移远通讯BC260Y CN STM32G0串口下载教程

下载前，需要先断电并将BOOT0处红⾊开关拨 ⾄“NO”，并再次接上数据线，打开STM32CubeProgrammer，选择UART模式，点击右上⻆的“Connect”按钮，显示绿⾊“Connected”图标时即为连接成功

点击左侧的下载图标，进⼊Erasing & Programming界⾯，并点击“Browse”选择需要的烧录的 程序

点击右上⻆的“Disconnect”按钮断开连接，并断电，将底板上的红⾊开关码拨到“1”，拔掉数据线重启后再连接。

 下载好后显示的灯 

一个红色1个蓝色常量 

注意下载的时候波特率是115200，使用串口软件是9600 ，程序路径不要有中文

AT

OK
AT

OK
AT

OK
AT

OK
AT+CFUN=1

OK
AT+QMTDISC=0

OK

+QMTDISC: 0,0
AT+CIMI

460083501703547

OK
AT+CGATT=1

OK
AT+CGATT?

+CGATT: 1

OK
AT+CESQ

+CESQ: 99,99,255,255,34,70

OK
AT+QMTCFG="aliauth",0,"a1ZMkwhevG9","mzh001","cc96840980ac49570acc47e2c0195b5c"

OK
AT+QMTOPEN=0,"139.196.135.135",1883

OK

+QMTOPEN: 0,0
AT+QMTCONN=0,"clientExample_1987"

OK

+QMTCONN: 0,0,0
AT+QMTPUB=0,0,0,0,/sys/a1ZMkwhevG9/mzh001/thing/event/property/post

>
{"id":"26","version":"1.0","sys":{"ack":0},"params":{"CurrentTemperature":{"value":22},"CurrentHumidity":{"value":30}},"method":"thing.event.property.post"}
OK

+QMTPUB: 0,0,0
AT+QMTPUB=0,0,0,0,/sys/a1ZMkwhevG9/mzh001/thing/event/property/post

>
{"id":"26","version":"1.0","sys":{"ack":0},"params":{"CurrentTemperature":{"value":22},"CurrentHumidity":{"value":30}},"method":"thing.event.property.post"}
OK

+QMTPUB: 0,0,0

+AT+QMTPUB=0,0,0,0,/sys/a1ZMkwhevG9/mzh001/thing/event/property/post

>
{"id":"26","version":"1.0","sys":{"ack":0},"params":{"CurrentTemperature":{"value":22},"CurrentHumidity":{"value":30}},"method":"thing.event.property.post"}
OK

+QMTPUB: 0,0,0

+
AT+QMTPUB=0,0,0,0,/sys/a1ZMkwhevG9/mzh001/thing/event/property/post

>
{"id":"26","version":"1.0","sys":{"ack":0},"params":{"CurrentTemperature":{"value":22},"CurrentHumidity":{"value":30}},"method":"thing.event.property.post"}
OK

+QMTPUB: 0,0,0

+}"
AT+QMTPUB=0,0,0,0,/sys/a1ZMkwhevG9/mzh001/thing/event/property/post

>
{"id":"26","version":"1.0","sys":{"ack":0},"params":{"CurrentTemperature":{"value":22},"CurrentHumidity":{"value":30}},"method":"thing.event.property.post"}
OK

+QMTPUB: 0,0,0

+t"}"
AT+QMTPUB=0,0,0,0,/sys/a1ZMkwhevG9/mzh001/thing/event/property/post

>
{"id":"26","version":"1.0","sys":{"ack":0},"params":{"CurrentTemperature":{"value":22},"CurrentHumidity":{"value":30}},"method":"thing.event.property.post"}
OK

+QMTPUB: 0,0,0

+y.post"}"
AT

OK
AT

OK
AT

OC程序源码，采集温湿度

/* USER CODE BEGIN Header */
/**
  ******************************************************************************
  * @file           : main.c
  * @brief          : Main program body
  ******************************************************************************
  * @attention
  *
  * <h2><center>&copy; Copyright (c) 2021 STMicroelectronics.
  * All rights reserved.</center></h2>
  *
  * This software component is licensed by ST under BSD 3-Clause license,
  * the "License"; You may not use this file except in compliance with the
  * License. You may obtain a copy of the License at:
  *                        opensource.org/licenses/BSD-3-Clause
  *
  ******************************************************************************
  */
/* USER CODE END Header */

/* Includes ------------------------------------------------------------------*/
#include "main.h"
#include "usart.h"
#include "stdlib.h"
#include "string.h"
#include "stdlib.h"
#include "BC260Y.h"
#include "AHT20.h"
IWDG_HandleTypeDef hiwdg;
/* Private includes ----------------------------------------------------------*/
/* USER CODE BEGIN Includes */

/* USER CODE END Includes */

/* Private typedef -----------------------------------------------------------*/
/* USER CODE BEGIN PTD */

/* USER CODE END PTD */

/* Private define ------------------------------------------------------------*/
/* USER CODE BEGIN PD */

/* USER CODE END PD */

/* Private macro -------------------------------------------------------------*/
/* USER CODE BEGIN PM */

/* USER CODE END PM */

/* Private variables ---------------------------------------------------------*/

/* USER CODE BEGIN PV */

/* USER CODE END PV */

/* Private function prototypes -----------------------------------------------*/
void SystemClock_Config(void);
static void MX_GPIO_Init(void);
static void MX_IWDG_Init(void);
void IWDG_Feed(void);
/* USER CODE BEGIN PFP */

/* USER CODE END PFP */

/* Private user code ---------------------------------------------------------*/
/* USER CODE BEGIN 0 */

/* USER CODE END 0 */
void OPEN_BC260Y(void)
{
	char *strx;
		printf("AT\r\n"); 
		HAL_Delay(300);
		strx=strstr((const char*)RxBuffer,(const char*)"OK");//返回OK
		printf("AT\r\n"); 
		HAL_Delay(300);
		strx=strstr((const char*)RxBuffer,(const char*)"OK");//返回OK
	if(strx==NULL)
	{
  HAL_GPIO_WritePin(GPIOA, GPIO_PIN_0,GPIO_PIN_SET);//拉低PWRKEY
	HAL_Delay(600);
	HAL_Delay(600);
  HAL_GPIO_WritePin(GPIOA, GPIO_PIN_0,GPIO_PIN_RESET);//拉高正常开机
   IWDG_Feed();//喂狗
	}
	printf("AT\r\n"); 
		HAL_Delay(300);
	 IWDG_Feed();//喂狗
		strx=strstr((const char*)RxBuffer,(const char*)"OK");//返回OK
		while(strx==NULL)
		{
				Clear_Buffer();	
				printf("AT\r\n"); 
				HAL_Delay(300);
			  HAL_GPIO_TogglePin(GPIOB, GPIO_PIN_0);
				strx=strstr((const char*)RxBuffer,(const char*)"OK");//返回OK
		}
    HAL_GPIO_WritePin(GPIOB, GPIO_PIN_0,0);
		 IWDG_Feed();//喂狗
}
void Send_ATcmd(void)//发送AT指令给到模块，从串口1接收指令，串口2控制
{
	char i;
	for(i=0;i<Uart1_Rx_Cnt;i++)
	{
	 while((USART2->ISR&0X40)==0){}//等待发送完成 
	  USART2->TDR = Uart1_RxBuff[i]; 
	}
}

/**
  * @brief  The application entry point.
  * @retval int
  */
int main(void)
{
	unsigned char i;
	uint8_t ret = 0;
	uint32_t CT_data[2];
	uint8_t send_jason[200];
	int  c1,t1;
  /* Reset of all peripherals, Initializes the Flash interface and the Systick. */
  HAL_Init();
  SystemClock_Config();
  /* Initialize all configured peripherals */
  MX_GPIO_Init();
	MX_IWDG_Init();
  MX_USART1_UART_Init();
	MX_USART2_UART_Init();
	HAL_Delay(500);
	I2C_Bus_Init();
	ret = AHT20_Init();
	if(ret == 0)
	{
				while(1)
				{     
					Uart1_SendStr("AHT20传感器初始化错误\n");
					HAL_Delay(300);
				}

	}
  /* USER CODE BEGIN 2 */
	// OPEN_BC260Y();
  /* USER CODE END 2 */
	BC260Y_Init();
  MQTT_Init();//初始化MQTT
  while (1)
  {
	 /* 读取 AHT20 传感器数据*/
        while(AHT20_Read_Cal_Enable() == 0)
        {
            AHT20_Init();//如果为0再使能一次
            HAL_Delay(30);
        }
			AHT20_Read_CTdata(CT_data);  //读取温度和湿度
			c1 = CT_data[0] * 1000 / 1024 / 1024;  //计算得到湿度值（放大了10倍,如果c1=523，表示现在湿度为52.3%）
			t1 = CT_data[1] * 200 *10 / 1024 / 1024 - 500;//计算得到温度值（放大了10倍，如果t1=245，表示现在温度为24.5℃）
		  ONENET_SendJsondata(send_jason,t1/10,c1/10);//发布数据
			HAL_GPIO_TogglePin(GPIOB, GPIO_PIN_0);
		  HAL_Delay(300);
		//	HAL_GPIO_TogglePin(GPIOB, GPIO_PIN_0);
     IWDG_Feed();//喂狗
  }
  /* USER CODE END 3 */
}

/**
  * @brief System Clock Configuration
  * @retval None
  */
void SystemClock_Config(void)
{
  RCC_OscInitTypeDef RCC_OscInitStruct = {0};
  RCC_ClkInitTypeDef RCC_ClkInitStruct = {0};
  RCC_PeriphCLKInitTypeDef PeriphClkInit = {0};

  /** Configure the main internal regulator output voltage 
  */
  HAL_PWREx_ControlVoltageScaling(PWR_REGULATOR_VOLTAGE_SCALE1);
  /** Initializes the CPU, AHB and APB busses clocks 
  */
  RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_LSI|RCC_OSCILLATORTYPE_HSE;
  RCC_OscInitStruct.HSEState = RCC_HSE_ON;
  RCC_OscInitStruct.LSIState = RCC_LSI_ON;
  RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
  RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE;
  RCC_OscInitStruct.PLL.PLLM = RCC_PLLM_DIV1;
  RCC_OscInitStruct.PLL.PLLN = 16;
  RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV2;
  RCC_OscInitStruct.PLL.PLLR = RCC_PLLR_DIV2;
  if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK)
  {
    Error_Handler();
  }
  /** Initializes the CPU, AHB and APB busses clocks 
  */
  RCC_ClkInitStruct.ClockType = RCC_CLOCKTYPE_HCLK|RCC_CLOCKTYPE_SYSCLK
                              |RCC_CLOCKTYPE_PCLK1;
  RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK;
  RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1;
  RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV1;

  if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_2) != HAL_OK)
  {
    Error_Handler();
  }
  /** Initializes the peripherals clocks 
  */
  PeriphClkInit.PeriphClockSelection = RCC_PERIPHCLK_USART1|RCC_PERIPHCLK_USART2;
  PeriphClkInit.Usart1ClockSelection = RCC_USART1CLKSOURCE_PCLK1;
  if (HAL_RCCEx_PeriphCLKConfig(&PeriphClkInit) != HAL_OK)
  {
    Error_Handler();
  }
}


/**
  * @brief GPIO Initialization Function
  * @param None
  * @retval None
  */
static void MX_GPIO_Init(void)
{
  GPIO_InitTypeDef GPIO_InitStruct = {0};

  /* GPIO Ports Clock Enable */
  __HAL_RCC_GPIOF_CLK_ENABLE();
  __HAL_RCC_GPIOB_CLK_ENABLE();
  __HAL_RCC_GPIOA_CLK_ENABLE();

  /*Configure GPIO pin Output Level */
  HAL_GPIO_WritePin(GPIOB, GPIO_PIN_0, GPIO_PIN_RESET);
  /*Configure GPIO pin : PB0 */
  GPIO_InitStruct.Pin = GPIO_PIN_0;
  GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP;
  GPIO_InitStruct.Pull = GPIO_NOPULL;
  GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_LOW;
  HAL_GPIO_Init(GPIOB, &GPIO_InitStruct);
	  /*Configure GPIO pin Output Level */

	  /*Configure GPIO pin : PA0 */
  GPIO_InitStruct.Pin = GPIO_PIN_0;
  GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP;
  GPIO_InitStruct.Pull = GPIO_NOPULL;
  GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_LOW;
  HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
  HAL_GPIO_WritePin(GPIOA, GPIO_PIN_0, GPIO_PIN_SET);
}

/* USER CODE BEGIN 4 */
/**
  * @brief IWDG Initialization Function
  * @param None
  * @retval None
  */
static void MX_IWDG_Init(void)
{

  /* USER CODE BEGIN IWDG_Init 0 */

  /* USER CODE END IWDG_Init 0 */

  /* USER CODE BEGIN IWDG_Init 1 */

  /* USER CODE END IWDG_Init 1 */
  hiwdg.Instance = IWDG;
  hiwdg.Init.Prescaler = IWDG_PRESCALER_64;
  hiwdg.Init.Window = 4000;
  hiwdg.Init.Reload = 4000;
  if (HAL_IWDG_Init(&hiwdg) != HAL_OK)
  {
    Error_Handler();
  }
  /* USER CODE BEGIN IWDG_Init 2 */

  /* USER CODE END IWDG_Init 2 */

}

/* USER CODE END 4 */

/**
  * @brief  This function is executed in case of error occurrence.
  * @retval None
  */


#ifdef  USE_FULL_ASSERT
/**
  * @brief  Reports the name of the source file and the source line number
  *         where the assert_param error has occurred.
  * @param  file: pointer to the source file name
  * @param  line: assert_param error line source number
  * @retval None
  */
void assert_failed(uint8_t *file, uint32_t line)
{ 
  /* USER CODE BEGIN 6 */
  /* User can add his own implementation to report the file name and line number,
     tex: printf("Wrong parameters value: file %s on line %d\r\n", file, line) */
  /* USER CODE END 6 */
}
#endif /* USE_FULL_ASSERT */

/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/