nRF52832/52840怎么将NFC引脚配置成通用IO（P0.09,P0.10）

对于Nordic SDK的程序架构来说，引脚的NFC功能和Reset功能主要是在system_nrf52.c，跳转进main函数前执行SystemInit进行初始化的。代码如下

void SystemInit(void)
{
	......

    /* Configure NFCT pins as GPIOs if NFCT is not to be used in your code. If CONFIG_NFCT_PINS_AS_GPIOS is not defined,
       two GPIOs (see Product Specification to see which ones) will be reserved for NFC and will not be available as
       normal GPIOs. */
    #if defined (CONFIG_NFCT_PINS_AS_GPIOS)
        if ((NRF_UICR->NFCPINS & UICR_NFCPINS_PROTECT_Msk) == (UICR_NFCPINS_PROTECT_NFC << UICR_NFCPINS_PROTECT_Pos)){
            NRF_NVMC->CONFIG = NVMC_CONFIG_WEN_Wen << NVMC_CONFIG_WEN_Pos;
            while (NRF_NVMC->READY == NVMC_READY_READY_Busy){}
            NRF_UICR->NFCPINS &= ~UICR_NFCPINS_PROTECT_Msk;
            while (NRF_NVMC->READY == NVMC_READY_READY_Busy){}
            NRF_NVMC->CONFIG = NVMC_CONFIG_WEN_Ren << NVMC_CONFIG_WEN_Pos;
            while (NRF_NVMC->READY == NVMC_READY_READY_Busy){}
            NVIC_SystemReset();
        }
    #endif

    /* Configure GPIO pads as pPin Reset pin if Pin Reset capabilities desired. If CONFIG_GPIO_AS_PINRESET is not
      defined, pin reset will not be available. One GPIO (see Product Specification to see which one) will then be
      reserved for PinReset and not available as normal GPIO. */
    #if defined (CONFIG_GPIO_AS_PINRESET)
        if (((NRF_UICR->PSELRESET[0] & UICR_PSELRESET_CONNECT_Msk) != (UICR_PSELRESET_CONNECT_Connected << UICR_PSELRESET_CONNECT_Pos)) ||
            ((NRF_UICR->PSELRESET[1] & UICR_PSELRESET_CONNECT_Msk) != (UICR_PSELRESET_CONNECT_Connected << UICR_PSELRESET_CONNECT_Pos))){
            NRF_NVMC->CONFIG = NVMC_CONFIG_WEN_Wen << NVMC_CONFIG_WEN_Pos;
            while (NRF_NVMC->READY == NVMC_READY_READY_Busy){}
            NRF_UICR->PSELRESET[0] = 21;
            while (NRF_NVMC->READY == NVMC_READY_READY_Busy){}
            NRF_UICR->PSELRESET[1] = 21;
            while (NRF_NVMC->READY == NVMC_READY_READY_Busy){}
            NRF_NVMC->CONFIG = NVMC_CONFIG_WEN_Ren << NVMC_CONFIG_WEN_Pos;
            while (NRF_NVMC->READY == NVMC_READY_READY_Busy){}
            NVIC_SystemReset();
        }
    #endif

    SystemCoreClockUpdate();
}

由代码可以看出，特色功能的IO配置通用的配置方法是需要在编译选项里的全局变量进行设置的，如下：

话外，有些朋友曾经遇到过调试APP部分是OK，IO正常运行，而烧录三合一程序的时候就失效了。这种情况需要核对一下BootLoader里是否做了同样的配置。否则一旦BootLoader配置了其他功能，跳转到APP就会配置失效，需要留意