实验 10 点到点链路 OSPF 配置

一．实验目的：
掌握点到点链路 OSPF 的配置方法。
二．实验要点：
配置点到点链路上的 OSPF，对运行中的 OSPF 进行诊断。
三．实验设备：
路由器 Cisco 2621 三台，带有网卡的工作站 PC 六台，控制台电缆一条，交叉双绞线若干。
四、实验环境
步骤中的实验情况

纠正一下，Router1的f0/0端口的地址为：20.0.0.1/24

将所有的主机配置好之后出现的情况

五. 实验步骤

Router1的配置
Router>enable
Router#configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#interface Serial0/0
Router(config-if)#ip address 192.168.1.2 255.255.255.0
Router(config-if)#clock rate 64000
Router(config-if)#no shutdown
Router(config-if)#
%LINK-5-CHANGED: Interface Serial0/0, changed state to up

Router(config-if)#exit
Router(config)#interface Serial0/1
Router(config-if)#ip address 192.168.3.1 255.255.255.0
Router(config-if)#clock rate 64000
Router(config-if)#no shutdown
Router(config-if)#
%LINK-5-CHANGED: Interface Serial0/1, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/1, changed state to up

Router2的配置
Router>enable
Router#configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#interface Serial0/0
Router(config-if)#ip address 192.168.2.2 255.255.255.0
Router(config-if)#clock rate 64000
This command applies only to DCE interfaces
Router(config-if)#no shutdown
Router(config-if)#
%LINK-5-CHANGED: Interface Serial0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0, changed state to up

Router(config-if)#exit
Router(config)#interface Serial0/1
Router(config-if)#ip address 192.168.3.2 255.255.255.0
Router(config-if)#clock rate 64000
This command applies only to DCE interfaces
Router(config-if)#no shutdown
Router(config-if)#
%LINK-5-CHANGED: Interface Serial0/1, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/1, changed state to up

Router0的配置
Router>enable
Router#configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#interface Serial0/0
Router(config-if)#ip address 192.168.1.1 255.255.255.0
Router(config-if)#clock rate 64000
This command applies only to DCE interfaces
Router(config-if)#no shutdown
Router(config-if)#
Router(config-if)#exit
Router(config)#interface Serial0/1
Router(config-if)#ip address 192.168.2.1 255.255.255.0
Router(config-if)#clock rate 64000
Router(config-if)#no shutdown
Router(config-if)#
%LINK-5-CHANGED: Interface Serial0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0, changed state to up

%LINK-5-CHANGED: Interface Serial0/1, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/1, changed state to up

Router(config-if)#exit
Router(config)#router ospf 1
Router(config-router)#network 192.168.1.0 0.0.0.255 area 0
Router(config-router)#network 192.168.2.0 0.0.0.255 area 0
Router(config-router)#exit
Router(config)#exit
Router#
%SYS-5-CONFIG_I: Configured from console by console

Router#ping 192.168.1.2

Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.1.2, timeout is 2 seconds:
!!!!!
Success rate is