vlan综合实验

 三、配置思路
1、在各个交换机上创建vlan
2、将接口加入相应vlan，并配置端口的链路模式
3、在trunk干道上放行vlan
4、配置路由器子接口
5、配置DHCP地址池，并测试

三个交换机创建vlan

port link-type access //更改接口模式

port defualt   //配置接口默认vlan

[SW1-Ethernet0/0/1]port link-type trunk

[SW1-Ethernet0/0/1]port trunk allow-pass vlan 2 3

[SW2-Ethernet0/0/2]port link-type trunk

[SW2-Ethernet0/0/2]port trunk allow-pass vlan 2 3

[SW2-Ethernet0/0/1]port link-type trunk

[SW2-Ethernet0/0/1]port trunk allow-pass vlan 2 3

[SW3-Ethernet0/0/1]port link-type trunk
[SW3-Ethernet0/0/1]port trunk allow-pass vlan 2 3

交换机配置完毕

路由器部分 给每一个vlan配网关

（路由器左边部分）

[R1]int g0/0/0.2
[R1-GigabitEthernet0/0/0.2]ip add 192.168.1.254 24  
[R1-GigabitEthernet0/0/0.2]dot1q termination vid 2  //封装  接口划分给 2

[R1-GigabitEthernet0/0/0.2]arp broadcast enable   //开启arp广播

[R1]int g0/0/0.3
[R1-GigabitEthernet0/0/0.3]ip add 192.168.2.254 24
[R1-GigabitEthernet0/0/0.3]dot1q termination vid 3

[R1-GigabitEthernet0/0/0.3]arp broadcast enable 

（路由器右边部分）

[R1]int g0/0/1.2
[R1-GigabitEthernet0/0/1.2]ip add 192.168.3.254 24

[R1-GigabitEthernet0/0/1.2]dot1q termination vid 2

[R1-GigabitEthernet0/0/1.2]arp broadcast enable 

[R1]int g0/0/1.3
[R1-GigabitEthernet0/0/1.3]ip add 192.168.4.254 24

[R1-GigabitEthernet0/0/1.3]dot1q termination vid 3

[R1-GigabitEthernet0/0/1.3]arp broadcast enable 

DHCP配置地址池服务

[R1]dhcp enable  
[R1]ip pool aa  //配置左边的vlan2
[R1-ip-pool-aa]network 192.168.1.0 mask 24  //宣告网段
[R1-ip-pool-aa]gateway-list 192.168.1.254  //配置网关

[R1-ip-pool-aa]dns-list 8.8.8.8

下发dhcp服务

[R1]int g0/0/0.2

[R1-GigabitEthernet0/0/0.2]dhcp select global 

检查

 配置左边vlan3的

[R1-ip-pool-bb]gateway-list 192.168.2.254
[R1-ip-pool-bb]dns-list 8.8.8.8

[R1-GigabitEthernet0/0/0.3]dhcp select global 

右边vlan2的

[R1-ip-pool-cc]network 192.168.3.0 mask 24

[R1-ip-pool-cc]gateway-list 192.168.3.254

[R1-ip-pool-cc]dns-list 8.8.8.8

[R1-GigabitEthernet0/0/1.2]dhcp select global 

vlan3的

[R1-ip-pool-dd]network 192.168.4.0 mask 24

[R1-ip-pool-dd]gateway-list 192.168.4.254

[R1-ip-pool-dd]dns-list 8.8.8.8

[R1-GigabitEthernet0/0/1.3]dhcp select global 

所有配置结束

1、查看是否可以使用dhcp获取地址

 

 

 

 ok