H3C数据中心交换机无法堆叠问题

金华移动遇到2台H3C S6805-54HF交换机，堆叠起不来的情况，硬件平台和软件都是一样的，排除堆叠线缆兼容性问题，最后发现是交换机的基础配置不一致造成。
按照官方的堆叠配置做完之后，交换机给出的报错。并且堆叠起不来。
%Jan 1 00:57:01:265 2001 H3C DRVPLAT/4/DrvDebug:
The port HG2/0/26 can’t receive irf pkt, please check.
报错只有这句话，有点懵，设备重启后终于给出具体原因如下：
System is starting…
The Switch-routing-mode configurations should be the same on devices in one IRF.Please check them on the neighbor device connected to IRF-port 2
大概意思就是2台做堆叠的设备的基础配置不一致造成的。

        Board checking.....................LSW148TG6HB
        SDRAM fast selftest........................OK!
        Flash fast selftest........................OK!
        CPLD selftest..............................OK!
        Switch chip selftest.......................OK!
        PHY selftest...............................OK!
        Please check leds....................FINISHED!

Cryptographic algorithms tests passed.
Line aux1 is available.
Press ENTER to get started.
首先看第一台设备的硬件资源配置情况
dis hardware-resource
Switch-mode resource(switch-mode), all supported modes:
NORMAL MAC table:96K, ARP and ND tables:80K, routing table:160K
MAC MAC table:288K, ARP and ND tables:16K, routing table:32K
ROUTING MAC table:32K, ARP and ND tables:16K, routing table:324K
ARP MAC table:32K, ARP and ND tables:272K, routing table:32K
DUAL-STACK MAC table:32K, ARP and ND tables:16K, routing:v4-87K,v6-86K
EM MAC table:32K, ARP and ND tables:16K, routing table:32K

Default Current Next
NORMAL NORMAL NORMAL

Routing-mode resource(routing-mode), all supported modes:
ipv6-64 ipv6-64 supported
ipv6-128 ipv6-128 supported

Default Current Next
ipv6-64 ipv6-64 ipv6-64

Vxlan resource(vxlan), all supported modes:
l2gw L2 gateway–underlay/overlay 64K/0K
l3gw L3 gateway–underlay/overlay 24K/40K

Default Current Next
dis hardware-resource routing-mode

Routing-mode resource(routing-mode), all supported modes:
ipv6-64 ipv6-64 supported
ipv6-128 ipv6-128 supported

Default Current Next
ipv6-64 ipv6-64 ipv6-64
修改下资源配置
sys
[H3C]hardware-resource routing-mode ipv6-128
Do you want to change the specified hardware resource working mode? [Y/N]:
y
The hardware resource working mode is changed, please save the configuration and reboot the

system to make it effective.
[H3C]hardware-resource switch-mode ROUTING
Do you want to change the specified hardware resource working mode? [Y/N]:y
The hardware resource working mode is changed, please save the configuration and reboot the

system to make it effective.
[H3C]
quit
save
The current configuration will be written to the device. Are you sure? [Y/N]:
y%

Please input the file name(*.cfg)[flash:/startup.cfg]
(To leave the existing filename unchanged, press the enter key):
Validating file. Please wait…
The startup.cfg file already exists.
Compared with the startup.cfg file, The current configuration adds 2 commands and deletes 0

commands.
If you want to see the configuration differences, please cancel this operation, and then use

the display diff command to show the details.
If you continue the save operation, the file will be overwritten.
Are you sure you want to continue the save operation? [Y/N]:
Before pressing ENTER you must choose ‘YES’ or ‘NO’[Y/N]:y
Saving the current configuration to the file. Please wait…
Saved the current configuration to mainboard device successfully.
reboot
保存配置，重启生效；另外一台也做相同配置。
需要堆叠设备除了硬件平台，软件需要一致以外，还有他们的的路由模式，交换模式，vxlan模式中的资源分配配置必须一致，堆叠才能起来