ESP8266-2-WIFI连接+LED控制

WIFI网络通信通常有两种设备
1无线接入点（AP），相当于提供热点的设备，AP和AP可以相互连接。
2无线终端（STA），连接到AP的装置，这个模式不允许其他设备接入。

查看官方列程
http://docs.micropython.org/en/latest/esp8266/quickref.html

1、以下是连接我的手机热点代码

import network
wlan = network.WLAN(network.STA_IF) # create station interface
wlan.active(True)       # 激活wifi
wlan.scan()             # 扫描wifi
wlan.isconnected()      #检测设备是否连接上
wlan.connect('iPhone and yu', '1234567890') # 名字+密码
wlan.config('mac')      # get the interface's MAC address 校验
wlan.ifconfig()  # get the interface's IP/netmask/gw/DNS获取本机IP信息

连接以后默认开机进行连接（默认永久连接状态，之前LED灯复位后，代码会自动删除，这个不会）
通过终端输入这个 wlan.ifconfig() 可以打印本机信息

2、通信测试（开发板与PC端数据通信）

from socket import *
import network
wlan = network.WLAN(network.STA_IF) # create station interface
wlan.active(True)       # activate the interface
wlan.scan()             # scan for access points
wlan.isconnected()      # check if the station is connected to an AP
wlan.connect('zufangzhaoziru301', 'zufangzhaoziru') # connect to an AP
wlan.config('mac')      # get the interface's MAC address
wlan.ifconfig()         # get the interface's IP/netmask/gw/DNS addresses

udp_socket = socket(AF_INET, SOCK_DGRAM)#创建UDP
dest_addr = ('192.168.18.185', 8080)#输入电脑地址和端口
send_data = "hello world"#需要发送的消息
udp_socket.sendto(send_data.encode('utf-8'), dest_addr)//数据发送

可以才看到上位机接受到了数据

3、我们让上位机发送数据给esp8266接受试试，那么接收就要使用接收的命令

from socket import *
import network

wlan = network.WLAN(network.STA_IF) # create station interface
wlan.active(True)       # activate the interface
wlan.scan()             # scan for access points
wlan.isconnected()      # check if the station is connected to an AP
wlan.connect('zufangzhaoziru301', 'zufangzhaoziru') # connect to an AP
wlan.config('mac')      # get the interface's MAC address
wlan.ifconfig()         # get the interface's IP/netmask/gw/DNS addresses

udp_socket = socket(AF_INET, SOCK_DGRAM)
dest_addr = ('192.168.18.185', 8080)
send_data = "hello world"
udp_socket.sendto(send_data.encode('utf-8'), dest_addr)

recv_data = udp_socket.recvfrom(1024)
print('%c',recv_data)

可以看见已经接受到了上位机发来的数据了

4、接下来就用PC端控制开发板LED啦

from socket import *
import network
import machine
import time

wlan = network.WLAN(network.STA_IF) # create station interface
wlan.active(True)       # activate the interface
wlan.scan()             # scan for access points
wlan.isconnected()      # check if the station is connected to an AP
wlan.connect('zufangzhaoziru301', 'zufangzhaoziru') # connect to an AP
wlan.config('mac')      # get the interface's MAC address
wlan.ifconfig()         # get the interface's IP/netmask/gw/DNS addresses

while not wlan.isconnected():#连接成功
   print('正在连接网络....')
   time.sleep(1)
   
print('network config -OK:',wlan.ifconfig())


udp_socket = socket(AF_INET, SOCK_DGRAM)#UDP套接字创建
udp_socket.bind(("0.0.0.0",7788))#绑定固定ip 端口
dest_addr = ('192.168.18.185', 8080)


pin16 = machine.Pin(16,machine.Pin.OUT)

while True: 
    #拆包
    recv_data, sender_info  = udp_socket.recvfrom(1024)#等待数据接收1024 字节
    print("{}发送的数据,{}".format(sender_info,recv_data))#b代表没有解码
    
    recv_data_str = recv_data.decode("utf-8")#解码
    print("解码后的数据，{},".format(recv_data_str))
    
    
    if recv_data_str == "亮":
        pin16.value(0)
    elif recv_data_str == "灭":
        pin16.value(1)
    time.sleep(1)