SHT11温湿度测量仿真

最新推荐文章于 2024-10-12 22:54:21 发布

遥*不可及

最新推荐文章于 2024-10-12 22:54:21 发布

阅读量431

点赞数 10

文章标签：嵌入式硬件 c语言

本文链接：https://blog.csdn.net/m0_72530156/article/details/135082695

版权

此文章使通过SHT11模块，AT89C52等芯片设计一个对温湿度测量的仿真实验，文末有本次实验的最终仿真图以及代码。

一、温湿度的测量：

通过SHT11对环境温湿度进行测量，部分代码如下


char s_measure(unsigned char *p_value, unsigned char *p_checksum, unsigned char mode)

{ 
//	enum {TEMP,HUMI};		 
	unsigned error=0;
	unsigned int i;

	s_transstart();                   
	switch(mode)                    
    {	
		case TEMP : error+=s_write_byte(MEASURE_TEMP); break;		   
    	case HUMI : error+=s_write_byte(MEASURE_HUMI); break;		  
    	default     : break; 
	}
	for (i=0;i<65535;i++) if(DATA==0) break; 
	if(DATA) error+=1;                 
	*(p_value) =s_read_byte(ACK);   
	*(p_value+1)=s_read_byte(ACK);    
	*p_checksum =s_read_byte(noACK); 
	return error;					 
}


void calc_sth10(float *p_humidity ,float *p_temperature)
{ 
	const float C1=-4.0;              
	const float C2=+0.0405;           
	const float C3=-0.0000028;       
	const float T1=+0.01;             
	const float T2=+0.00008;         

	float rh=*p_humidity;             
	float t=*p_temperature;           
	float rh_lin;                    
	float rh_true;                    
	float t_C;                       

	t_C=t*0.01 - 40;                 
	rh_lin=C3*rh*rh + C2*rh + C1;    
	rh_true=(t_C-25)*(T1+T2*rh)+rh_lin;   
	if(rh_true>100)rh_true=100;       
	if(rh_true<0.1)rh_true=0.1;       

	*p_temperature=t_C;               
	*p_humidity=rh_true;              
}

接下来就是将参数发送到AT89C52之中去了，部分代码如下：


char s_write_byte(unsigned char value)   
{ 
	unsigned char i,error=0; 
	for (i=0x80;i>0;i/=2)             
	{ 
		if (i&value) DATA=1;          
    	else DATA=0;                        
    	SCK=1;                          
    	_nop_();_nop_();_nop_();         
    	SCK=0;
	}
	DATA=1;                           
	SCK=1;                            
	error=DATA;                       
	_nop_();_nop_();_nop_();
	SCK=0;        
	DATA=1;
	return error;                     
}


char s_read_byte(unsigned char ack)
//----------------------------------------------------------------------------------
{ 
	unsigned char i,val=0;
	DATA=1;                           
	for(i=0x80;i>0;i>>=1)             
	{ 
		SCK=1;                         
    	if(DATA) val=(val|i);        
    	SCK=0;       
	}
	DATA=!ack;                        
	SCK=1;                            
	_nop_();_nop_();_nop_();         
	SCK=0;   
	_nop_();_nop_();_nop_();       
	DATA=1;                           
	return val;
}


void s_transstart(void)
// generates a transmission start 
//       _____         ________
// DATA:      |_______|
//           ___     ___
// SCK : ___|   |___|   |______
{ 
   	DATA=1; SCK=0;                   
   	_nop_();
  	SCK=1;
   	_nop_();
   	DATA=0;
   	_nop_();
  	SCK=0; 
  	 _nop_();_nop_();_nop_();
   	SCK=1;
   	_nop_();
  	DATA=1;     
  	_nop_();
   	SCK=0;     
}

t同时，要将温湿度显示在LED上，所以对LED进行设置，代码如下：

//********************************************************
#define LCD_COMMAND         0      
#define LCD_DATA            1      
#define LCD_CLEAR_SCREEN    0x01      
#define LCD_HOMING          0x02      
void LCD_Write(bit style, unsigned char input)
{
    E=0;
    RS=style;
    RW=0;        _nop_();
    DBPort=input;   _nop_();//×¢ÒâË³Ðò
    E=1;        _nop_();//×¢ÒâË³Ðò
    E=0;        _nop_();
    LCD_Wait(); 
}

//************************************************************
#define LCD_SHOW            0x04   
#define LCD_HIDE            0x00     

#define LCD_CURSOR          0x02    
#define LCD_NO_CURSOR       0x00           

#define LCD_FLASH           0x01    
#define LCD_NO_FLASH        0x00    

void LCD_SetDisplay(unsigned char DisplayMode)
{
    LCD_Write(LCD_COMMAND, 0x08|DisplayMode); 
}

//************************************************************
#define LCD_AC_UP       0x02
#define LCD_AC_DOWN         0x00      

#define LCD_MOVE            0x01     
#define LCD_NO_MOVE         0x00      

void LCD_SetInput(unsigned char InputMode)
{
    LCD_Write(LCD_COMMAND, 0x04|InputMode);
}

//************************************************************
void LCD_Initial()
{
    E=0;
    LCD_Write(LCD_COMMAND,0x38);           
    LCD_Write(LCD_COMMAND,0x38);
    LCD_SetDisplay(LCD_SHOW|LCD_NO_CURSOR);    
    LCD_Write(LCD_COMMAND,LCD_CLEAR_SCREEN);   
    LCD_SetInput(LCD_AC_UP|LCD_NO_MOVE);       ¯
}

//************************
void GotoXY(unsigned char x, unsigned char y)
{
    if(y==0)
        LCD_Write(LCD_COMMAND,0x80|x);
    if(y==1)
        LCD_Write(LCD_COMMAND,0x80|(x-0x40));
}

//
void Print(unsigned char *str)
{
    while(*str!='\0')
    {
        LCD_Write(LCD_DATA,*str);
        str++;
    }
}

温湿度输出代码如下（以温度为例）

TEMP1[0]=temp/1000+'0';     		
if (TEMP1[0]==0x30) TEMP1[0]=0x20;
TEMP1[1]=temp%1000/100+'0';     		
if (TEMP1[1]==0x30 && TEMP1[0]!=0x30) TEMP1[1]=0x20;
TEMP1[2]=temp%100/10+'0';

二、优化调整：

1.由于上述温湿度输出最小精确到个位，为了更加精确的测量，我们将此优化精确到小数点有一位，具体代码如下：

TEMP1[0]=temp/1000+'0';     		
if (TEMP1[0]==0x30) TEMP1[0]=0x20;
TEMP1[1]=temp%1000/100+'0';     	
if (TEMP1[1]==0x30 && TEMP1[0]!=0x30) TEMP1[1]=0x20;
TEMP1[2]=temp%100/10+'0';			
TEMP1[3]=0x2e;						
TEMP1[4]=temp%10+'0';

2.由于时间漂移的存在，我们需要人工调整测量误差，于是我们外置了按钮元件，通过按钮元件来使LED显示屏上温湿度进行0.1的精度调节，部分代码如下

if(P4==0)
			{
			up++;
			}
		}
		for (i=0;i<up;i++)
		{
			temp++;
		}
		
		if(P5==0)	 
		{
			delay(10); 
			if(P5==0)
			{
			down--;
			}
			
		}
		for (i=0;i>down;i--)
		{
			temp--;
		}

三、总结：

通过上述操作，我们可以得到仿真图如下：所有代码如下：（注释太多乱码了，删除太麻烦，将就看一下吧）

#include<reg52.h>
#include <intrins.h>
#include <math.h>    //Keil library 
#include <stdio.h>	 //Keil library

#define uchar unsigned char
sbit P4=P2^4;
sbit P5=P2^5;
sbit P6=P2^6;
sbit P7=P2^7;
typedef union		   //¶¨Òå¹²Í¬ÀàÐÍ
{ unsigned int i;	   //i±íÊ¾²âÁ¿µÃµ½µÄÎÂÊª¶ÈÊý¾Ý£¨int ÐÎÊ½±£´æµÄÊý¾Ý£© 
 float f;			   //f±íÊ¾²âÁ¿µÃµ½µÄÎÂÊª¶ÈÊý¾Ý£¨float ÐÎÊ½±£´æµÄÊý¾Ý£©
} value;


enum {TEMP,HUMI};

sbit DATA = P1^1;
sbit SCK = P1^0;

sbit RS  = P2^0;
sbit RW  = P2^1;
sbit E  = P2^2;
sfr DBPort  = 0x80;     //P0=0x80,P1=0x90,P2=0xA0,P3=0xB0.Êý¾Ý¶Ë¿Ú

/********     1602º¯ÊýÉùÃ÷     ********/
void LCD_Initial();
void GotoXY(unsigned char x, unsigned char y);
void Print(unsigned char *str);
void LCD_Write(bit style, unsigned char input);


/********     SHT11º¯ÊýÉùÃ÷      ********/
void s_connectionreset(void);
char s_measure(unsigned char *p_value, unsigned char *p_checksum, unsigned char mode);
void calc_sth10(float *p_humidity ,float *p_temperature);
//float calc_dewpoint(float h,float t);



/***********************************************************************************************************************************************************/

//SHT11³ÌÐò


#define noACK 0				//¼ÌÐø´«ÊäÊý¾Ý£¬ÓÃÓÚÅÐ¶ÏÊÇ·ñ½áÊøÍ¨Ñ¶
#define ACK   1             //½áÊøÊý¾Ý´«Êä£»
							//µØÖ·  ÃüÁî  ¶Á/Ð´
#define STATUS_REG_W 0x06   //000   0011    0
#define STATUS_REG_R 0x07   //000   0011    1
#define MEASURE_TEMP 0x03   //000   0001    1
#define MEASURE_HUMI 0x05   //000   0010    1
#define RESET        0x1e   //000   1111    0



//Ð´×Ö½Ú³ÌÐò
char s_write_byte(unsigned char value)   
{ 
	unsigned char i,error=0; 
	for (i=0x80;i>0;i/=2)             //shift bit for masking ¸ßÎ»Îª1£¬Ñ»·ÓÒÒÆ
	{ 
		if (i&value) DATA=1;          //ºÍÒª·¢ËÍµÄÊýÏàÓë£¬½á¹ûÎª·¢ËÍµÄÎ»
    	else DATA=0;                        
    	SCK=1;                          
    	_nop_();_nop_();_nop_();        //ÑÓÊ±3us 
    	SCK=0;
	}
	DATA=1;                           //ÊÍ·ÅÊý¾ÝÏß
	SCK=1;                            
	error=DATA;                       //¼ì²éÓ¦´ðÐÅºÅ£¬È·ÈÏÍ¨Ñ¶Õý³£
	_nop_();_nop_();_nop_();
	SCK=0;        
	DATA=1;
	return error;                     //error=1 Í¨Ñ¶´íÎó
}

//¶Á×Ö½Ú³ÌÐò
char s_read_byte(unsigned char ack)
//----------------------------------------------------------------------------------
{ 
	unsigned char i,val=0;
	DATA=1;                           //ÊÍ·ÅÊý¾ÝÏß
	for(i=0x80;i>0;i>>=1)             //¸ßÎ»Îª1£¬Ñ»·ÓÒÒÆ
	{ 
		SCK=1;                         
    	if(DATA) val=(val|i);        //¶ÁÒ»Î»Êý¾ÝÏßµÄÖµ 
    	SCK=0;       
	}
	DATA=!ack;                        //Èç¹ûÊÇÐ£Ñé£¬¶ÁÈ¡Íêºó½áÊøÍ¨Ñ¶£»
	SCK=1;                            
	_nop_();_nop_();_nop_();          //ÑÓÊ±3us 
	SCK=0;   
	_nop_();_nop_();_nop_();       
	DATA=1;                           //ÊÍ·ÅÊý¾ÝÏß
	return val;
}

//Æô¶¯´«Êä
void s_transstart(void)
// generates a transmission start 
//       _____         ________
// DATA:      |_______|
//           ___     ___
// SCK : ___|   |___|   |______
{ 
   	DATA=1; SCK=0;                   //×¼±¸
   	_nop_();
  	SCK=1;
   	_nop_();
   	DATA=0;
   	_nop_();
  	SCK=0; 
  	 _nop_();_nop_();_nop_();
   	SCK=1;
   	_nop_();
  	DATA=1;     
  	_nop_();
   	SCK=0;     
}


//Á¬½Ó¸´Î»
void s_connectionreset(void)
// communication reset: DATA-line=1 and at least 9 SCK cycles followed by transstart
//       _____________________________________________________         ________
// DATA:                                                      |_______|
//          _    _    _    _    _    _    _    _    _        ___     ___
// SCK : __| |__| |__| |__| |__| |__| |__| |__| |__| |______|   |___|   |______
{ 
	unsigned char i; 
	DATA=1; SCK=0;                    //×¼±¸
	for(i=0;i<9;i++)                  //DATA±£³Ö¸ß£¬SCKÊ±ÖÓ´¥·¢9´Î£¬·¢ËÍÆô¶¯´«Êä£¬Í¨Ñ¸¼´¸´Î»
	{ 
		SCK=1;
    	SCK=0;
	}
	s_transstart();                   //Æô¶¯´«Êä
}


//Èí¸´Î»³ÌÐò
char s_softreset(void)
// resets the sensor by a softreset 
{ 
	unsigned char error=0; 
	s_connectionreset();              //Æô¶¯Á¬½Ó¸´Î»
	error+=s_write_byte(RESET);       //·¢ËÍ¸´Î»ÃüÁî
	return error;                     //error=1 Í¨Ñ¶´íÎó
}


/*
//¶Á×´Ì¬¼Ä´æÆ÷
char s_read_statusreg(unsigned char *p_value, unsigned char *p_checksum)
//----------------------------------------------------------------------------------
// reads the status register with checksum (8-bit)
{ 
	unsigned char error=0;
	s_transstart();                   //transmission start
	error=s_write_byte(STATUS_REG_R); //send command to sensor
	*p_value=s_read_byte(ACK);        //read status register (8-bit)
	*p_checksum=s_read_byte(noACK);   //read checksum (8-bit) 
	return error;                     //error=1 in case of no response form the sensor
}

//Ð´×´Ì¬¼Ä´æÆ÷
char s_write_statusreg(unsigned char *p_value)
// writes the status register with checksum (8-bit)
{ 
	unsigned char error=0;
	s_transstart();                   //transmission start
	error+=s_write_byte(STATUS_REG_W);//send command to sensor
	error+=s_write_byte(*p_value);    //send value of status register
	return error;                     //error>=1 in case of no response form the sensor
}															*/			   

           
//ÎÂÊª¶È²âÁ¿
char s_measure(unsigned char *p_value, unsigned char *p_checksum, unsigned char mode)
// ½øÐÐÎÂ¶È»òÕßÊª¶È×ª»»£¬ÓÉ²ÎÊýmode¾ö¶¨×ª»»ÄÚÈÝ£»
{ 
//	enum {TEMP,HUMI};		 //ÒÑ¾ÔÚÍ·ÎÄ¼þÖÐ¶¨Òå
	unsigned error=0;
	unsigned int i;

	s_transstart();                   //Æô¶¯´«Êä
	switch(mode)                     //Ñ¡Ôñ·¢ËÍÃüÁî
    {	
		case TEMP : error+=s_write_byte(MEASURE_TEMP); break;		   //²âÁ¿ÎÂ¶È
    	case HUMI : error+=s_write_byte(MEASURE_HUMI); break;		   //²âÁ¿Êª¶È
    	default     : break; 
	}
	for (i=0;i<65535;i++) if(DATA==0) break; //µÈ´ý²âÁ¿½áÊø
	if(DATA) error+=1;                // Èç¹û³¤Ê±¼äÊý¾ÝÏßÃ»ÓÐÀµÍ£¬ËµÃ÷²âÁ¿´íÎó 
	*(p_value) =s_read_byte(ACK);    //¶ÁµÚÒ»¸ö×Ö½Ú£¬¸ß×Ö½Ú (MSB)
	*(p_value+1)=s_read_byte(ACK);    //¶ÁµÚ¶þ¸ö×Ö½Ú£¬µÍ×Ö½Ú (LSB)
	*p_checksum =s_read_byte(noACK); //read CRCÐ£ÑéÂë
	return error;					 // error=1 Í¨Ñ¶´íÎó
}

//ÎÂÊª¶ÈÖµ±ê¶È±ä»»¼°ÎÂ¶È²¹³¥
void calc_sth10(float *p_humidity ,float *p_temperature)
{ 
	const float C1=-4.0;              // 12Î»Êª¶È¾«¶È ÐÞÕý¹«Ê½
	const float C2=+0.0405;           // 12Î»Êª¶È¾«¶È ÐÞÕý¹«Ê½
	const float C3=-0.0000028;        // 12Î»Êª¶È¾«¶È ÐÞÕý¹«Ê½
	const float T1=+0.01;             // 14Î»ÎÂ¶È¾«¶È 5VÌõ¼þ  ÐÞÕý¹«Ê½
	const float T2=+0.00008;          // 14Î»ÎÂ¶È¾«¶È 5VÌõ¼þ  ÐÞÕý¹«Ê½

	float rh=*p_humidity;             // rh:      12Î» Êª¶È 
	float t=*p_temperature;           // t:       14Î» ÎÂ¶È
	float rh_lin;                     // rh_lin: Êª¶È linearÖµ
	float rh_true;                    // rh_true: Êª¶È tureÖµ
	float t_C;                        // t_C   : ÎÂ¶È ¡æ

	t_C=t*0.01 - 40;                  //²¹³¥ÎÂ¶È
	rh_lin=C3*rh*rh + C2*rh + C1;     //Ïà¶ÔÊª¶È·ÇÏßÐÔ²¹³¥
	rh_true=(t_C-25)*(T1+T2*rh)+rh_lin;   //Ïà¶ÔÊª¶È¶ÔÓÚÎÂ¶ÈÒÀÀµÐÔ²¹³¥
	if(rh_true>100)rh_true=100;       //Êª¶È×î´óÐÞÕý
	if(rh_true<0.1)rh_true=0.1;       //Êª¶È×îÐ¡ÐÞÕý

	*p_temperature=t_C;               //·µ»ØÎÂ¶È½á¹û
	*p_humidity=rh_true;              //·µ»ØÊª¶È½á¹û
}

//´ÓÏà¶ÔÎÂ¶ÈºÍÊª¶È¼ÆËãÂ¶µã
/*float calc_dewpoint(float h,float t)
{
	float logEx,dew_point;
	logEx=0.66077+7.5*t/(237.3+t)+(log10(h)-2);
	dew_point = (logEx - 0.66077)*237.3/(0.66077+7.5-logEx);
	return dew_point;
}						   					*/

/***********************************************************************************************************************************************************/
//1602³ÌÐò


//ÄÚ²¿µÈ´ýº¯Êý**************************************************************
unsigned char LCD_Wait(void)
{
    RS=0;
    RW=1;    _nop_();
    E=1;    _nop_();           
    E=0;
    return DBPort;  
}
//ÏòLCDÐ´ÈëÃüÁî»òÊý¾Ý********************************************************
#define LCD_COMMAND         0      // Command
#define LCD_DATA            1      // Data
#define LCD_CLEAR_SCREEN    0x01      // ÇåÆÁ
#define LCD_HOMING          0x02      // ¹â±ê·µ»ØÔµã
void LCD_Write(bit style, unsigned char input)
{
    E=0;
    RS=style;
    RW=0;        _nop_();
    DBPort=input;   _nop_();//×¢ÒâË³Ðò
    E=1;        _nop_();//×¢ÒâË³Ðò
    E=0;        _nop_();
    LCD_Wait(); 
}

//ÉèÖÃÏÔÊ¾Ä£Ê½************************************************************
#define LCD_SHOW            0x04    //ÏÔÊ¾¿ª
#define LCD_HIDE            0x00    //ÏÔÊ¾¹Ø 

#define LCD_CURSOR          0x02    //ÏÔÊ¾¹â±ê
#define LCD_NO_CURSOR       0x00    //ÎÞ¹â±ê        

#define LCD_FLASH           0x01    //¹â±êÉÁ¶¯
#define LCD_NO_FLASH        0x00    //¹â±ê²»ÉÁ¶¯

void LCD_SetDisplay(unsigned char DisplayMode)
{
    LCD_Write(LCD_COMMAND, 0x08|DisplayMode); 
}

//ÉèÖÃÊäÈëÄ£Ê½************************************************************
#define LCD_AC_UP       0x02
#define LCD_AC_DOWN         0x00      // default

#define LCD_MOVE            0x01      // »Ãæ¿ÉÆ½ÒÆ
#define LCD_NO_MOVE         0x00      //default

void LCD_SetInput(unsigned char InputMode)
{
    LCD_Write(LCD_COMMAND, 0x04|InputMode);
}

//³õÊ¼»¯LCD************************************************************
void LCD_Initial()
{
    E=0;
    LCD_Write(LCD_COMMAND,0x38);           //8Î»Êý¾Ý¶Ë¿Ú,2ÐÐÏÔÊ¾,5*7µãÕó
    LCD_Write(LCD_COMMAND,0x38);
    LCD_SetDisplay(LCD_SHOW|LCD_NO_CURSOR);    //¿ªÆôÏÔÊ¾, ÎÞ¹â±ê
    LCD_Write(LCD_COMMAND,LCD_CLEAR_SCREEN);   //ÇåÆÁ
    LCD_SetInput(LCD_AC_UP|LCD_NO_MOVE);       //ACµÝÔö, »Ãæ²»¶¯
}

//Òº¾§×Ö·ûÊäÈëµÄÎ»ÖÃ************************
void GotoXY(unsigned char x, unsigned char y)
{
    if(y==0)
        LCD_Write(LCD_COMMAND,0x80|x);
    if(y==1)
        LCD_Write(LCD_COMMAND,0x80|(x-0x40));
}

//½«×Ö·ûÊä³öµ½Òº¾§ÏÔÊ¾
void Print(unsigned char *str)
{
    while(*str!='\0')
    {
        LCD_Write(LCD_DATA,*str);
        str++;
    }
}



//ÑÓÊ±º¯Êý
void delay(int z)		//zÎªºÁÃëÊý
{
	int x,y;
	for(x=z;x>0;x--)
		for(y=125;y>0;y--);
}

/***********************************************************************************************************************************************************/
//Ö÷º¯Êý

void main()
{ 
	unsigned int temp,humi;
	value humi_val,temp_val;		//¶¨ÒåÁ½¸ö¹²Í¬Ìå£¬Ò»¸öÓÃÓÚÊª¶È£¬Ò»¸öÓÃÓÚÎÂ¶È
//	float dew_point;			    //ÓÃÓÚ¼ÇÂ¼Â¶µãÖµ
	unsigned char error;		    //ÓÃÓÚ¼ìÑéÊÇ·ñ³öÏÖ´íÎó
	unsigned char checksum;			//CRC			 
	uchar TEMP1[7];				 	//ÓÃÓÚ¼ÇÂ¼ÎÂ¶È
	uchar HUMI1[6];				 	//ÓÃÓÚ¼ÇÂ¼Êª¶È
	int up=0,down=0,ups=0,downs=0;
	int i;				 
	LCD_Initial();					   //³õÊ¼»¯Òº¾§		  
   	GotoXY(0,0);					   //Ñ¡ÔñÎÂ¶ÈÏÔÊ¾Î»ÖÃ
   	Print("Temp:      C");			   //5¸ñ¿Õ¸ñ
 	GotoXY(0,1);					   //Ñ¡ÔñÊª¶ÈÏÔÊ¾Î»ÖÃ
   	Print("Humi:     %RH");			   //5¸ñ¿Õ¸ñ
	s_connectionreset();			   //Æô¶¯Á¬½Ó¸´Î»
	while(1)
	{
		error=0;					   //³õÊ¼»¯error=0£¬¼´Ã»ÓÐ´íÎó
		error+=s_measure((unsigned char*)&temp_val.i,&checksum,TEMP); //ÎÂ¶È²âÁ¿
		error+=s_measure((unsigned char*)&humi_val.i,&checksum,HUMI); //Êª¶È²âÁ¿
    	if(error!=0) s_connectionreset();                 Èç¹û·¢Éú´íÎó£¬ÏµÍ³¸´Î»
    	else
    	{ 
			humi_val.f=(float)humi_val.i;                   //×ª»»Îª¸¡µãÊý
     		temp_val.f=(float)temp_val.i;                   //×ª»»Îª¸¡µãÊý
     		calc_sth10(&humi_val.f,&temp_val.f);            //ÐÞÕýÏà¶ÔÊª¶È¼°ÎÂ¶È
//   		dew_point=calc_dewpoint(humi_val.f,temp_val.f); //¼ÆËãe dew_point
   			temp=temp_val.f*10;
     		humi=humi_val.f*10;
     		GotoXY(5,0);						//ÉèÖÃÎÂ¶ÈÏÔÊ¾Î»ÖÃ
				if(P4==0)	  //
		{
			delay(10); //
			if(P4==0)
			{
			up++;
			}
		}
		for (i=0;i<up;i++)
		{
			temp++;
		}
		
		if(P5==0)	  //?P1.0??,????????,???if
		{
			delay(10); 
			if(P5==0)
			{
			down--;
			}
			
		}
		for (i=0;i>down;i--)
		{
			temp--;
		}   //¿ØÖÆÎÂ¶ÈÒÔ0.1µÄ¸Ä±äÁ¿±ä»¯  
		
		if(P6==0)	  //
		{
			delay(10); //
			if(P6==0)
			{
			ups++;
			}
		}
		for (i=0;i<ups;i++)
		{
			humi++;
		}
		
		if(P7==0)	  //?P1.0??,????????,???if
		{
			delay(10); 
			if(P7==0)
			{
			downs--;
			}
			
		}
		for (i=0;i>downs;i--)
		{
			humi--;
		}
      		TEMP1[0]=temp/1000+'0';     		//ÎÂ¶È°ÙÎ» 
			if (TEMP1[0]==0x30) TEMP1[0]=0x20;
			TEMP1[1]=temp%1000/100+'0';     	//ÎÂ¶ÈÊ®Î»	
			if (TEMP1[1]==0x30 && TEMP1[0]!=0x30) TEMP1[1]=0x20;
   			TEMP1[2]=temp%100/10+'0';			//ÎÂ¶È¸öÎ»
      		TEMP1[3]=0x2e;						//Ð¡Êýµã
   			TEMP1[4]=temp%10+'0';				//ÎÂ¶ÈÐ¡ÊýµãºóµÚÒ»Î»		
			TEMP1[5]=0xdf;						//ÏÔÊ¾ÎÂ¶È·ûºÅ¡æ
			Print(TEMP1);						//Êä³öÎÂ¶È	   	  
	    	GotoXY(5,1);						//ÉèÖÃÊª¶ÈÏÔÊ¾Î»ÖÃ					 
			HUMI1[0]=humi/1000+'0';     		//Êª¶È°ÙÎ»
      		if (HUMI1[0]==0x30) HUMI1[0]=0x20;
			HUMI1[1]=humi%1000/100+'0';     	//Êª¶ÈÊ®Î»	
   			if (HUMI1[1]==0x30 && HUMI1[0]!=0x30) HUMI1[1]=0X20;  
			HUMI1[2]=humi%100/10+'0';			//Êª¶È¸öÎ»
      		HUMI1[3]=0x2E;						//Ð¡Êýµã
   			HUMI1[4]=humi%10+'0';				//Êª¶ÈÐ¡ÊýµãºóµÚÒ»Î»	
			Print(HUMI1);						//Êä³öÊª¶È	   
    	}  
		delay(800);                             //µÈ´ý×ã¹»³¤µÄÊ±¼ä£¬ÒÔ½øÐÐÏÂÒ»´Î×ª»»                    
	}
}

以上就是本次仿真的所有内容，谢谢观看