启动分析

U-Boot 1.1.4 (Oct 23 2012 - 19:10:08)           // uboot版本信息

U-boot AP123

DRAM:  32 MB                                                         // 内存大小                  
Flash Manuf Id 0x1c, DeviceId0 0x30, DeviceId1 0x16
flash size 4MB, sector count = 64                         // flash大小
Flash:  4 MB
Using default environment

Initializing NVRAM...Done.
In:    serial
Out:   serial
Err:   serial
ag934x_enet_initialize...
Fetching MAC Address from 0x81fe3968
Fetching MAC Address from 0x81fe3968
 wasp  reset mask:c03300
WASP ----> S27 PHY
: cfg1 0x80000000 cfg2 0x7114
eth0: 00:03:7f:11:23:2e
s27 reg init
WASP ----> S27 PHY
: cfg1 0xf cfg2 0x7214
eth1: 00:03:7f:11:23:2f
s27 reg init lan
ATHRS27: resetting s27
ATHRS27: s27 reset done
eth0, eth1
Press Ctrl-C to enter Bootloader:  0     //提示（ bootloader 启动倒计时）

相同（1）：好的格式
## Booting image at 9f010000 ...         // 内核启动地址
   Image Name:   Linux Kernel Image
   Created:      2013-01-18  10:11:58 UTC
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    1026420 Bytes = 1002.4 kB
   Load Address: 80002000
   Entry Point:  8022e350
   Verifying Checksum at 0x9f010040 ...OK
   Uncompressing Kernel Image ... OK

Starting kernel ...

Linux version 2.6.31--LSDK-9.2.0_U10.5.13 (root@lqdesk) (gcc version 4.3.3 (GCC) ) #465 Tue Jan 15 18:04:12 CST 2013

相同（2）： cpu时钟

flash_size passed from bootloader = 4
arg 1: console=ttyS0,115200
arg 2: root=31:02
arg 3: init=/sbin/init
arg 4: mtdparts=ath-nor0:64k(u-boot),1024k(uImage),2816k(rootfs),64k(nvram),64k(mib0),64k(ART)
arg 5: mem=32M
CPU revision is: 0001974c (MIPS 74Kc)                                  // cpu体系结构
ath_sys_frequency: cpu srif ddr srif cpu 400 ddr 400 ahb 200

相同（3）：内存大小 和 内存分配
Determined physical RAM map:
 memory: 02000000 @ 00000000 (usable)
User-defined physical RAM map:
 memory: 02000000 @ 00000000 (usable)
Zone PFN ranges:
  Normal   0x00000000 -> 0x00002000
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
    0: 0x00000000 -> 0x00002000
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 8128
Kernel command line: console=ttyS0,115200 root=31:02 init=/sbin/init mtdparts=ath-nor0:64k(u-boot),1024k(uImage),2816k(rootfs),64k(nvram),64k(mib0),64k(ART) mem=32M                                                                                                                                                                          // 内存大小
PID hash table entries: 128 (order: 7, 512 bytes)
Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
Writing ErrCtl register=00000000
Readback ErrCtl register=00000000
Memory: 29424k/32768k available (2256k kernel code, 3344k reserved, 488k data, 136k init, 0k highmem)      // 内存分配
NR_IRQS:128
plat_time_init: plat time init done
Calibrating delay loop... 199.68 BogoMIPS (lpj=399360)
Mount-cache hash table entries: 512
NET: Registered protocol family 16

相同（4）：slab指代的是什么？？？

bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb

相同（5）：tcp
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 1024 (order: 1, 8192 bytes)
TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
TCP: Hash tables configured (established 1024 bind 1024)
TCP reno registered
NET: Registered protocol family 1
ATH GPIOC major 0
squashfs: version 4.0 (2009/01/31) Phillip Lougher
msgmni has been set to 57
alg: No test for lzma (lzma-generic)
alg: No test for stdrng (krng)
io scheduler noop registered
io scheduler deadline registered (default)
Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0xb8020000 (irq = 19) is a 16550A
console [ttyS0] enabled
brd: module loaded
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
PPP MPPE Compression module registered
NET: Registered protocol family 24
PPPoL2TP kernel driver, V1.0
Registered WAN Demand
cdc_ncm: 14-Mar-2012
usbcore: registered new interface driver cdc_ncm
ath-nor0: squash filesystem with lzma found at 0x00110000

相同（6）：Flash分块
Creating 5 MTD partitions on "ath-nor0":
0x000000000000-0x000000010000 : "u-boot"
0x000000010000-0x0000003e0000 : "uImage"
0x000000110000-0x0000003e0000 : "rootfs"
0x0000003e0000-0x0000003f0000 : "nvram"
0x0000003f0000-0x000000400000 : "art"
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
Port Status 1c000004
ath-ehci ath-ehci.0: ATH EHCI
ath-ehci ath-ehci.0: new USB bus registered, assigned bus number 1
ehci_reset Intialize USB CONTROLLER in host mode: 13
ehci_reset Port Status 1c000000
ath-ehci ath-ehci.0: irq 3, io mem 0x1b000000
ehci_reset Intialize USB CONTROLLER in host mode: 13
ehci_reset Port Status 1c000000
ath-ehci ath-ehci.0: USB 2.0 started, EHCI 1.00
usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: ATH EHCI
usb usb1: Manufacturer: Linux 2.6.31--LSDK-9.2.0_U10.5.13 ehci_hcd
usb usb1: SerialNumber: platform
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver usbserial
usbserial: USB Serial Driver core
USB Serial support registered for GSM modem (1-port)        // usb 为GSM模块
usbcore: registered new interface driver option
option: v0.7.2:USB Driver for GSM modems
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (512 buckets, 2048 max)
ctnetlink v0.93: registering with nfnetlink.
xt_time: kernel timezone is -0000
ip_tables: (C) 2000-2006 Netfilter Core Team
TCP cubic registered
NET: Registered protocol family 17
Registered Atheros GPIO device
Initialize GPIO...
Hardware watchdog registered with AHB_CLK=200000000
ath_otp_init: Registering OTP success
ath_clksw_init: Registering Clock Switch Interface success
Advanced NVRAM kernel device driver version 3.0.0 by Li Qi/Richard Lee <liqilinux@gmail.com>
AdvNVRAM: 253:0 (mtd: "nvram", offset: 0x00000000, size: 0x00010000, erasesize: 0x00010000, bufsize: 0x0000ff00)
Advanced NVRAM device registered successfully
VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
Freeing unused kernel memory: 136k freed
usb 1-1: new high speed USB device using ath-ehci and address 2

Starting architecture code for ar9341      // AR9341芯片
Huawei E8258 WiFi Router
Linux version 2.6.31--LSDK-9.2.0_U10.5.13 (root@lqdesk) (gcc version 4.3.3 (GCC) ) #465 Tue Jan 15 18:04:12 CST 2013
Release: E8258_21.010.01.00.12-2-g0bf62e1 2013-01-17 15:55:39 0bf62e14f6cc131b0ee287a0b09024ff3d5630d8
Build:   2013-01-18 18:11:19
InitProc: Setup base rootfs for kernel 2.6.31--LSDK-9.2.0_U10.5.13
InitProc: Setup dynamic rootfs with mdev
InitProc: Initialize init environments and console
InitProc: Setup IPC for generic signal/socket packet
InitProc: Initialize IPC signal for fatal/generic/specific signals
InitProc: Initialize IPC socket for pppd/dhcpc/http
InitProc: Setup UEvent NETLINK daemon
InitProc: Setup ModData main process
UEvent: Start uevent netlink daemon as pid=307
UEvent: Start devscan for kernel buildin modules
UEvent: USBDevice Process for 12d1:1506, recognized as E8238 Cellular Standard Mode with 5 ttys, 1 sddisk
Jan  1 00:00:02 UEvent: USBDevice Process for 12d1:1506, recognized as E8238 Cellular Standard Mode with 5 ttys, 1 sddisk
UEvent: USBDev TTY add for 12d1:1506:0102 TYPE=00:00:00 INTERFACE=ff:02:01 DEVTYPE=usb_interface SUBSYSTEM=tty devname=[ttyUSB0]
ModuleData: Start module data daemon as pid 308
ModuleData: Registered 16 module data
Jan  1 00:00:02 UEvent: USBDev TTY add for 12d1:1506:0102 TYPE=00:00:00 INTERFACE=ff:02:01 DEVTYPE=usb_interface SUBSYSTEM=tty devname=[ttyUSB0]
UEvent: USBDev TTY add for 12d1:1506:0102 TYPE=00:00:00 INTERFACE=ff:02:03 DEVTYPE=usb_interface SUBSYSTEM=tty devname=[ttyUSB1]
Jan  1 00:00:02 UEvent: USBDev TTY add for 12d1:1506:0102 TYPE=00:00:00 INTERFACE=ff:02:03 DEVTYPE=usb_interface SUBSYSTEM=tty devname=[ttyUSB1]
UEvent: USBDev TTY add for 12d1:1506:0102 TYPE=00:00:00 INTERFACE=ff:02:02 DEVTYPE=usb_interface SUBSYSTEM=tty devname=[ttyUSB2]
Jan  1 00:00:02 UEvent: USBDev TTY add for 12d1:1506:0102 TYPE=00:00:00 INTERFACE=ff:02:02 DEVTYPE=usb_interface SUBSYSTEM=tty devname=[ttyUSB2]
UEvent: Cellular 12d1:1506 TTY devices is now RECOGNIZED and READY as Data=/dev/ttyUSB0 ATCmd=/dev/ttyUSB2 Diag=/dev/ttyUSB1
Jan  1 00:00:02 UEvent: Cellular 12d1:1506 TTY devices is now RECOGNIZED and READY as Data=/dev/ttyUSB0 ATCmd=/dev/ttyUSB2 Diag=/dev/ttyUSB1
UEvent: Save IPC for cellular daemon as updated devstatus 0x00000006 ATCmd=/dev/ttyUSB2 Data=/dev/ttyUSB0 Diag=/dev/ttyUSB1
UEvent: USBDev TTY add for 12d1:1506:0102 TYPE=00:00:00 INTERFACE=ff:02:05 DEVTYPE=usb_interface SUBSYSTEM=tty devname=[ttyUSB3]
Jan  1 00:00:02 UEvent: USBDev TTY add for 12d1:1506:0102 TYPE=00:00:00 INTERFACE=ff:02:05 DEVTYPE=usb_interface SUBSYSTEM=tty devname=[ttyUSB3]
UEvent: USBDev TTY add for 12d1:1506:0102 TYPE=00:00:00 INTERFACE=ff:02:0a DEVTYPE=usb_interface SUBSYSTEM=tty devname=[ttyUSB4]
Jan  1 00:00:02 UEvent: USBDev TTY add for 12d1:1506:0102 TYPE=00:00:00 INTERFACE=ff:02:0a DEVTYPE=usb_interface SUBSYSTEM=tty devname=[ttyUSB4]
UEvent: Start uevent netlink listening at socket=6 nl_pid=0
InitProc: Setup TimerProc main process
TimerProc: Start timerproc management as pid 309
TimerProc: Start Timer Process listening as ticker=1
InitProc: Start NVRAM for user settings
start_nvram: Initialize NVRAM 1.0.0 system
start_nvram: NVRAM self-verify and consistency check
InitProc: Start SystemInit for system base initializing
sysinit-ar9341: Initialize Huawei E8238 Mobile Broadband Cellular Device
Jan  1 00:00:02 UEvent: UEvent as action=remove, devpath=/devices/platform/ath-ehci.0/usb1/1-1/1-1:1.0/ttyUSB0/tty/ttyUSB0 id=0000:0000:0000 bDevice=00:00:00 bInterface=00:00:00
UEvent: USBDev TTY remove for 12d1:1506:ffff TYPE=00:00:00 INTERFACE=00:00:00 DEVTYPE=usb_interface SUBSYSTEM=tty devname=[ttyUSB0]
Jan  1 00:00:02 UEvent: USBDev TTY remove for 12d1:1506:ffff TYPE=00:00:00 INTERFACE=00:00:00 DEVTYPE=usb_interface SUBSYSTEM=tty devname=[ttyUSB0]
UEvent: Cellular TTY devices is now REMOVED and DISABLED ttyUSB0
Jan  1 00:00:02 UEvent: Cellular TTY devices is now REMOVED and DISABLED
UEvent: Save IPC for cellular daemon as updated devstatus 0x00000000 ATCmd=/dev/ttyUSB2 Data=/dev/ttyUSB0 Diag=/dev/ttyUSB1
Jan  1 00:00:02 UEvent: UEvent as action=remove, devpath=/devices/platform/ath-ehci.0/usb1/1-1/1-1:1.0/ttyUSB0 id=0000:0000:0000 bDevice=00:00:00 bInterface=00:00:00
Jan  1 00:00:02 UEvent: UEvent as action=remove, devpath=/devices/platform/ath-ehci.0/usb1/1-1/1-1:1.0 id=12d1:1506:0258 bDevice=00:00:00 bInterface=ff:02:01
Jan  1 00:00:02 UEvent: UEvent as action=remove, devpath=/devices/platform/ath-ehci.0/usb1/1-1/1-1:1.1/ttyUSB1/tty/ttyUSB1 id=0000:0000:0000 bDevice=00:00:00 bInterface=00:00:00
UEvent: USBDev TTY remove for 12d1:1506:ffff TYPE=00:00:00 INTERFACE=00:00:00 DEVTYPE=usb_interface SUBSYSTEM=tty devname=[ttyUSB1]
Jan  1 00:00:02 UEvent: USBDev TTY remove for 12d1:1506:ffff TYPE=00:00:00 INTERFACE=00:00:00 DEVTYPE=usb_interface SUBSYSTEM=tty devname=[ttyUSB1]
Jan  1 00:00:02 UEvent: UEvent as action=remove, devpath=/devices/platform/ath-ehci.0/usb1/1-1/1-1:1.1/ttyUSB1 id=0000:0000:0000 bDevice=00:00:00 bInterface=00:00:00
Jan  1 00:00:02 UEvent: UEvent as action=remove, devpath=/devices/platform/ath-ehci.0/usb1/1-1/1-1:1.1 id=12d1:1506:0258 bDevice=00:00:00 bInterface=ff:02:03
Jan  1 00:00:02 UEvent: UEvent as action=remove, devpath=/devices/platform/ath-ehci.0/usb1/1-1/1-1:1.2/ttyUSB2/tty/ttyUSB2 id=0000:0000:0000 bDevice=00:00:00 bInterface=00:00:00
UEvent: USBDev TTY remove for 12d1:1506:ffff TYPE=00:00:00 INTERFACE=00:00:00 DEVTYPE=usb_interface SUBSYSTEM=tty devname=[ttyUSB2]
Jan  1 00:00:02 UEvent: USBDev TTY remove for 12d1:1506:ffff TYPE=00:00:00 INTERFACE=00:00:00 DEVTYPE=usb_interface SUBSYSTEM=tty devname=[ttyUSB2]
Jan  1 00:00:02 UEvent: UEvent as action=remove, devpath=/devices/platform/ath-ehci.0/usb1/1-1/1-1:1.2/ttyUSB2 id=0000:0000:0000 bDevice=00:00:00 bInterface=00:00:00
Jan  1 00:00:02 UEvent: UEvent as action=remove, devpath=/devices/platform/ath-ehci.0/usb1/1-1/1-1:1.2 id=12d1:1506:0258 bDevice=00:00:00 bInterface=ff:02:02
Jan  1 00:00:02 UEvent: UEvent as action=remove, devpath=/devices/platform/ath-ehci.0/usb1/1-1/1-1:1.3/host0/scsi_host/host0 id=0000:0000:0000 bDevice=00:00:00 bInterface=00:00:00
Jan  1 00:00:02 UEvent: UEvent as action=remove, devpath=/devices/platform/ath-ehci.0/usb1/1-1/1-1:1.3/host0 id=0000:0000:0000 bDevice=00:00:00 bInterface=00:00:00
Jan  1 00:00:02 UEvent: UEvent as action=remove, devpath=/devices/platform/ath-ehci.0/usb1/1-1/1-1:1.3 id=12d1:1506:0258 bDevice=00:00:00 bInterface=08:06:50
Jan  1 00:00:02 UEvent: UEvent as action=remove, devpath=/devices/platform/ath-ehci.0/usb1/1-1/1-1:1.4/ttyUSB3/tty/ttyUSB3 id=0000:0000:0000 bDevice=00:00:00 bInterface=00:00:00
UEvent: USBDev TTY remove for 12d1:1506:ffff TYPE=00:00:00 INTERFACE=00:00:00 DEVTYPE=usb_interface SUBSYSTEM=tty devname=[ttyUSB3]
Jan  1 00:00:02 UEvent: USBDev TTY remove for 12d1:1506:ffff TYPE=00:00:00 INTERFACE=00:00:00 DEVTYPE=usb_interface SUBSYSTEM=tty devname=[ttyUSB3]
Jan  1 00:00:02 UEvent: UEvent as action=remove, devpath=/devices/platform/ath-ehci.0/usb1/1-1/1-1:1.4/ttyUSB3 id=0000:0000:0000 bDevice=00:00:00 bInterface=00:00:00
Jan  1 00:00:02 UEvent: UEvent as action=remove, devpath=/devices/platform/ath-ehci.0/usb1/1-1/1-1:1.4 id=12d1:1506:0258 bDevice=00:00:00 bInterface=ff:02:05
Jan  1 00:00:02 UEvent: UEvent as action=remove, devpath=/devices/platform/ath-ehci.0/usb1/1-1/1-1:1.5/ttyUSB4/tty/ttyUSB4 id=0000:0000:0000 bDevice=00:00:00 bInterface=00:00:00
UEvent: USBDev TTY remove for 12d1:1506:ffff TYPE=00:00:00 INTERFACE=00:00:00 DEVTYPE=usb_interface SUBSYSTEM=tty devname=[ttyUSB4]
Jan  1 00:00:02 UEvent: USBDev TTY remove for 12d1:1506:ffff TYPE=00:00:00 INTERFACE=00:00:00 DEVTYPE=usb_interface SUBSYSTEM=tty devname=[ttyUSB4]
Jan  1 00:00:03 UEvent: UEvent as action=remove, devpath=/devices/platform/ath-ehci.0/usb1/1-1/1-1:1.5/ttyUSB4 id=0000:0000:0000 bDevice=00:00:00 bInterface=00:00:00
Jan  1 00:00:03 UEvent: UEvent as action=remove, devpath=/devices/platform/ath-ehci.0/usb1/1-1/1-1:1.5 id=12d1:1506:0258 bDevice=00:00:00 bInterface=ff:02:0a
Jan  1 00:00:03 UEvent: UEvent as action=remove, devpath=/devices/platform/ath-ehci.0/usb1/1-1/usb_device/usbdev1.2 id=0000:0000:0000 bDevice=00:00:00 bInterface=00:00:00
Jan  1 00:00:03 UEvent: UEvent as action=remove, devpath=/devices/platform/ath-ehci.0/usb1/1-1 id=12d1:1506:0258 bDevice=00:00:00 bInterface=00:00:00
UEvent: USB Device 12d1:1506 was removed
BoardSettings: ether_hwaddr=00:03:7F:11:23:2E wlan_hwaddr=78:F5:FD:1E:91:77
BoardSettings: serialno=E823812929000317 uuid=77EA6AA5-117A-45B3-9041-390CB957BDFF
BoardSettings: SSID=XLIGHT-9177 KEY=36D15A27
BoardSettings: flaglist=FF:FF:FF:FF:FF:FF:FF:FF:FF:FF:FF:FF:FF:FF:FF:FF:FF:FF:FF:FF:FF:FF:FF:FF:FF:FF:FF:FF:FF:FF:FF:FF
SysInit: Setup generic settings for SOHU router
SysInit: Set TCP/IP stacks settings for kernel 2.6.x
SysInit: Set system default hostname to E8258
SysInit: Set default login user settings
sysinit-ar9341: Initialize platform ethernet driver
sysinit-ar9341: Initialize platform wireless driver
sysinit-ar9341: Create wireless interfaces as AP
sysinit-ar9341: Can't find LAN hardware interface eth0
sysinit-ar9341: Can't find WAN hardware interface eth1
sysinit-ar9341: Initialize LAN[0] as ethername=[] apid=0x00000001 wdsid=0x00000003 staid=0x00000000
sysinit-ar9341: Initialize 4 Multi-WANs
sysinit-ar9341: Create WAN[0] as ethername=[] etheraddr=00:03:7F:11:23:2F
sysinit-ar9341: Create WAN[1] as ethername=[] etheraddr=00:03:7F:11:23:2F
sysinit-ar9341: Create WAN[2] as ethername=[] etheraddr=00:03:7F:11:23:2F
sysinit-ar9341: Create WAN[3] as ethername=[] etheraddr=00:03:7F:11:23:2F
sysinit-ar9341: Initialize WLAN with 1 Multi-SSID and baseaddr is 78:F5:FD:1E:91:77
sysinit-ar9341: Create WLAN MSSID AP[0] hwaddr 78:F5:FD:1E:91:77 interface ath0
sysinit-ar9341: Initialize System Module Specific Data
InitProc: Setup Cellular Management main process
InitProc: Switch to INITIALIZE state in mainloop
SysWorkModeInit: Initialize System WorkMode
SysWorkMode: Refresh device settings for going to work in router mode
SysWorkMode: LAN[0] as lan_ifname=br0 lan_ifnames=ath0 lan_ifname_post=ath0
SysWorkMode: WAN[0] was disabled
SysWorkMode: WAN[1] was disabled
SysWorkMode: WAN[2] was disabled
SysWorkMode: WAN[3] as hwname= ifname=
SysInit: Initialize System Misc Modules
LANInit: Initialize LAN with LANCount=1
Cellular: Start Mobile Broadband Cellular Manager as pid 351
main: Reading saved status
main: Received UEvent saved message as devstatus=0x00000000, device=/dev/ttyUSB2
Cellular: Cellular was NOT ready right now
Cellular: Start cellular device process as devstate=0x00000000
LAN: Refresh LAN[0] as ifname=br0 ipaddr=192.168.1.1 netmask=255.255.255.0 proto=static
WANInit: Initialize WAN with WANCount=4
WanConn[3]: Refresh WAN  proto=CELLNCM as CellProf=12d1:1506:3_Italia
WLANInit: Initialize WLAN with APCount=1, WDSCount=0, STACount=0
WLAN: Refresh WLAN Settings as Enable=1, Standard=N, Channel=0, RegulatoryDomain=IT
WlanAP[0]: Refresh AP with Enable=1 SSID=XLIGHT-9177 Security=WPAand11i_PSK_TKIPAES WMMEnable=1
HTTPDInit: Initialize HTTPD with Primary/Guest WebUI support and Guest LANID is 1
HTTPD: Refresh HTTPD as PrimaryIP=192.168.1.1 GuestIP=0.0.0.0 RemoteIP=0.0.0.0
DNSMasqInit: Initialize DNSMASQ with DHCPD support
DNSMasq: Refresh DNSMASQ as opmode=3, gendns1=168.126.63.1, gendns2=156.154.70.1
DNSMasq: Refresh DHCPD for LAN[0] as ip_start=192.168.1.100 ip_end=192.168.1.200 dns1=4.2.2.4 dns2=156.154.70.1
upnp: Refresh UPNP ModuleData.
upnp: Initialize UPNP as Disable
FIRMUPGRADE: Refresh UPGRADE Module data
FIRMUPGRADE: Initialize UPGRADE Module
Firewall: Register Firewall...
Firewall: Clearup firewall
UEvent: USBDevice Process for 12d1:1506, recognized as E8238 Cellular Standard Mode with 5 ttys, 1 sddisk
UEvent: USBDev TTY add for 12d1:1506:0102 TYPE=00:00:00 INTERFACE=ff:02:01 DEVTYPE=usb_interface SUBSYSTEM=tty devname=[ttyUSB0]
UEvent: USBDev TTY add for 12d1:1506:0102 TYPE=00:00:00 INTERFACE=ff:02:03 DEVTYPE=usb_interface SUBSYSTEM=tty devname=[ttyUSB1]
UEvent: USBDev TTY add for 12d1:1506:0102 TYPE=00:00:00 INTERFACE=ff:02:02 DEVTYPE=usb_interface SUBSYSTEM=tty devname=[ttyUSB2]
UEvent: Cellular 12d1:1506 TTY devices is now RECOGNIZED and READY as Data=/dev/ttyUSB0 ATCmd=/dev/ttyUSB2 Diag=/dev/ttyUSB1
UEvent: Inform cellular daemon pid=351 as updated devstatus 0x00000006 ATCmd=/dev/ttyUSB2 Data=/dev/ttyUSB0 Diag=/dev/ttyUSB1
UEvent: USBDev TTY add for 12d1:1506:0102 TYPE=00:00:00 INTERFACE=ff:02:05 DEVTYPE=usb_interface SUBSYSTEM=tty devname=[ttyUSB3]
UEvent: USBDev TTY add for 12d1:1506:0102 TYPE=00:00:00 INTERFACE=ff:02:0a DEVTYPE=usb_interface SUBSYSTEM=tty devname=[ttyUSB4]
ctflush: flush conntrack (OK)
Firewall: Done.
InitProc: Switch to START state in mainloop
LAN: Set LAN[0] as ifname=br0 ipaddr=192.168.1.1 netmask=255.255.255.0 hwaddr=00:00:00:00:00:00
LAN: Set LAN[0] ifnames=[ath0] ifnames_post=[ath0]
LAN: Current LAN[0] br0 hwaddr=00:00:00:00:00:00 ipaddr=192.168.1.1 netmask=255.255.255.0, Bridged []
WanAPI[3]: StartWAN API AutoStart as Prof=12d1:1506:3_Italia status=STOP APNIdTry=0 demand=1 manual_forced=0
WanAPI[3]: StartWAN API Proceed to WAN SETUP process
WanConn[3]: Start WAN SETUP as PROTO=CELLNCM CellProf=12d1:1506:3_Italia APNIdTry=0 hwname=wwan0 retry_times=0 redial_times=0
WanConn[3]: Start WAN PREPARE as PROTO=CELLNCM CellProf=12d1:1506:3_Italia APNIdTry=0 hwname=wwan0 retry_times=0 redial_times=0
WanCellNCM[3]: Cellular NCM PREPARE failure as interface wwan0 not exist
WLAN: Start WLAN with APCount=1, WDSCount=0, STACount=0, Standard=N, Channel=0
WlanAP[0]: Start AP with SSID=XLIGHT-9177 Standard=N Channel=0 Security=WPAand11i_PSK_TKIPAES
DNSMasq: DNSMASQ was launched as pid=422 opmode=3
InitProc: Launch user console
TimerProc: Stop timerproc [CellReset]
SDT: Start Huawei SDT
TimerProc: Stop timerproc [CellReset]
# LAN: Add WLAN AP[0] post interface ath0 to LAN[0] br0
LAN: LAN[0] br0 hwaddr was updated to 78:F5:FD:1E:91:77
Hostapd[0]: Create hostapd conf at /tmp/hostapd/hostapd0.conf for interface=ath0 bridge=br0
Hostapd[0]: Set WLAN ath0 SSID=XLIGHT-9177 Standard=N Channel=0
Hostapd[0]: Set WLAN ACL GenericPolicy=Deny RulesCount=0
Hostapd[0]: Set WLAN WMM to default WMM parameters from IEEE 802.11 draft; 11-03-0504-03-000e
Hostapd[0]: Set security as WPAand11i_PSK_TKIPAES, group_rekey=600 strict_rekey=1 gmk_rekey=86400 ptk_rekey=600
Hostapd[0]: Launch hostapd base on /tmp/hostapd/hostapd0.conf at pid=442
Configuration file: /tmp/hostapd/hostapd0.conf
ath0: Could not connect to kernel driver
Using interface ath0 with hwaddr 78:f5:fd:1e:91:77 and ssid "XLIGHT-9177"
random: Only 16/20 bytes of strong random data available from /dev/random
random: Not enough entropy pool available for secure operations
WPA: Not enough entropy in random pool for secure operations - update keys later when the first station connects
UEvent: USBDev DISK add for 12d1:1506:0102 TYPE=00:00:00 INTERFACE=08:06:50 DEVTYPE=usb_interface SUBSYSTEM=block devname=[sda]
UEvent: Cellular SD DISK device is now RECOGNIZED as devfullpath=/dev/sda
UEvent: VFAT file system check as devfullpath=/dev/sda
dosfsck 2.11, 12 Mar 2005, FAT32, LFN
/dev/sda: 12 files, 12/29064 clusters
WanCellNCM[3]: Cellular NCM PREPARE failure as interface wwan0 not exist
UEvent: Preparing for SD DISK /dev/sda SUCCESS and inform init
UEvent: Inform cellular daemon pid=351 as updated devstatus 0x0000003e ATCmd=/dev/ttyUSB2 Data=/dev/ttyUSB0 Diag=/dev/ttyUSB1
Cellular: Modem device up.
cellproc_setup_cellprof: Opening device: /dev/ttyUSB2
Cellular: SD storage device up and ready.
[shortmessage.c,XMLDOC_SMSLoad,283]: Loading compressed XML from /cellsd/sms/inbox/sms.xml
[shortmessage.c,XMLDOC_SMSLoad,316]: Decompress configuration, size: 12618
[shortmessage.c,XMLDOC_UpdateQuotaSummary,193]: SMS internal memory usage: 21 of 500
[shortmessage.c,XMLDOC_UpdateQuotaSummary,195]: SMS USIM memory usage: 0 of 500
[shortmessage.c,XMLDOC_SMSLoad,283]: Loading compressed XML from /cellsd/sms/sent/sms.xml
[shortmessage.c,XMLDOC_SMSLoad,316]: Decompress configuration, size: 45
[shortmessage.c,XMLDOC_UpdateQuotaSummary,193]: SMS internal memory usage: 21 of 500
[shortmessage.c,XMLDOC_UpdateQuotaSummary,195]: SMS USIM memory usage: 0 of 500
[shortmessage.c,XMLDOC_SMSLoad,283]: Loading compressed XML from /cellsd/sms/drafts/sms.xml
[shortmessage.c,XMLDOC_SMSLoad,316]: Decompress configuration, size: 45
[shortmessage.c,XMLDOC_UpdateQuotaSummary,193]: SMS internal memory usage: 21 of 500
[shortmessage.c,XMLDOC_UpdateQuotaSummary,195]: SMS USIM memory usage: 0 of 500
[shortmessage.c,XMLDOC_SMSLoad,283]: Loading compressed XML from /tmp/inbox_usim.xml
[shortmessage.c,XMLDOC_SMSLoad,328]: Create empty SMS record file: /tmp/inbox_usim.xml
[shortmessage.c,XMLDOC_UpdateQuotaSummary,193]: SMS internal memory usage: 21 of 500
[shortmessage.c,XMLDOC_UpdateQuotaSummary,195]: SMS USIM memory usage: 0 of 500
[shortmessage.c,XMLDOC_SMSLoad,283]: Loading compressed XML from /tmp/sent_usim.xml
[shortmessage.c,XMLDOC_SMSLoad,328]: Create empty SMS record file: /tmp/sent_usim.xml
[shortmessage.c,XMLDOC_UpdateQuotaSummary,193]: SMS internal memory usage: 21 of 500
[shortmessage.c,XMLDOC_UpdateQuotaSummary,195]: SMS USIM memory usage: 0 of 500
[shortmessage.c,XMLDOC_SMSLoad,283]: Loading compressed XML from /tmp/drafts_usim.xml
[shortmessage.c,XMLDOC_SMSLoad,328]: Create empty SMS record file: /tmp/drafts_usim.xml
[shortmessage.c,XMLDOC_UpdateQuotaSummary,193]: SMS internal memory usage: 21 of 500
[shortmessage.c,XMLDOC_UpdateQuotaSummary,195]: SMS USIM memory usage: 0 of 500
device_input_process: Fail to turn off modem echo, try again...
WanCellNCM[3]: Cellular NCM PREPARE failure as interface wwan0 not exist
SDT: Found USB device : /dev/ttyUSB0
SDT: Found USB device : /dev/ttyUSB1
SDT: Found USB device : /dev/ttyUSB2
SDT: Found USB device : /dev/ttyUSB3
SDT: Found USB device : /dev/ttyUSB4
SDT: bind port : 4000, device : /dev/ttyUSB0
SDT: bind port : 3000, device : /dev/ttyUSB1
SDT: bind port : 3001, device : /dev/ttyUSB2
WanCellNCM[3]: Cellular NCM PREPARE failure as interface wwan0 not exist
WanCellNCM[3]: Cellular NCM PREPARE failure as interface wwan0 not exist
WanCellNCM[3]: Cellular NCM PREPARE failure as interface wwan0 not exist
WanCellNCM[3]: Cellular NCM PREPARE failure as interface wwan0 not exist
WanCellNCM[3]: Cellular NCM PREPARE failure as interface wwan0 not exist
WanCellNCM[3]: Cellular NCM PREPARE failure as interface wwan0 not exist
WanCellNCM[3]: Cellular NCM PREPARE failure as interface wwan0 not exist
WanCellNCM[3]: Cellular NCM PREPARE failure as interface wwan0 not exist
WanCellNCM[3]: Cellular NCM PREPARE failure as interface wwan0 not exist
WanCellNCM[3]: Cellular NCM PREPARE failure as interface wwan0 not exist
WanCellNCM[3]: Cellular NCM PREPARE failure as interface wwan0 not exist
WanCellNCM[3]: Cellular NCM PREPARE failure as interface wwan0 not exist
WanCellNCM[3]: Cellular NCM PREPARE failure as interface wwan0 not exist
WanCellNCM[3]: Cellular NCM PREPARE failure as interface wwan0 not exist