如何下发AC信号

三个步骤

1、实现AC与AP的互通

2、在AC上配置和WLAN相关的各项参数

3、将AP加入AP组

一、实现AC与AP互通

1、在AC上创建管理vlan，并配置地址放行，还要创建无线的vlan

vlan batch 100 172
interface Vlanif100
    ip address 100.100.100.100 255.255.255.0
interface GigabitEthernet0/0/1
    port link-type trunk
    port trunk allow-pass vlan 2 to 4094

 2、在与AC相连的交换机接口也要配置好各项参数

vlan batch 100 172 192
interface Vlanif100
    ip address 100.100.100.1 255.255.255.0
interface GigabitEthernet0/0/1
    port link-type trunk
    port trunk allow-pass vlan 2 to 4094

3、给在SW1上给AP下发地址

#创建地址池
ip pool apdzc
 gateway-list 192.168.10.254
 network 192.168.10.0 mask 255.255.255.0
 option 43 sub-option 2 ip-address 100.100.100.100

#绑定下发到下发的三层vlan
interface Vlanif192
 ip address 192.168.10.254 255.255.255.0
 dhcp select global

#放行
interface GigabitEthernet0/0/2
 port link-type trunk
 port trunk allow-pass vlan 2 to 4094

 4、在SW2上配置vlan信息

#与AP相连的接口划分vlan
interface Ethernet0/0/22
 port link-type access
 port default vlan 192

#与SW1的放行所有
interface GigabitEthernet0/0/2
 port link-type trunk
 port trunk allow-pass vlan 2 to 4094

5、AP救能获取到地址了

二、在AC配置WLAN的各项参数

1、创建AP的配置

[AC]wlan
[AC-wlan-view]ssid-profile name ssid-zhynet    #模板名称为ssid-zhynet
[AC-wlan-ssid-prof-ssid-zhynet]ssid zhynet    #ssid名称为ssid
[AC-wlan-ssid-prof-ssid-zhynet]quit

[AC-wlan-view]security-profile name sec-zhynet    #安全模板名称为sec-zhynet
[AC-wlan-sec-prof-sec-zhynet]security wpa-wpa2 psk pass-phrase a1234567 aes    #验证方式为wpa-wpa2，密码为a1234567，加密算法为ase
[AC-wlan-sec-prof-sec-zhynet]quit

[AC-wlan-view]vap-profile name vap-zhynet    #vap模板名臣为vap-zhynet
[AC-wlan-vap-prof-vap-zhynet]forward-mode tunnel       #AC模式转发
[AC-wlan-vap-prof-vap-zhynet]service-vlan vlan-id 172    #将接入的用户放入vlan172
[AC-wlan-vap-prof-vap-zhynet]ssid-profile ssid-zhynet    #关联ssid模板
[AC-wlan-vap-prof-vap-zhynet]security-profile sec-zhynet    #关联安全模板

2、创建AP组并加入AP

[AC]wlan 
[AC-wlan-view]ap-group name group-zhynet    #创建AP组，名称为group-zhynet
[AC-wlan-ap-group-group-zhynet]vap-profile vap-zhynet wlan 1 radio all    #所有射频接口都打开2.4G和5G都可以
[AC-wlan-ap-group-group-zhynet]quit

[AC-wlan-view]ap-id 0 ap-mac 00e0-fc22-76d0    #将APmac地址给加入进去
[AC-wlan-ap-0]name ap-zhynet    #名称，方便分辨
[AC-wlan-ap-0]ap-group group-zhynet    #将ap组绑定
#配置完成后要重新启动，输入y确认

3、AC配置和AP对接的vlanif接口

[AC]capwap source interface Vlanif 100

 配置完后就能扫描到了

4、在SW1配置给接入vlan172的地址池

[Huawei]ip pool wxadz
[Huawei-ip-pool-wxadz]gateway-list 172.16.10.254
[Huawei-ip-pool-wxadz]network 172.16.10.0 mask 24
[Huawei-ip-pool-wxadz]qu


interface Vlanif172
 ip address 172.16.10.254 255.255.255.0
 dhcp select global

5、终端成功获取地址

拓扑图