1. Introduction
The Valgrind tool suite provides a number of debugging and profiling tools that help you make your programs faster and more correct. The most popular of these tools is called Memcheck. It can detect many memory-related errors that are common in C and C++ programs and that can lead to crashes and unpredictable behaviour.
The rest of this guide gives the minimum information you need to start detecting memory errors in your program with Memcheck. For full documentation of Memcheck and the other tools, please read the User Manual.
2. Preparing your program
Compile your program with -g to include debugging information so that Memcheck’s error messages include exact line numbers. Using -O0 is also a good idea, if you can tolerate the slowdown. With -O1 line numbers in error messages can be inaccurate, although generally speaking running Memcheck on code compiled at -O1 works fairly well, and the speed improvement compared to running -O0 is quite significant. Use of -O2 and above is not recommended as Memcheck occasionally reports uninitialised-value errors which don’t really exist.
3. Running your program under Memcheck
If you normally run your program like this:
myprog arg1 arg2
Use this command line:
valgrind --leak-check=yes myprog arg1 arg2
Memcheck is the default tool. The --leak-check option turns on the detailed memory leak detector.
Your program will run much slower (eg. 20 to 30 times) than normal, and use a lot more memory. Memcheck will issue messages about memory errors and leaks that it detects.
4. Interpreting Memcheck’s output
Here’s an example C program, in a file called a.c, with a memory error and a memory leak.
#include <stdlib.h>
void f(void)
{
int* x = malloc(10 * sizeof(int));
x[10] = 0; // problem 1: heap block overrun
} // problem 2: memory leak -- x not freed
int main(void)
{
f();
return 0;
}
Most error messages look like the following, which describes problem 1, the heap block overrun:
==19182== Invalid write of size 4
==19182== at 0x804838F: f (example.c:6)
==19182== by 0x80483AB: main (example.c:11)
==19182== Address 0x1BA45050 is 0 bytes after a block of size 40 alloc'd
==19182== at 0x1B8FF5CD: malloc (vg_replace_malloc.c:130)
==19182== by 0x8048385: f (example.c:5)
==19182== by 0x80483AB: main (example.c:11)
Things to notice:
There is a lot of information in each error message; read it carefully.
The 19182 is the process ID; it's usually unimportant.
The first line ("Invalid write...") tells you what kind of error it is.
Here, the program wrote to some memory it should not have due to a heap block overrun.
Below the first line is a stack trace telling you where the problem occurred.
Stack traces can get quite large, and be confusing, especially if you are using the C++ STL.
Reading them from the bottom up can help. If the stack trace is not big enough,
use the --num-callers option to make it bigger.
The code addresses (eg. 0x804838F) are usually unimportant,
but occasionally crucial for tracking down weirder bugs.
Some error messages have a second component which describes the memory address involved.
This one shows that the written memory is just past the end of a block allocated with malloc() on
line 5 of example.c.
It’s worth fixing errors in the order they are reported, as later errors can be caused by earlier errors. Failing to do this is a common cause of difficulty with Memcheck.
Memory leak messages look like this:
==19182== 40 bytes in 1 blocks are definitely lost in loss record 1 of 1
==19182== at 0x1B8FF5CD: malloc (vg_replace_malloc.c:130)
==19182== by 0x8048385: f (a.c:5)
==19182== by 0x80483AB: main (a.c:11)
The stack trace tells you where the leaked memory was allocated. Memcheck cannot tell you why the memory leaked, unfortunately. (Ignore the “vg_replace_malloc.c”, that’s an implementation detail.)
There are several kinds of leaks; the two most important categories are:
-
“definitely lost”: your program is leaking memory – fix it!
-
“probably lost”: your program is leaking memory, unless you’re doing funny things with pointers (such as moving them to point to the middle of a heap block).
Memcheck also reports uses of uninitialised values, most commonly with the message “Conditional jump or move depends on uninitialised value(s)”. It can be difficult to determine the root cause of these errors. Try using the --track-origins=yes to get extra information. This makes Memcheck run slower, but the extra information you get often saves a lot of time figuring out where the uninitialised values are coming from.
If you don’t understand an error message, please consult Explanation of error messages from Memcheck in the Valgrind User Manual which has examples of all the error messages Memcheck produces.