vmware克隆报错Job for network.service failed because the control process exited with error code

• vmware克隆报错Job for network.service failed because the control process
  exited with error code

1.问题描述：克隆启动虚拟机以后，ifconfig后连ip地址都没了；

[root@centos7 ~]# ifconfig
lo: flags=73<UP,LOOPBACK,RUNNING>  mtu 65536
        inet 127.0.0.1  netmask 255.0.0.0
        inet6 ::1  prefixlen 128  scopeid 0x10<host>
        loop  txqueuelen 1000  (Local Loopback)
        RX packets 0  bytes 0 (0.0 B)
        RX errors 0  dropped 0  overruns 0  frame 0
        TX packets 0  bytes 0 (0.0 B)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0

virbr0: flags=4099<UP,BROADCAST,MULTICAST>  mtu 1500
        inet 192.168.122.1  netmask 255.255.255.0  broadcast 192.168.122.255
        ether 52:54:00:8e:69:8c  txqueuelen 1000  (Ethernet)
        RX packets 0  bytes 0 (0.0 B)
        RX errors 0  dropped 0  overruns 0  frame 0
        TX packets 0  bytes 0 (0.0 B)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0

重启网卡

[root@centos7 ~]# systemctl restart network
Job for network.service failed because the control process exited with error code. See "systemctl status network.service" and "journalctl -xe" for details.

2.解决方案;网上有很多说法，大多都是重新vim /etc/sysconfig/network-scripts/ifcfg-ens33 配置静态ip的, 也有说是mac地址问题，这些原因一一测试都排除了，其实是网卡不工作了，最后只有一种方法管用，关闭NetworkManager

临时关闭
systemctl stop NetworkManager
永久关闭
systemctl disable NetworkManager
重启
systemctl restart network

再次查看
[root@centos7 network-scripts]# ifconfig
ens33: flags=4163<UP,BROADCAST,RUNNING,MULTICAST>  mtu 1500
        inet 192.168.10.101  netmask 255.255.255.0  broadcast 192.168.10.255
        inet6 fe80::20c:29ff:fec7:5224  prefixlen 64  scopeid 0x20<link>
        ether 00:0c:29:c7:52:24  txqueuelen 1000  (Ethernet)
        RX packets 15  bytes 1114 (1.0 KiB)
        RX errors 0  dropped 0  overruns 0  frame 0
        TX packets 36  bytes 4794 (4.6 KiB)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0

lo: flags=73<UP,LOOPBACK,RUNNING>  mtu 65536
        inet 127.0.0.1  netmask 255.0.0.0
        inet6 ::1  prefixlen 128  scopeid 0x10<host>
        loop  txqueuelen 1000  (Local Loopback)
        RX packets 0  bytes 0 (0.0 B)
        RX errors 0  dropped 0  overruns 0  frame 0
        TX packets 0  bytes 0 (0.0 B)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0

virbr0: flags=4099<UP,BROADCAST,MULTICAST>  mtu 1500
        inet 192.168.122.1  netmask 255.255.255.0  broadcast 192.168.122.255
        ether 52:54:00:8e:69:8c  txqueuelen 1000  (Ethernet)
        RX packets 0  bytes 0 (0.0 B)
        RX errors 0  dropped 0  overruns 0  frame 0
        TX packets 0  bytes 0 (0.0 B)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0

3.原因
在CentOS系统上，目前有NetworkManager和network两种网络管理工具。如果两种都配置会引起冲突。由于一般我们都是使用 network 配置静态ip，可能是克隆导致NetWorkManager自动配置，具体原因不清楚，发生了冲突，所以把它禁用掉就好了。

4.感谢阅读，如果能帮到您，是我的荣幸