esp8266 一直闪蓝灯 一直重启

串口打印如下信息

ets Jan 8 2013,rst cause:2, boot mode:(3,7)

load 0x40100000, len 25960, room 16
tail 8
chksum 0xf4
load 0x3ffe8000, len 1272, room 0
tail 8
chksum 0xdd
load 0x3ffe8500, len 2640, room 0
tail 0
chksum 0x47
csum 0x47
rf_cal[0] !=0x05,is 0xE9

原因：未进行分区注册

在user_main.c中加入如下宏定义和函数即可

#if ((SPI_FLASH_SIZE_MAP == 0) || (SPI_FLASH_SIZE_MAP == 1))
#error "The flash map is not supported"
#elif (SPI_FLASH_SIZE_MAP == 2)
#define SYSTEM_PARTITION_OTA_SIZE							0x6A000
#define SYSTEM_PARTITION_OTA_2_ADDR							0x81000
#define SYSTEM_PARTITION_RF_CAL_ADDR						0xfb000
#define SYSTEM_PARTITION_PHY_DATA_ADDR						0xfc000
#define SYSTEM_PARTITION_SYSTEM_PARAMETER_ADDR				0xfd000
#define SYSTEM_PARTITION_CUSTOMER_PRIV_PARAM_ADDR           0x7c000
#elif (SPI_FLASH_SIZE_MAP == 3)
#define SYSTEM_PARTITION_OTA_SIZE							0x6A000
#define SYSTEM_PARTITION_OTA_2_ADDR							0x81000
#define SYSTEM_PARTITION_RF_CAL_ADDR						0x1fb000
#define SYSTEM_PARTITION_PHY_DATA_ADDR						0x1fc000
#define SYSTEM_PARTITION_SYSTEM_PARAMETER_ADDR				0x1fd000
#define SYSTEM_PARTITION_CUSTOMER_PRIV_PARAM_ADDR           0x7c000
#elif (SPI_FLASH_SIZE_MAP == 4)
#define SYSTEM_PARTITION_OTA_SIZE							0x6A000
#define SYSTEM_PARTITION_OTA_2_ADDR							0x81000
#define SYSTEM_PARTITION_RF_CAL_ADDR						0x3fb000
#define SYSTEM_PARTITION_PHY_DATA_ADDR						0x3fc000
#define SYSTEM_PARTITION_SYSTEM_PARAMETER_ADDR				0x3fd000
#define SYSTEM_PARTITION_CUSTOMER_PRIV_PARAM_ADDR           0x7c000
#elif (SPI_FLASH_SIZE_MAP == 5)
#define SYSTEM_PARTITION_OTA_SIZE							0x6A000
#define SYSTEM_PARTITION_OTA_2_ADDR							0x101000
#define SYSTEM_PARTITION_RF_CAL_ADDR						0x1fb000
#define SYSTEM_PARTITION_PHY_DATA_ADDR						0x1fc000
#define SYSTEM_PARTITION_SYSTEM_PARAMETER_ADDR				0x1fd000
#define SYSTEM_PARTITION_CUSTOMER_PRIV_PARAM_ADDR           0xfc000
#elif (SPI_FLASH_SIZE_MAP == 6)
#define SYSTEM_PARTITION_OTA_SIZE							0x6A000
#define SYSTEM_PARTITION_OTA_2_ADDR							0x101000
#define SYSTEM_PARTITION_RF_CAL_ADDR						0x3fb000
#define SYSTEM_PARTITION_PHY_DATA_ADDR						0x3fc000
#define SYSTEM_PARTITION_SYSTEM_PARAMETER_ADDR				0x3fd000
#define SYSTEM_PARTITION_CUSTOMER_PRIV_PARAM_ADDR           0xfc000
#else
#error "The flash map is not supported"
#endif

#define SYSTEM_PARTITION_CUSTOMER_PRIV_PARAM                SYSTEM_PARTITION_CUSTOMER_BEGIN


void ICACHE_FLASH_ATTR user_pre_init(void)
{
    if(!system_partition_table_regist(at_partition_table, sizeof(at_partition_table)/sizeof(at_partition_table[0]),SPI_FLASH_SIZE_MAP)) {
		os_printf("system_partition_table_regist fail\r\n");
		os_printf("SPI_FLASH_SIZE_MAP : %d \r\n",SPI_FLASH_SIZE_MAP);
		while(1);
	}
}

具体可以参考IOTDemo的写法