] failed
[   67.032372] maxim_serdes 8-0062: Failed to write 0x42 to 0x92
[   67.032585] i2c-msm-v2 75b6000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0
[   67.032625] HJH : maxm_i2c_write_16bit: adapter[MSM-I2C-v2-adapter] i2c write addr[0x48] failed
[   67.032628] maxim_serdes 8-0062: Failed to write 0x0 to 0x8e
[   67.140488] i2c-msm-v2 75b6000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0
[   67.140535] HJH : maxm_i2c_write_16bit: adapter[MSM-I2C-v2-adapter] i2c write addr[0x47] failed
[   67.140539] maxim_serdes 8-0062: Failed to write 0x1ce to 0x5f
[   67.142336] i2c-msm-v2 75b6000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0
[   67.142376] HJH : maxm_i2c_write_16bit: adapter[MSM-I2C-v2-adapter] i2c write addr[0x47] failed
[   67.142379] maxim_serdes 8-0062: Failed to write 0x215 to 0x03
[   67.142593] i2c-msm-v2 75b6000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0
[   67.142632] HJH : maxm_i2c_write_16bit: adapter[MSM-I2C-v2-adapter] i2c write addr[0x47] failed
[   67.142635] maxim_serdes 8-0062: Failed to write 0x42 to 0x94
[   67.200340] maxim_serdes 8-0062: Failed to initialize
[   67.200345] MAX96755-Resume: [max96755_resume] Successful init max96755 reg
[   67.200508] serdes: MAX96755-Resume: [max96755_resume] Set max96755-power-gpio for Hight
[   67.260237] MAX96755-Resume: [max96755_resume] Successful init max96755 reg
[   67.260420] R0: [system_server][67.260504] [05:08:25.195971]  wlan: [713: I:HDD] __wlan_hdd_bus_re
[   67.260489] R0: [kworker/u8:15][67.260575] [05:08:25.196041]  wlan: [2765: E:QDF] get_cds_sched_cL
[   67.260651] msm_sensor_power_up:181 failed: ffffffc0026aac50 ffffffc0026ad080 0000000000000000 000
[   67.260653] msm_sensor_resume:141 failed rc -22
[   67.260665] dpm_run_callback(): platform_pm_resume+0x0/0x7c returns -14
[   67.260668] PM: Device a0c000.qcom,cci:qcom,camera@0 failed to resume: error -14
[   67.266913] ----ak7739_write_spidmy fialed!-----ret =0,wlen =4
[   67.267101] ak7738 spi0.0: ---Device id = 39

diff --git a/core/res/res/values/config.xml b/core/res/res/values/config.xml
old mode 100644
new mode 100755
index 34f08c4..00ae02b
--- a/core/res/res/values/config.xml
+++ b/core/res/res/values/config.xml
@@ -347,7 +347,7 @@
     </string-array>
 
     <!-- Regex of wired ethernet ifaces -->
-    <string translatable="false" name="config_ethernet_iface_regex">eth\\d</string>
+    <string translatable="false" name="config_ethernet_iface_regex">usb_4G\\d</string>
 
     <!-- If the mobile hotspot feature requires provisioning, a package name and class name
         can be provided to launch a supported application that provisions the devices.

m_pm_resume called name = msm_vidc_v4l2
[   80.760707] platform_pm_resume called name = msm_vidc_v4l2
[   80.760710] platform_pm_resume called name = msm_vidc_v4l2
[   80.760713] platform_pm_resume called name = msm_vidc_v4l2
[   80.760715] platform_pm_resume called name = msm_vidc_v4l2
[   80.760718] platform_pm_resume called name = msm_vidc_v4l2
[   80.760721] platform_pm_resume called name = msm_vidc_v4l2
[   80.760723] platform_pm_resume called name = msm_vidc_v4l2
[   80.760726] platform_pm_resume called name = msm_vidc_v4l2
[   80.760745] msm_sensor_power_up:181 failed: ffffffc002768450 ffffffc002696f00 0000000000000000 000
[   80.760748] msm_sensor_resume:141 failed rc -22
[   80.760749] platform_pm_resume called name = qcom,camera
[   80.760761] dpm_run_callback(): platform_pm_resume+0x0/0x7c returns -14
[   80.760764] PM: Device a0c000.qcom,cci:qcom,camera@0 failed to resume: error -14
[   80.762629] platform_pm_resume called name = qcom,cpr3-mmss-regulator
[   80.762729] platform_pm_resume called name = msm-dwc3
[   80.762734] platform_pm_resume called name = dwc3
[   80.762768] platform_pm_resume called name = kgsl-3d
[   80.762888] PM_DEBUG:AK7739_resume start
[   80.762905] platform_pm_resume called name = apq8096-auto-asoc-snd
[   80.767522] ----ak7739_write_spidmy fialed!-----ret =0,wlen =4
[   80.767725] ak7738 spi0.0: ---Device id = 39
[   80.767727] PM_DEBUG:AK7739_resume completed
[   80.870057] PM: resume of devices complete after 665.393 msecs
[   82.133580] Restarting tasks .

vim ./drivers/media/platform/msm/ais/common/cam_hw_ops.h

cam相关的时钟；

查看gpio的配置：cat sys/kernel/debug/pinctrl/1010000.pinctrl/pinmux-pins 

ts tp位置:

drivers/video/serdes