docker 运行redis挂载数据

拉取redis镜像

docker pull redis:latest

创建宿主机挂载信息

mkdir /home/redis/data
mkdir /home/redis/conf

在 /home/redis/conf下创建redis.conf （下面是精简化的redis.conf文件 copy过去即用）

bind *
protected-mode no
port 6380
timeout 0
tcp-keepalive 300
daemonize no
supervised no
pidfile /var/run/redis_6379.pid
loglevel notice
logfile ""
databases 16
always-show-logo yes
save 900 1
save 300 10
save 60 10000
stop-writes-on-bgsave-error yes
rdbcompression yes
rdbchecksum yes
dbfilename dump.rdb
dir ./
slave-serve-stale-data yes
slave-read-only yes
repl-diskless-sync no
repl-diskless-sync-delay 5
repl-disable-tcp-nodelay no
slave-priority 100
requirepass mywx
lazyfree-lazy-eviction no
lazyfree-lazy-expire no
lazyfree-lazy-server-del no
slave-lazy-flush no
appendonly no
appendfilename "appendonly.aof"
appendfsync everysec
no-appendfsync-on-rewrite no
auto-aof-rewrite-percentage 100
auto-aof-rewrite-min-size 64mb
aof-load-truncated yes
aof-use-rdb-preamble no
lua-time-limit 5000
slowlog-log-slower-than 10000
slowlog-max-len 128
latency-monitor-threshold 0
hash-max-ziplist-entries 512
hash-max-ziplist-value 64
list-max-ziplist-size -2
list-compress-depth 0
set-max-intset-entries 512
zset-max-ziplist-entries 128
zset-max-ziplist-value 64
hll-sparse-max-bytes 3000
activerehashing yes
client-output-buffer-limit normal 0 0 0
client-output-buffer-limit slave 256mb 64mb 60
client-output-buffer-limit pubsub 32mb 8mb 60
hz 10
aof-rewrite-incremental-fsync yes

运行容器

docker run -p 6380:6380 --name redis -v /home/redis/conf/redis.conf:/etc/redis/redis.conf -v /home/redis/data:/data -d redis:latest redis-server /etc/redis/redis.conf  --requirepass "mywx" --appendonly yes

解释

• -p 映射端口
• –name 指定容器名称
• -v 挂在卷
• -d 后台启动
• –requirepass 密码
• redis-server /etc/redis/edis.conf 指定配置文件启动redis-server进程
• –appendonly 开启数据持久化

可能遇到到问题

• 挂载数据路径不对导致
• 还是路径映射问题

查找类似问题发现是防火墙问题
先关闭selinux

setenforce 0

再修改 把SELINUX改成 SELINUX=disable

vi /etc/selinux/config
 
# This file controls the state of SELinux on the system.
# SELINUX= can take one of these three values:
#     enforcing - SELinux security policy is enforced.
#     permissive - SELinux prints warnings instead of enforcing.
#     disabled - No SELinux policy is loaded.
SELINUX=disable
# SELINUXTYPE= can take one of three values:
#     targeted - Targeted processes are protected,
#     minimum - Modification of targeted policy. Only selected processes are protected.
#     mls - Multi Level Security protection.
SELINUXTYPE=targeted

再次启动