华为与H3C
华为与H3C技术。
林向阳的BLOG
我要成功,一言既出,万山无阻。
展开
-
H3C校园网双出口配置“命令详细”
一、基本配置pc1配置<h3c>system-view[h3c]sysname pc1[h3c]int g0/0[pc1-GigabitEthernet0/0]ip add 192.168.2.100 255.255.255.0[pc1-GigabitEthernet0/0]undo sh[pc1-GigabitEthernet0/0]quit[pc1]ip route-static 0.0.0.0 0.0.0.0 192.168.2.1[pc...原创 2020-06-24 20:06:21 · 1465 阅读 · 0 评论 -
华为USG6000V双机热备HRRP
1、 配置IP省略2、 区域划分[fw1]firewall zone trust[fw1-zone-trust]undo add int g0/0/0[fw1-zone-trust]add int g1/0/2[fw1]firewall zone dmz[fw1-zone-dmz]add int g0/0/0[fw1-zone-dmz]q[fw1]firewall zone untrust[fw1-zone-untrust]add int g1/0/0[fw1-zone-u.原创 2020-06-21 21:25:11 · 1336 阅读 · 0 评论 -
ospf、mstp、lacp、nat技术、模拟联通电信访通过bgp连接访问外网服务器!!!步骤详细
案例实验:防火墙配置:Lacp[fhq1]lacp priority 1000[fhq1]int Eth-Trunk 12[fhq1-Eth-Trunk12]mode lacp-static[fhq1-Eth-Trunk12]load-balance dst-mac[fhq1-Eth-Trunk12]trunkport g0/0/1Info: This operation may take a few seconds. Please wait for a mome...原创 2020-06-20 11:12:17 · 865 阅读 · 0 评论 -
华为USG6000V防火墙telnet+安全策略!!!
实验拓扑实验要求:实现在内部的clound1上可以telnet、ssh以及web方式访问防火墙实现内部的pc1可以访问外部的pc2,而pc3不可以访问实现外部的pc2可以访问dmz中的服务器(ftp,http以及icmp)一、配置防火墙允许telnet1)配置接口ip[USG6000V1]int g0/0/0[USG6000V1-GigabitEthernet0/0/0]ip add 192.168.0.1 24[USG6000V1]int g1/0...原创 2020-06-16 10:19:02 · 4752 阅读 · 0 评论 -
二层交换hybrid接口
实验实施:hybrid接口实验准备:配置PC,IP地址。[sw 1]vlan batch 1 2 3 10在连接pc1的端口设置hybrid接口[sw 1]int GigabitEthernet 0/0/1[sw 1-GigabitEthernet0/0/1]port link-type hybrid[sw 1-GigabitEthernet0/0/1]port hybrid pvid v 1[sw 1-GigabitEthernet0/0/1]port hybri...原创 2020-06-14 11:18:41 · 733 阅读 · 0 评论 -
华为综合实验2!!!acl,ospf,rip,路由充分发,静态nat,pat!!!
八、配置acl说明:注1:一个接口的同一个方向,只能调用一个acl注2:一个acl里面可以有多个rule 规则,从上往下依次执行注3:数据包一旦被某rule匹配,就不再继续向下匹配注4: 用来做数据包访问控制时,默认隐含放过所有(华为设备)1.标准acl 列表号为2000-2999<huawei>sys[huawei]acl 2000[Huawei-acl-basic-2000]rule 0 [permit|deny] source 网段/主机 反掩码...原创 2020-06-11 10:02:55 · 1096 阅读 · 0 评论 -
华为综合实验1!!!链路聚合,VLAN,虚接口,默认路由,静态路由!!!
pc连接交换机的口味access模式,在access模式下分配VLAN2层交换机连接三层交换机的两个端口为trunk(中继)中继默认只允许VLAN1通过,需在设置允许所有VLAN通过。三层交换机连接路由器的端口为虚借口,用单独VLAN设置对应的路由器的网段IP一、创建链路聚合(通过静态lacp协商主动端和被动端)1.配置lacp优先级[sw1]lacp priority 10002.创建链路聚合逻辑端口,名称为eth-trunk idsw1]int E...原创 2020-06-10 10:13:55 · 2293 阅读 · 0 评论 -
ensp远程telnet和console连接
云配置如下:路由器配置<Huawei>system-viewEnter system view, return user view with Ctrl+Z.[Huawei]undo info-center enInfo: Information center is disabled.[Huawei]int g0/0/0[Huawei-GigabitEthernet0/0/0]ip add 192.168.1.1 24#启用telnet远程登录[...原创 2020-06-10 10:08:09 · 1824 阅读 · 0 评论