Mtk屏驱动修改

屏是三大件中最首要的器件 下文以Mtk6755 Android9作为正文内容

主要涉及文件：

修改：	
    modified:   device/mediateksample/k50v1_64_bsp/ProjectConfig.mk
    modified:   kernel-3.18/arch/arm64/configs/k50v1_64_bsp_debug_defconfig
	modified:   kernel-3.18/arch/arm64/configs/k50v1_64_bsp_defconfig
	modified:   kernel-3.18/drivers/misc/mediatek/lcm/mt65xx_lcm_list.c
	modified:   kernel-3.18/drivers/misc/mediatek/lcm/mt65xx_lcm_list.h
	modified:   vendor/mediatek/proprietary/bootable/bootloader/lk/dev/lcm/mt65xx_lcm_list.c
	modified:   vendor/mediatek/proprietary/bootable/bootloader/lk/project/k50v1_64_bsp.mk

新增：
    kernel-3.18/drivers/misc/mediatek/lcm/otm1282b_hd720_jd4p7/
    vendor/mediatek/proprietary/bootable/bootloader/lk/dev/lcm/otm1282b_hd720_jd4p7/

lcm代码修改

otm1282b_hd720_jd4p7/Makefile

驱动编译文件添加obj-y += otm1282b_hd720_jd4p7.o

obj-y += otm1282b_hd720_jd4p7.o

ccflags-$(CONFIG_MTK_LCM) += -I$(srctree)/drivers/misc/mediatek/lcm/inc

otm1282b_hd720_jd4p7/otm1282b_hd720_jd4p7.c

1、驱动结构体名称修改

LCM_DRIVER otm1282b_hd720_jd4p7_lcm_drv = 
{
    .name			= "otm1282b_hd720_jd4p7",//LCM 的型号名，lk的型号名和kernel 型号名必须保持一致，否则会重启
	.set_util_funcs = lcm_set_util_funcs, 
	.compare_id = lcm_compare_id, //LCM ID 获取，只有在lk有效，lk在启动阶段会调用该接口，通过返回值来判断当前lcm模组与驱动匹配，用于多模组时驱动兼容设计
	.get_params     = lcm_get_params, //lcm 显示和mipi 时序参数配置
	.init           = lcm_init, //lcm 的初始化参数
	.suspend        = lcm_suspend, //休眠
	.resume         = lcm_resume, //唤醒
};

2、根据HW连接修改LCM类型、DSI模式、LCM大小配置基本信息

#define FRAME_WIDTH  										(720)
#define FRAME_HEIGHT 										(1280)

3、屛的初始化参数（需要屛厂给出参数，参数不对会导致花屏现象）

static struct LCM_setting_table lcm_initialization_setting[] = {
// 屏幕配置初始化
        {0xff,5,{0x77,0x01,0x00,0x00,0x10}},                                                               
        {0xC0,2,{0x63,0x00}},                                                                             
        {0xC1,2,{0x11,0x02}},                                                                             
        {0xC2,2,{0x31,0x08}},   
.........
        {0xff,5,{0x77,0x01,0x00,0x00,0x00}},   
        {0X29,0,{}},
                    
//以下一般不用改                                       
{0x11,01,{0x00}},
{REGFLAG_DELAY, 120, {}},  
{0x29,01,{0x00}},       
{REGFLAG_DELAY, 20, {}},  
{REGFLAG_END_OF_TABLE, 0x00, {}}
};

4、配置垂直线，水平像素及相关数据格式设置（对于时序的话，一般要求不高可以不需要改，如要改需要让屛厂提供）

static void lcm_get_params(LCM_PARAMS *params)
{
params->width  = FRAME_WIDTH;
params->height = FRAME_HEIGHT;
// enable tearing-free
params->dbi.te_mode                         = LCM_DBI_TE_MODE_VSYNC_ONLY;
params->dbi.te_edge_polarity                = LCM_POLARITY_RISING;

#if (LCM_DSI_CMD_MODE)
                params->dsi.mode   = CMD_MODE;
#else
        params->dsi.mode   =SYNC_PULSE_VDO_MODE; //SYNC_PULSE_VDO_MODE; //BURST_VDO_MODE;
        //params->dsi.mode   = BURST_VDO_MODE;
#endif

// DSI
/* Command mode setting */        
params->dsi.LANE_NUM                        = LCM_TWO_LANE;//修改mipi通道数,根据实际模组打样来配置(询问FAE得知)
params->dsi.data_format.format      = LCM_DSI_FORMAT_RGB888;
//video mode timing
params->dsi.PS=LCM_PACKED_PS_24BIT_RGB888;

params->dsi.vertical_sync_active        = 4;//垂直同步信号的宽度
params->dsi.vertical_backporch        = 16;//垂直同步信号的后沿
params->dsi.vertical_frontporch        = 20;//垂直同步信号的前沿,可调节竖屏 上线白线条，闪屏
params->dsi.vertical_active_line                                = FRAME_HEIGHT;

params->dsi.horizontal_sync_active                        = 10;
params->dsi.horizontal_backporch                        = 78;
params->dsi.horizontal_frontporch                        = 80;
params->dsi.horizontal_active_pixel                        = FRAME_WIDTH;

params->dsi.PLL_CLOCK = 180;//lcm的频率，更据实际情况改动，这个一般mtk的都会影响gps的信号强弱。        

}

@关于PLL_CLOCK的计算
1、DSI vdo mode下的数据速率data_rate的大致计算公式为：
(Data rate) = (height + vsa + vbp + vfp) * (width + hsa + hbp + hfp) * total_bit_per_pixel * frame_per_second / total_lane_num

2、DSI cmd mode下的数据速率data_rate的大致计算公式为：
(Data rate) = widthheight1.2* total_bit_per_pixel*frame_per_second/total_lane_num

参数注释：
data_rate ： 表示的是数据速率
width，height ：屏幕分辨率
VSA VBP VFP ：DSI vdo mode的vertical porch配置参数
HSA HBP HFP ：DSI vdo mode的horizontal porch配置参数
total_bit_per_pixel ：表示的是一个pixel需要用几个bit来表示，比如RGB565的话就是16个bit/RGB888就是24bit
frame_per_second ：就是我们通常看到的fps，叫做帧率，表示每秒发送多少个帧，一般是60帧每秒
total_lane_num ：表示的是data lane

DSI采用的是双边采样，则clk等于数据速率的一半，也就是说一个clk周期内传送2位，所以你计算出来的值还要除以2，即PLL_CLOCK(clk )= Data rate/2;

5、实现LCM休眠/恢复功能

static void lcm_suspend(void)
{
    push_table(lcm_deep_sleep_mode_in_setting, sizeof(lcm_deep_sleep_mode_in_setting) / sizeof(struct LCM_setting_table), 1);
        SET_RESET_PIN(0);
        MDELAY(10);
        SET_RESET_PIN(1);
        MDELAY(10);
        SET_RESET_PIN(0);
        MDELAY(120);
｝
static void lcm_resume(void)
{
        SET_RESET_PIN(1);
        MDELAY(10);
        SET_RESET_PIN(0);
        MDELAY(10);
        SET_RESET_PIN(1);
        MDELAY(120);
    push_table(lcm_initialization_setting, sizeof(lcm_initialization_setting) / sizeof(struct LCM_setting_table), 1);
}

kerne层修改

将对应的屏幕驱动放在

kernel-3.18/drivers/misc/mediatek/lcm/下

添加：
kernel-3.18/drivers/misc/mediatek/lcm/otm1282b_hd720_jd4p7/Makefile
kernel-3.18/drivers/misc/mediatek/lcm/otm1282b_hd720_jd4p7/otm1282b_hd720_jd4p7.c

kernel-3.18/arch/arm64/configs/k50v1_64_bsp_debug_defconfig

kernel-3.18/arch/arm64/configs/k50v1_64_bsp_defconfig

修改配置文件中的LCM名称和分辨率：

CONFIG_CUSTOM_KERNEL_LCM="otm1282b_hd720_jd4p7"
CONFIG_LCM_HEIGHT="1280"
CONFIG_LCM_WIDTH="720"

kernel-3.18/drivers/misc/mediatek/lcm/mt65xx_lcm_list.c的LCM_DRIVER *lcm_driver_list[]

添加LCM的驱动型号到lcm_list中  注意大小写：

#if defined(OTM1282B_HD720_JD4P7)
       &otm1282b_hd720_jd4p7_lcm_drv,

在lcm_list.h中添加LCM名称：

kernel-3.18/drivers/misc/mediatek/lcm/mt65xx_lcm_list.h

+extern LCM_DRIVER otm1282b_hd720_jd4p7_lcm_drv;

lk层修改

将对应的屏幕驱动放在

vendor/mediatek/proprietary/bootable/bootloader/lk/dev/lcm/下

添加：
kernel-3.18/drivers/misc/mediatek/lcm/otm1282b_hd720_jd4p7/Makefile
kernel-3.18/drivers/misc/mediatek/lcm/otm1282b_hd720_jd4p7/otm1282b_hd720_jd4p7.c

添加LCM的驱动型号到lcm_list中  注意大小写

vendor/mediatek/proprietary/bootable/bootloader/lk/dev/lcm/mt65xx_lcm_list.c

1：
extern LCM_DRIVER otm1282b_hd720_jd4p7_lcm_drv;

2：
在LCM_DRIVER *lcm_driver_list[]中添加
#if defined(OTM1282B_HD720_JD4P7)
       &otm1282b_hd720_jd4p7_lcm_drv,

将新lcm的文件型号和对应的logo资源添加到lk的配置文件中

vendor/mediatek/proprietary/bootable/bootloader/lk/project/k50v1_64_bsp.mk

CUSTOM_LK_LCM="otm1282b_hd720_jd4p7"
BOOT_LOGO :=hd720

device下修改

修改项目对应的ProjectConfig.mk

device/mediateksample/k50v1_64_bsp/ProjectConfig.mk

LCM_HEIGHT = 1280
LCM_WIDTH = 720
BOOT_LOGO = hd720