如何在linux中安装并使用traceroute工具

如何在linux中安装并使用traceroute工具

安装方法:
yum install -y traceroute

使用方法:
traceroute +目标主机地址

eg:#traceroute baidu.com
在这里插入图片描述
在这里插入图片描述

一般当一行出现‘ * ’号时表示断开连接,一般情况下很难复连。
补充:在window中命令使用的方法为
#tracert +目标主机地址

#traceroute
作用:查看traceroute工具的具体用法

Usage:
  traceroute [ -46dFITnreAUDV ] [ -f first_ttl ] [ -g gate,... ] [ -i device ] [ -m max_ttl ] [ -N squeries ] [ -p port ] [ -t tos ] [ -l flow_label ] [ -w waittime ] [ -q nqueries ] [ -s src_addr ] [ -z sendwait ] [ --fwmark=num ] host [ packetlen ]
Options:
  -4                          Use IPv4
  -6                          Use IPv6
  -d  --debug                 Enable socket level debugging
  -F  --dont-fragment         Do not fragment packets
  -f first_ttl  --first=first_ttl
                              Start from the first_ttl hop (instead from 1)
  -g gate,...  --gateway=gate,...
                              Route packets through the specified gateway
                              (maximum 8 for IPv4 and 127 for IPv6)
  -I  --icmp                  Use ICMP ECHO for tracerouting
  -T  --tcp                   Use TCP SYN for tracerouting (default port is 80)
  -i device  --interface=device
                              Specify a network interface to operate with
  -m max_ttl  --max-hops=max_ttl
                              Set the max number of hops (max TTL to be
                              reached). Default is 30
  -N squeries  --sim-queries=squeries
                              Set the number of probes to be tried
                              simultaneously (default is 16)
  -n                          Do not resolve IP addresses to their domain names
  -p port  --port=port        Set the destination port to use. It is either
                              initial udp port value for "default" method
                              (incremented by each probe, default is 33434), or
                              initial seq for "icmp" (incremented as well,
                              default from 1), or some constant destination
                              port for other methods (with default of 80 for
                              "tcp", 53 for "udp", etc.)
  -t tos  --tos=tos           Set the TOS (IPv4 type of service) or TC (IPv6
                              traffic class) value for outgoing packets
  -l flow_label  --flowlabel=flow_label
                              Use specified flow_label for IPv6 packets
  -w waittime  --wait=waittime
                              Set the number of seconds to wait for response to
                              a probe (default is 5.0). Non-integer (float
                              point) values allowed too
  -q nqueries  --queries=nqueries
                              Set the number of probes per each hop. Default is
                              3
  -r                          Bypass the normal routing and send directly to a
                              host on an attached network
  -s src_addr  --source=src_addr
                              Use source src_addr for outgoing packets
  -z sendwait  --sendwait=sendwait
                              Minimal time interval between probes (default 0).
                              If the value is more than 10, then it specifies a
                              number in milliseconds, else it is a number of
                              seconds (float point values allowed too)
  -e  --extensions            Show ICMP extensions (if present), including MPLS
  -A  --as-path-lookups       Perform AS path lookups in routing registries and
                              print results directly after the corresponding
                              addresses
  -M name  --module=name      Use specified module (either builtin or external)
                              for traceroute operations. Most methods have
                              their shortcuts (`-I' means `-M icmp' etc.)
  -O OPTS,...  --options=OPTS,...
                              Use module-specific option OPTS for the
                              traceroute module. Several OPTS allowed,
                              separated by comma. If OPTS is "help", print info
                              about available options
  --sport=num                 Use source port num for outgoing packets. Implies
                              `-N 1'
  --fwmark=num                Set firewall mark for outgoing packets
  -U  --udp                   Use UDP to particular port for tracerouting
                              (instead of increasing the port per each probe),
                              default port is 53
  -UL                         Use UDPLITE for tracerouting (default dest port
                              is 53)
  -D  --dccp                  Use DCCP Request for tracerouting (default port
                              is 33434)
  -P prot  --protocol=prot    Use raw packet of protocol prot for tracerouting
  --mtu                       Discover MTU along the path being traced. Implies
                              `-F -N 1'
  --back                      Guess the number of hops in the backward path and
                              print if it differs
  -V  --version               Print version info and exit
  --help                      Read this help and exit

Arguments:
+     host          The host to traceroute to
      packetlen     The full packet length (default is the length of an IP
                    header plus 40). Can be ignored or increased to a minimal
                    allowed value

除了使用内部命令行之外,我给大家也推荐一个UI网站工具

在线工具网址:http://tool.chinaz.com

该网址可用来检测网速、ping网址、IP查询、死链查询等。。。

在这里插入图片描述

评论
添加红包

请填写红包祝福语或标题

红包个数最小为10个

红包金额最低5元

当前余额3.43前往充值 >
需支付:10.00
成就一亿技术人!
领取后你会自动成为博主和红包主的粉丝 规则
hope_wisdom
发出的红包
实付
使用余额支付
点击重新获取
扫码支付
钱包余额 0

抵扣说明:

1.余额是钱包充值的虚拟货币,按照1:1的比例进行支付金额的抵扣。
2.余额无法直接购买下载,可以购买VIP、付费专栏及课程。

余额充值