- 博客(11)
- 资源 (2)
- 收藏
- 关注
RSS订阅原创 Draws Arduino with AD, including schematic diagram and challenge I met
I use Altium Designer15.Drawing is the Arduino uno board.Including four part circuits（Power supply circuit, Comparison circuit, USB Download circuit and AVR single chip microcomputer circuit）The comparison circuit is the most interesting part I think.
2021-10-12 18:45:30
135
原创 Remote control desk lamp based on ESP8266
Hardwaremicro USBUSB JACKSrelaySome of resistance and capacitanceESP8266-12FCH340CHardware circuitUSB to UART one button download circuit5V to 3.3V circuit (voltage reduction, power supply)Esp8266-12f main control circuitKey circuitRelay ci
2021-10-12 18:43:39
232
原创 Clock-in Statistics System for “Xuexi Qiangguo”
The project is purely softwareAt present, the drilling of learning ability is realized in the form of ** website **. Its original design purpose is to improve the accuracy of statistics and facilitate the students on duty to watch the clock in every day,
2021-10-12 18:42:35
357
原创 Building Elevator System Based on 51 Single-chip Microcomputer
Project forecastThis project is a pure hardware project.Project composition: AT89C52 controller. 0.36 inch Nixie Tube. 3.0mm 8*8LED dot matrix. JQ8400FL10P voice broadcast. Other component design drawings are marked.This project will only give PcbDoc fi
2021-10-12 18:41:24
201
原创 Real-time monitoring of ambient temperature base on Nodemcu / ESP12F
nodemcu/ESP12F Real-time monitoring of ambient temperature.Bigiot renderings are as follows：Realization ideaFirstly,connect the device to the internet.Connect the BIGIOT net.Send information regularly.I have searched a lot of data, but I have not
2021-10-10 00:28:01
1575
原创 Detailed explanation of application effect and code of soil humidity sensor base on nodemcu/ESP12F
First, attach the effect drawing. In order to facilitate debugging and writing code, I use ** Arduino ide ** to write code.Window monitor print real-time effect:The hardware circuit diagram is drawn by myself and made by the merchant. The following figu
2021-10-10 00:26:22
1883
原创 Remote control car base on MCS 51
1.Circuit DesignBefore you start, determine the components to use.Try to select the components that control the trolley.As the title：Main control chip：AT89C52 chipA toy car（which have two motor.The front motor controls the left and right, and the rear
2021-10-09 20:23:47
468
原创 nodemcu/ESP12F贝壳物联实时传数据到接口
nodemcu/ESP12F贝壳物联实时监控环境温度贝壳物联效果图如下：实现思路先联网连上贝壳物联定时发送信息我本人查找了很多资料，没有发现实际有效的资料能够辅助我完成。于是我自己看文档借助贝壳物联的控制代码进行改造成传信息的代码。可能是全网首创非lua的C语言代码。关键代码：//上传信息到接口关键代码 String msg1 ="{\"M\":\"update\",\"ID\":\""+did+"\",\"V\":{\""+inputid+"\":\""+value+"\"}}
2021-02-19 14:30:52
506
2
原创 nodemcu/ESP12F土壤湿度传感器使用效果及代码详解
nodemcu/ESP12F/ESP8266+土壤湿度传感器使用效果及代码详解我所使用的土壤湿度传感器引脚如图某宝详情土壤湿度传感器与nodemcu接线（ESP12F/ESP8266也可参考）代码中所读取的是模拟信号值，其实只用接*AO，GND，VCC*三个引脚代码部分代码下载首先附上效果图，为了方便调试书写代码，本人用arduino IDE来书写代码。窗口监视器打印实时效果硬件是我自己画板交给商家制作的，下图是我实际硬件图我所使用的土壤湿度传感器引脚如图某宝详情土壤湿度传感器与node
2021-02-04 13:48:40
2943
2
原创 基于51单片机的楼宇电梯系统
项目预告该项目为纯硬件项目项目构成：主控芯片为51单片机，0.36英寸 共阳数码管，3.0mm 8*8共阳点阵,JQ8400FL10P语音模块，其它元器件设计图有标这个项目就只给PcbDoc文件啦，避免大家不动手画图，或者复制粘贴改改就完事由于是很久之前做的课程设计，这个还有仿真设计 Proteus文件，Proteus版本是8.6敬请期待，有空更（2020.11.04）...
2020-11-05 09:39:18
467
原创 ESP8266远程控制台灯(硬件软件详解)
硬件micro USBUSB母座继电器电阻电容若干ESP8266-12FCH340C硬件电路USB转UART一键下载电路5V转3.3V电路（降压、供电）ESP8266-12F主控电路key电路继电器电路此处设计为了给USB供电充足，避免供电不足灯频闪，加了个电容，利用电容充放电来提供充足电压（这是我个人的想法，不知正确否，实际测试过才行，也欢迎各位读者批评指正）总电路原理图2020.8.28翻车部分 板子到了焊接，第一块板在所有焊接完成后，
2020-11-05 09:36:06
4385
空空如也
TA创建的收藏夹 TA关注的收藏夹
TA关注的人