RIP认证实验案例

实验工具：ensp
一、实验拓扑

二、实验需求
1、SW2和SW3为二层交换机，SW1为三层交换机。
2、R1与SW2之间做单臂路由；SW1和SW3之间做VLAN间路由。
3、全网IP网段和VLAN规划如上图所示，要求所有互联网段从192.168.0.0/24网段规划所得，子网掩码均为30位。全网路由使用RIPv2。
4、要求R1学习到192.168.3.0/24、192.168.4.0/24网段从R3学习到；
5、要求SW1学习到192.168.1.0/24、192.168.2.0/24网段从R2学习到。
6、R1、R2、R3之间的端口上开启认证，认证的方式采用MD5认证，密码为666.
7、将R1与PC机相连的端口设置为抑制接口。

三、实验步骤
R1:
sysname r1
undo info-center enable
interface Ethernet0/0/0
 ip address 10.1.1.1 255.255.255.252 
 rip authentication-mode md5 usual cw7w53+h=YajUn1vMEIBFGw#
interface Ethernet0/0/1
 ip address 10.1.2.1 255.255.255.252 
 rip authentication-mode md5 usual @\|mJ._fR8ECB7Ie7'/)2GB#
GigabitEthernet0/0/0.10
 dot1q termination vid 10
 ip address 192.10.1.1 255.255.255.0 
 arp broadcast enable
interface GigabitEthernet0/0/0.20
 dot1q termination vid 20
 arp broadcast enable
rip 1
 undo summary
 version 2
 network 10.0.0.0
 network 192.10.1.0
 network 192.10.2.0
R2:
sysname r2
undo info-center enable
interface Ethernet0/0/0
 ip address 10.1.1.2 255.255.255.252 
 rip authentication-mode md5 usual @$CxEuV+P:bL^B&WSBiQ\H[#
interface Ethernet0/0/1
 ip address 10.1.1.5 255.255.255.252 
 rip metricin 2 
rip 1
 undo summary
 version 2
 network 10.0.0.0
S1:
sysname s1
undo info-center enable
vlan batch 30 40 100 200
interface Vlanif30
 ip address 192.10.3.1 255.255.255.0 
interface Vlanif40
 ip address 192.10.4.1 255.255.255.0 
interface Vlanif100
 ip address 10.1.1.6 255.255.255.252 
interface Vlanif200
 ip address 10.1.2.6 255.255.255.252 
interface GigabitEthernet0/0/1
 port link-type access
 port default vlan 200
interface GigabitEthernet0/0/2
 port link-type access
 port default vlan 100
interface GigabitEthernet0/0/3
 port link-type trunk
 port trunk allow-pass vlan 30 40
rip 1
 version 2
 network 10.0.0.0
 network 192.10.3.0
 network 192.10.4.0
R3:
sysname r3
undo info-center enable
interface Ethernet0/0/0
 ip address 10.1.2.2 255.255.255.252 
 rip authentication-mode md5 usual fR"9GqC;M3jKUGU-KkpBXI/#
 rip metricin 2 
interface Ethernet0/0/1
 ip address 10.1.2.5 255.255.255.252 
rip 1
 undo summary
 version 2
 network 10.0.0.0
S2:
sysname s2
undo info-center enable
vlan batch 10 20
interface Ethernet0/0/1
 port link-type trunk
 port trunk allow-pass vlan 10 20
interface Ethernet0/0/2
 port link-type access
 port default vlan 10
interface Ethernet0/0/3
 port link-type access
 port default vlan 20
S3:
sysname s3
undo info-center enable
vlan batch 30 40
interface Ethernet0/0/1
 port link-type trunk
 port trunk allow-pass vlan 30 40
interface Ethernet0/0/2
 port link-type access
 port default vlan 30
interface Ethernet0/0/3
 port link-type access
 port default vlan 40

四、实验截图